ath0: unable to reset hardware - on latest snapshot

classic Classic list List threaded Threaded
1 message Options
Reply | Threaded
Open this post in threaded view

ath0: unable to reset hardware - on latest snapshot

Stefan Kaltenbrunner
Hi all!

trying to use my ath(4) based Netgear WG511U on an older IBM notebook
results in:

ar5k_ar5212_nic_wakeup: failed to resume the AR5212 (again)
ath0: unable to reset hardware; hal status 3633405228

as soon as I try to configure anything through ifconfig (like setting
nwid or mode/mediaopts).

dmesg of the box follows:


OpenBSD 3.8-current (GENERIC) #572: Wed Jan 11 01:04:56 MST 2006
    [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 232 MHz
real mem  = 100048896 (97704K)
avail mem = 84041728 (82072K)
using 1246 buffers containing 5103616 bytes (4984K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(54) BIOS, date 09/11/98, BIOS32 rev. 0 @ 0xfd820
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd880/0x800
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfb150/96 (4 entries)
pcibios0: PCI Exclusive IRQs: 11
pcibios0: PCI Interrupt Router at 000:06:0 ("Intel 82371AB PIIX4 ISA"
rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xa000
ipmi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX" rev 0x02
cbb0 at pci0 dev 2 function 0 "Texas Instruments PCI1250 CardBus" rev
0x02: irq 11
cbb1 at pci0 dev 2 function 1 "Texas Instruments PCI1250 CardBus" rev
0x02: irq 11
vga1 at pci0 dev 3 function 0 "Neomagic Magicgraph NM2160" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 6 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01
pciide0 at pci0 dev 6 function 1 "Intel 82371AB IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DTCA-24090>
wd0: 16-sector PIO, LBA, 3909MB, 8007552 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SANYO, CRD-S372B, 1.24> SCSI0 5/cdrom
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
cd0(pciide0:0:1): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
uhci0 at pci0 dev 6 function 2 "Intel 82371AB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 6 function 3 "Intel 82371AB Power" rev 0x01: SMI
iic0 at piixpm0
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x8, lattimer 0xb0
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 2 device 0 cacheline 0x8, lattimer 0xb0
pcmcia1 at cardslot1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
sb0 at isa0 port 0x220/24 irq 5 drq 1: dsp v3.02
midi0 at sb0: <SB MIDI UART>
audio0 at sb0
opl0 at sb0: model OPL3
midi1 at opl0: <SB Yamaha OPL3>
pcppi0 at isa0 port 0x61
midi2 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt2 at isa0 port 0x3bc/4: polled
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask efcd netmask efcd ttymask ffcf
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
ne3 at pcmcia1 function 0 "D-Link, DE-660, 118B6603" port 0xa000/32,
address 00:80:c8:8c:af:6a
ath0 at cardbus0 dev 0 function 0 "Atheros Communications, Inc.,
AR5001-0000-0000, Wireless LAN Reference Card": irq 11
ath0: AR5213 5.9 phy 4.3 rf5112 3.6, FCC2A*, address 00:0f:b5:3d:db:f5
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302