installation sets not found on CD

classic Classic list List threaded Threaded
11 messages Options
Reply | Threaded
Open this post in threaded view
|

installation sets not found on CD

Scott Stanley
Someone gave me a bunch of HP Proliant DL360 G3 servers, so I promptly
went to install 4.8 i386 on one to see if it was worth keeping.
(I'm just playing around at home with these)

Installer makes it all the way to installation set(s) location, then
kernel says:

ASC/ASCQ: ASC 0X20 ASCQ 0X00
cd0(atapiscsi0:0:0): Check condition (error 0x70) on opcode 0x20
SENSE KEY: Illegal Request
ASC/ASCQ: ASC 0X20 ASCQ 0X00

followed by installer saying:

No filesystems found on cd0


This fellow had the same issue, and there was no resolution that I could see.
http://www.mail-archive.com/misc@.../msg50451.html

My attempt was done using an official i386 disc that has installed 4.8
on 2 other systems, so I know the disc is good. OR, is there a
possibility that the disc is marginal and the drive is picky enough to
complain? I tried this on 3 or 4 of the systems and got the same
error.

Is there any more information I can provide for clues to help?

-Scott

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

Joachim Schipper-2
On Mon, Nov 29, 2010 at 06:52:38PM -0800, Scott Stanley wrote:

> Someone gave me a bunch of HP Proliant DL360 G3 servers, so I promptly
> went to install 4.8 i386 on one to see if it was worth keeping.
> (I'm just playing around at home with these)
>
> Installer makes it all the way to installation set(s) location, then
> kernel says:
>
> ASC/ASCQ: ASC 0X20 ASCQ 0X00
> cd0(atapiscsi0:0:0): Check condition (error 0x70) on opcode 0x20
> SENSE KEY: Illegal Request
> ASC/ASCQ: ASC 0X20 ASCQ 0X00
>
> followed by installer saying:
>
> No filesystems found on cd0
>
>
> This fellow had the same issue, and there was no resolution that I could see.
> http://www.mail-archive.com/misc@.../msg50451.html
>
> My attempt was done using an official i386 disc that has installed 4.8
> on 2 other systems, so I know the disc is good. OR, is there a
> possibility that the disc is marginal and the drive is picky enough to
> complain? I tried this on 3 or 4 of the systems and got the same
> error.
>
> Is there any more information I can provide for clues to help?

Can't you install via PXE? It's possible that the CD drive is broken or
unsupported (although I wouldn't expect the latter to be the case), but
that shouldn't prevent you from installing OpenBSD. And a full system
may make diagnosis easier...

                Joachim

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

Kevin Chadwick-2
In reply to this post by Scott Stanley
On Mon, 29 Nov 2010 18:52:38 -0800
Scott Stanley <[hidden email]> wrote:

>  OR, is there a
> possibility that the disc is marginal and the drive is picky enough to
> complain?

This has happened to me twice, once a retry worked the other time I
plugged in a usb-to-ide cdrom and the installer picked it up straight
away with no fiddling.

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

L. V. Lammert
In reply to this post by Joachim Schipper-2
On Tue, 30 Nov 2010, Joachim Schipper wrote:

> On Mon, Nov 29, 2010 at 06:52:38PM -0800, Scott Stanley wrote:
> >
> > Installer makes it all the way to installation set(s) location, then
> > kernel says:
> >
> > ASC/ASCQ: ASC 0X20 ASCQ 0X00
> > cd0(atapiscsi0:0:0): Check condition (error 0x70) on opcode 0x20
> > SENSE KEY: Illegal Request
> > ASC/ASCQ: ASC 0X20 ASCQ 0X00
> >
If you're having problems with the CD drive, why not mount or copy the  CD
on another machine and install via ftp??

        Lee

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

Raimo Niskanen-7
On Tue, Nov 30, 2010 at 08:27:25AM -0600, L. V. Lammert wrote:

> On Tue, 30 Nov 2010, Joachim Schipper wrote:
>
> > On Mon, Nov 29, 2010 at 06:52:38PM -0800, Scott Stanley wrote:
> > >
> > > Installer makes it all the way to installation set(s) location, then
> > > kernel says:
> > >
> > > ASC/ASCQ: ASC 0X20 ASCQ 0X00
> > > cd0(atapiscsi0:0:0): Check condition (error 0x70) on opcode 0x20
> > > SENSE KEY: Illegal Request
> > > ASC/ASCQ: ASC 0X20 ASCQ 0X00
> > >
> If you're having problems with the CD drive, why not mount or copy the  CD
> on another machine and install via ftp??

... or put the set(s) on a USB stick, if the machine reads such...

>
> Lee

--

/ Raimo Niskanen, Erlang/OTP, Ericsson AB

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

LeviaComm Networks NOC
In reply to this post by Scott Stanley
On 29-Nov-10 18:52, Scott Stanley wrote:

> Someone gave me a bunch of HP Proliant DL360 G3 servers, so I promptly
> went to install 4.8 i386 on one to see if it was worth keeping.
> (I'm just playing around at home with these)
>
> Installer makes it all the way to installation set(s) location, then
> kernel says:
>
> ASC/ASCQ: ASC 0X20 ASCQ 0X00
> cd0(atapiscsi0:0:0): Check condition (error 0x70) on opcode 0x20
> SENSE KEY: Illegal Request
> ASC/ASCQ: ASC 0X20 ASCQ 0X00
>
> followed by installer saying:
>
> No filesystems found on cd0
>
>
> This fellow had the same issue, and there was no resolution that I could see.
> http://www.mail-archive.com/misc@.../msg50451.html
>
> My attempt was done using an official i386 disc that has installed 4.8
> on 2 other systems, so I know the disc is good. OR, is there a
> possibility that the disc is marginal and the drive is picky enough to
> complain? I tried this on 3 or 4 of the systems and got the same
> error.
>
> Is there any more information I can provide for clues to help?
>
> -Scott
>
>

What CD-ROM drive do you have installed on these systems?  The 360 G3s
shipped with a couple different models, some are excellent units, others
are complete crap.

You may also try ejecting the drive and re-inserting it.  Some
production runs of the 360s weren't constructed properly and the IDE
backplane will fail.

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

Scott Stanley
just for the record (for future googlers):
I dusted off my CD, tried again; no luck.
while still in the installer (set installation phase):
-removed CD
-copied the /4.8/i386 directory from CD onto a flash drive on another machine
-replaced CD and plugged in usb
-pointed the installer to the usb directory
this was by far the quickest, easiest workaround; thank you Raimo.

just a bit of extra verbosity:
I had the OS set to "OTHER" in BIOS, and kernel panicked (bsd.mp). Set
the BIOS to LINUX and it boots. That's just a comment though, not
looking for help on this, and not assuming this workaround is exactly
successful until I can read up on it.


thank you all for the replies. had I more time I would have turned
this into a "science project". over and out.

-Scott

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

Scott Stanley
> Once you have installed the system, think about posting the "cd0" relevant
> part of the dmesg too, or better together with the complete dmesg output.
> That will help developers and future googlers even more.
>
> Has the readability of the CD-ROM changed? And with different CD-ROMs? Could
> also be important for them to know.

I'll do that David.
As far as the CD goes, here's my observation (I'll no make any conclusions):

-installation from CD started successfully, up to point of installing sets
-sets directory copied from CD to flash drive, assumed complete and
correct (installer used copied data to install sets)
-installer completed successfully. CD had been re-inserted, but I
guess everything is in RAM, so the point is probably moot

I'll post a dmesg and do some digging myself after a few days, if
nothing else to wrap up this thread.

-Scott

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

roberth-5
On Wed, 1 Dec 2010 07:46:57 -0800
Scott Stanley <[hidden email]> wrote:

> -installation from CD started successfully, up to point of installing
> sets -sets directory copied from CD to flash drive, assumed complete
> and correct (installer used copied data to install sets)
> -installer completed successfully. CD had been re-inserted, but I
> guess everything is in RAM, so the point is probably moot

Just to make sure, you copied the sets to the usbdrive on a different
system, right?

fyi, bsd.rd can even be sucessfully loaded from an external vaio
firewire dvd drive. This step is totally seperate from OpenBSD itself.

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

Steven Surdock
In reply to this post by Scott Stanley
> -----Original Message-----
> From: [hidden email] [mailto:[hidden email]] On Behalf
Of
> Scott Stanley
> Sent: Wednesday, December 01, 2010 10:47 AM
> To: OpenBSD
> Subject: Re: installation sets not found on CD
>
...
> As far as the CD goes, here's my observation (I'll no make any
> conclusions):
>
> -installation from CD started successfully, up to point of installing
sets
> -sets directory copied from CD to flash drive, assumed complete and
> correct (installer used copied data to install sets) -installer
completed
> successfully. CD had been re-inserted, but I guess everything is in
RAM,
> so the point is probably moot
>

Interesting, I recently installed 4.8-stable (from a custom built
CD-ROM) on a couple of Compaq DL360s G2's that locked up when trying to
read the install sets off the CD.  It booted bds.rd fine. I ended up
installing sets via http.  I assumed a bad CD Drive on the first system.
The second one was a bit too coincidental.  Here is the dmesg:

OpenBSD 4.8-stable (GENERIC) #0: Mon Oct 25 13:02:04 EDT 2010

[hidden email]:/usr/src/sys/arch/i386/compil
e/GENERIC
cpu0: Intel(R) Pentium(R) III CPU - S 1400MHz ("GenuineIntel" 686-class)
1.40 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,
FXSR,SSE
real mem  = 267984896 (255MB)
avail mem = 253644800 (241MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000,
SMBIOS rev. 2.3 @ 0xec000 (33 entries)
bios0: vendor Compaq version "P26" date 06/25/2002
bios0: Compaq ProLiant DL360 G2
acpi0 at bios0: rev 0
acpi0: sleep states S0 S4 S5, can't enable ACPI
mpbios0 at bios0: Intel MP Specification 1.4
cpu0 at mainbus0: apid 3 (boot processor)
cpu0: apic clock running at 132MHz
mpbios0: bus 0 is type PCI
mpbios0: bus 1 is type PCI
mpbios0: bus 7 is type PCI
mpbios0: bus 15 is type ISA
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 11, 16 pins
ioapic0: misconfigured as apic 2, remapped to apid 8
ioapic1 at mainbus0: apid 2 pa 0xfec01000, version 11, 16 pins
ioapic1: misconfigured as apic 3, remapped to apid 2
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x4000 0xcc000/0x1800
0xee000/0x2000!
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20HE Host" rev 0x23
pci1 at pchb0 bus 1
ciss0 at pci1 dev 4 function 0 "Compaq Smart Array 5i/532 rev.2" rev
0x01: apic 2 int 15 (irq 11)
ciss0: 1 LD, HW rev 1, FW 2.66/2.66
scsibus0 at ciss0: 1 targets
sd0 at scsibus0 targ 0 lun 0: <COMPAQ, LOGICAL VOLUME, 2.66> SCSI0
0/direct fixed
sd0: 17359MB, 512 bytes/sec, 35553120 sec total
bge0 at pci1 dev 5 function 0 "Broadcom BCM5701" rev 0x15, BCM5701 B5
(0x105): apic 2 int 14 (irq 5), address 00:08:02:a3:e7:1b
brgphy0 at bge0 phy 1: BCM5701 10/100/1000baseT PHY, rev. 0
bge1 at pci1 dev 6 function 0 "Broadcom BCM5701" rev 0x15, BCM5701 B5
(0x105): apic 2 int 13 (irq 10), address 00:08:02:a3:e7:31
brgphy1 at bge1 phy 1: BCM5701 10/100/1000baseT PHY, rev. 0
pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20HE Host" rev 0x01
pchb2 at pci0 dev 0 function 2 "ServerWorks CNB20HE Host" rev 0x01
pchb3 at pci0 dev 0 function 3 "ServerWorks CNB20HE Host" rev 0x01
pci2 at pchb3 bus 7
ppb0 at pci2 dev 6 function 0 "Intel 21154AE/BE PCI-PCI" rev 0x00
pci3 at ppb0 bus 8
fxp0 at pci3 dev 4 function 0 "Intel 8255x" rev 0x08, i82559: apic 2 int
10 (irq 15), address 00:08:02:ff:b6:3a
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
fxp1 at pci3 dev 5 function 0 "Intel 8255x" rev 0x08, i82559: apic 2 int
9 (irq 10), address 00:08:02:ff:b6:3b
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
vga1 at pci0 dev 3 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Compaq iLO" rev 0x01 at pci0 dev 5 function 0 not configured
"Compaq iLO" rev 0x01 at pci0 dev 5 function 2 not configured
piixpm0 at pci0 dev 15 function 0 "ServerWorks CSB5" rev 0x92: polling
iic0 at piixpm0
thmc0 at iic0 addr 0x2c: adm1022
iic0: addr 0x2d 13=47 14=4c 15=02 17=46 18=64 20=80 26=80 27=30 2b=7f
2c=80 37=49 38=c9 39=44 3a=c9 3e=41 3f=c1 40=2b 41=b0 43=b6 44=00 47=50
4a=01 4c=b0 93=47 94=4c 95=02 97=46 98=64 a0=80 a6=80 a7=30 ab=7f ac=80
b7=49 b8=c9 b9=44 ba=c9 be=41 bf=c1 c0=2b c1=10 c3=b6 c4=00 c7=50 ca=01
cc=10 words 00=ffff 01=ffff 02=ffff 03=ffff 04=ffff 05=ffff 06=ffff
07=ffff
spdmem0 at iic0 addr 0x51: 128MB SDRAM registered ECC PC133CL2
spdmem1 at iic0 addr 0x52: 128MB SDRAM registered ECC PC133CL2
pciide0 at pci0 dev 15 function 1 "ServerWorks CSB5 IDE" rev 0x92: DMA
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <COMPAQ, CD-224E, A.8D> ATAPI 5/cdrom
removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2
ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev 0x05:
apic 8 int 7 (irq 7), version 1.0, legacy support
pchb4 at pci0 dev 15 function 3 "ServerWorks CSB5 LPC" rev 0x00
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "ServerWorks OHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
mtrr: Pentium Pro MTRR support
uhidev0 at uhub0 port 4 configuration 1 interface 0 "Dell Dell USB
Keyboard" rev 1.10/3.01 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
softraid0 at root
root on sd0a swap on sd0b dump on sd0b

Reply | Threaded
Open this post in threaded view
|

Re: installation sets not found on CD

Rod Whitworth-3
On Thu, 2 Dec 2010 01:22:06 -0500, Steven Surdock wrote:

>Interesting, I recently installed 4.8-stable (from a custom built
>CD-ROM) on a couple of Compaq DL360s G2's that locked up when trying to
>read the install sets off the CD.  It booted bds.rd fine. I ended up
>installing sets via http.  I assumed a bad CD Drive on the first system.
>The second one was a bit too coincidental.  Here is the dmesg:
8><----snip

Donkey's ages ago I tried to install a later release than was then
running on a client's firewall. It booted off the CD but was no-go
after.

I put a full dmesg in a query to misc and tedu had a patch waiting for
me when I got up next morning. I don't remember the grisly details but
maybe he does.

The client was mightily impressed and I remember sending some Aussie
calendars etc to Ted. I wsh for your sake I remembered the cause of the
problem. I could be persuaded it was to do with the model of CD drive
but maybe old-timers is setting in.

Good luck!

*** NOTE *** Please DO NOT CC me. I <am> subscribed to the list.
Mail to the sender address that does not originate at the list server is tarpitted. The reply-to: address is provided for those who feel compelled to reply off list. Thankyou.

Rod/
---
This life is not the real thing.
It is not even in Beta.
If it was, then OpenBSD would already have a man page for it.