near future (Rpi3)

classic Classic list List threaded Threaded
5 messages Options
Reply | Threaded
Open this post in threaded view
|

near future (Rpi3)

Tuyosi Takesima
hi all .

i try again to install arm to raspberry pi 3 .
i use miniroot61.fs of 6th april version .

insert micro sd card(S1) with usb card reader(which has micro sd card(S2)).


at the end of installing
------------------------>
Set name(s)? (or 'abort' or 'done') [done]

Get/Verify SHA256.sig   100% |**************************|  1381       00:00

Signature Verified

Get/Verify bsd          100% |**************************|  5433 KB    00:36

Get/Verify bsd.rd       100% |**************************| 11059 KB    01:15

Get/Verify base61.tgz   100% |**************************| 75067 KB    08:03

Installing bsd          100% |**************************|  5433 KB    00:00

Installing bsd.rd       100% |**************************| 11059 KB    00:01

Installing base61.tgz   100% |**************************| 75067 KB    02:10

Extracting etc.tgz      100% |**************************|   189 KB    00:01

Location of sets? (disk http nfs or 'done') [done]
      Time appears wrong.  Set to 'Sat Apr  8 09:43:37 JST 2017'? [yes]
Saving configuration files...done.

Making all device nodes...done.


# df

Filesystem  512-blocks      Used     Avail Capacity  Mounted on
/dev/rd0a        14823     13150      1673    89%    /

/dev/sd0a     15446556    573924  14100308     4%    /mnt
/dev/sd0i        32668      6636     26032    20%    /mnt/mnt

halt -p
---------------------<



then i insert micro sd card(S2) and power on
--------------------->>
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC953
smsc0: address b8:27:eb:c3:cc:1a

ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001fc
umass0 at uhub1 port 2 configuration 1 interface 0 "Generic Mass Storage
Device4
umass0: using SCSI over Bulk-Only

scsibus0 at umass0: 2 targets, initiator 0

sd0 at scsibus0 targ 1 lun 0: <Multi, Flash Reader, 1.00> SCSI0 0/direct
remova1
vscsi0 at root

scsibus1 at vscsi0: 256 targets

softraid0 at root

scsibus2 at softraid0: 256 targets

bootfile: sd0a:/bsd

boot device: sd0

panic: root device (22692e8a0bb8a762) not found

Stopped at      panic+0x158:        TID    PID    UID     PRFLAGS
PFLAGS  C
PU  COMMAND

*     0      0      0     0x10000      0x200    0  swapper

Debugger() at panic+0x154

panic() at diskconf+0xac

diskconf() at main+0x46c

main() at $x.2+0x70

https://www.openbsd.org/ddb.html describes the minimum info required in bug

reports.  Insufficient info makes it difficult to find and fix bugs.

ddb>
-------------------<<

i think the day which raspberry pi 3 runs openbsd will be near future .

-
regards
Reply | Threaded
Open this post in threaded view
|

Re: near future (Rpi3)

Jonathan Gray-11
On Sat, Apr 08, 2017 at 10:11:53AM +0900, Tuyosi T wrote:

> hi all .
>
> i try again to install arm to raspberry pi 3 .
> i use miniroot61.fs of 6th april version .
>
> insert micro sd card(S1) with usb card reader(which has micro sd card(S2)).
>
>
> at the end of installing
> ------------------------>
> Set name(s)? (or 'abort' or 'done') [done]
>
> Get/Verify SHA256.sig   100% |**************************|  1381       00:00
>
> Signature Verified
>
> Get/Verify bsd          100% |**************************|  5433 KB    00:36
>
> Get/Verify bsd.rd       100% |**************************| 11059 KB    01:15
>
> Get/Verify base61.tgz   100% |**************************| 75067 KB    08:03
>
> Installing bsd          100% |**************************|  5433 KB    00:00
>
> Installing bsd.rd       100% |**************************| 11059 KB    00:01
>
> Installing base61.tgz   100% |**************************| 75067 KB    02:10
>
> Extracting etc.tgz      100% |**************************|   189 KB    00:01
>
> Location of sets? (disk http nfs or 'done') [done]
>       Time appears wrong.  Set to 'Sat Apr  8 09:43:37 JST 2017'? [yes]
> Saving configuration files...done.
>
> Making all device nodes...done.
>
>
> # df
>
> Filesystem  512-blocks      Used     Avail Capacity  Mounted on
> /dev/rd0a        14823     13150      1673    89%    /
>
> /dev/sd0a     15446556    573924  14100308     4%    /mnt
> /dev/sd0i        32668      6636     26032    20%    /mnt/mnt
>
> halt -p
> ---------------------<
>
>
>
> then i insert micro sd card(S2) and power on

At this point you need to type commands into U-Boot so it will use the
USB disk.

Hit any key to stop autoboot:  0
U-Boot> setenv boot_targets usb0 mmc0 pxe dhcp
U-Boot> saveenv
U-Boot> boot


> --------------------->>
> smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
> SMSC953
> smsc0: address b8:27:eb:c3:cc:1a
>
> ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x0001fc
> umass0 at uhub1 port 2 configuration 1 interface 0 "Generic Mass Storage
> Device4
> umass0: using SCSI over Bulk-Only
>
> scsibus0 at umass0: 2 targets, initiator 0
>
> sd0 at scsibus0 targ 1 lun 0: <Multi, Flash Reader, 1.00> SCSI0 0/direct
> remova1
> vscsi0 at root
>
> scsibus1 at vscsi0: 256 targets
>
> softraid0 at root
>
> scsibus2 at softraid0: 256 targets
>
> bootfile: sd0a:/bsd
>
> boot device: sd0
>
> panic: root device (22692e8a0bb8a762) not found

Reply | Threaded
Open this post in threaded view
|

Re: near future (Rpi3)

Tuyosi Takesima
In reply to this post by Tuyosi Takesima
i failed
details is next

---------------------------------
Err:   lcd

Net:   Net Initialization Skipped

No ethernet found.

starting USB...

USB0:   Core Release: 2.80a

scanning bus 0 for devices...

      USB device not accepting new address (error=0)

3 USB Device(s) found

       scanning usb for storage devices... 0 Storage Device(s) found

       scanning usb for ethernet devices... 1 Ethernet Device(s) found

Hit any key to stop autoboot:  0

U-Boot> setenv boot_targets us0 m0 x dc

U-Boot> saveenv

Saving Environment to FAT...

writing uboot.env

FAT: Misaligned buffer address (000000003ab2ab50)

sdhci_send_command: MMC: 0 busy timeout increasing to: 200 ms.

done

U-Boot> boot

## Error: "bootcmd_us0" not defined

## Error: "bootcmd_m0" not defined

## Error: "bootcmd_x" not defined

## Error: "bootcmd_dc" not defined

U-Boot>


-
regards
Reply | Threaded
Open this post in threaded view
|

Re: near future (Rpi3)

Jonathan Gray-11
On Sat, Apr 08, 2017 at 11:10:09AM +0900, Tuyosi T wrote:

> i failed
> details is next
>
> ---------------------------------
> Err:   lcd
>
> Net:   Net Initialization Skipped
>
> No ethernet found.
>
> starting USB...
>
> USB0:   Core Release: 2.80a
>
> scanning bus 0 for devices...
>
>       USB device not accepting new address (error=0)
>
> 3 USB Device(s) found
>
>        scanning usb for storage devices... 0 Storage Device(s) found
>
>        scanning usb for ethernet devices... 1 Ethernet Device(s) found
>
> Hit any key to stop autoboot:  0
>
> U-Boot> setenv boot_targets us0 m0 x dc

This is missing characters.  You have have to type it out rather than
pasting it.

Should be "setenv boot_targets usb0 mmc0 pxe dhcp"

>
> U-Boot> saveenv
>
> Saving Environment to FAT...
>
> writing uboot.env
>
> FAT: Misaligned buffer address (000000003ab2ab50)
>
> sdhci_send_command: MMC: 0 busy timeout increasing to: 200 ms.
>
> done
>
> U-Boot> boot
>
> ## Error: "bootcmd_us0" not defined
>
> ## Error: "bootcmd_m0" not defined
>
> ## Error: "bootcmd_x" not defined
>
> ## Error: "bootcmd_dc" not defined
>
> U-Boot>
>
>
> -
> regards

Reply | Threaded
Open this post in threaded view
|

Re: near future (Rpi3)

Tuyosi Takesima
In reply to this post by Tuyosi Takesima
again i fail .
but someone can solve it .

i think micro SD in sd slot as CD , and micro SD in USB card reader as hard
disk .

--------------
# minicom -s

Welcome to minicom 2.7

OPTIONS: I18n
Compiled on Sep  6 2015, 19:49:19.
Port /dev/ttyUSB0, 11:52:24

Press CTRL-A Z for help on special keys



U-Boot 2017.03 (Apr 01 2017 - 04:27:09 -0600)

DRAM:  944 MiB
RPI 3 Model B (0xa02082)
MMC:   bcm2835_sdhci: 0
reading uboot.env

** Unable to read "uboot.env" from mmc0:1 **
Using default environment

In:    serial
Out:   lcd
Err:   lcd
Net:   Net Initialization Skipped
No ethernet found.
starting USB...
USB0:   Core Release: 2.80a
scanning bus 0 for devices...
      USB device not accepting new address (error=0)
3 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
       scanning usb for ethernet devices... 1 Ethernet Device(s) found
Hit any key to stop autoboot:  0
U-Boot> setenv boot_targets usb0 mmc0 pxe dhcp
U-Boot> saveenv
Saving Environment to FAT...
writing uboot.env
FAT: Misaligned buffer address (000000003ab2ab50)
sdhci_send_command: MMC: 0 busy timeout increasing to: 200 ms.
done
U-Boot> boot

USB device 0: unknown device
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found EFI removable media binary efi/boot/bootaa64.efi
reading efi/boot/bootaa64.efi
75737 bytes read in 68 ms (1.1 MiB/s)
## Starting EFI application at 01000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/arm64 BOOTAA64 0.2
boot>
booting sd0a:/bsd: 3735180+568620+500856+672776 [86+438216+232907]=0x7c2b70
[ using 672496 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved.
https://www.OpenBSD.org

OpenBSD 6.1-current (GENERIC) #0: Thu Apr  6 22:45:47 AEST 2017
    [hidden email]:/usr/src/sys/arch/arm64/compile/GENERIC
real mem  = 989855744 (944MB)
avail mem = 931606528 (888MB)
mainbus0 at root: Raspberry Pi 3 Model B Rev 1.2
simplefb0 at mainbus0: 656x416
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0 added (std, vt100 emulation)
simplebus0 at mainbus0: "soc"
bcmintc0 at simplebus0
bcmdog0 at simplebus0
pluart0 at simplebus0
com0 at simple�].�.r��6550, no workingcom0: console
dwctwo0 at simplebus0
agtimer0 at simplebus0: tick rate 19200 KHz
simplebus1 at mainbus0: "clocks"
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Broadcom DWC2 root hub" rev
2.00/1.00 addr 1
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems
product 0x9514" rev 2.00/2.2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 3
smsc0: address b8:27:eb:c3:cc:1a
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
umass0 at uhub1 port 2 configuration 1 interface 0 "Generic Mass Storage
Device" rev 2.00/1.00 addr 4
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Multi, Flash Reader, 1.00> SCSI0 0/direct
removable serial.058f6366051
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
panic: root device (22c292d19a866a8d) not found
Stopped at      panic+0x158:        TID    PID    UID     PRFLAGS
PFLAGS  C
PU  COMMAND
*     0      0      0     0x10000      0x200    0  swapper
Debugger() at panic+0x154
panic() at diskconf+0xac
diskconf() at main+0x46c
main() at $x.2+0x70
https://www.openbsd.org/ddb.html describes the minimum info required in bug
reports.  Insufficient info makes it difficult to find and fix bugs.
ddb>

-
regards