Who runs OpenBSD with Adaptec ?

classic Classic list List threaded Threaded
4 messages Options
Reply | Threaded
Open this post in threaded view
|

Who runs OpenBSD with Adaptec ?

Ricardo Augusto de Souza
Hi,



I AM trying to install openBSD 4.4 on a IBM 3550 7978 B1U but OpenBSD didn4t
recognize Adaptec ServeRaid 8k.



I4d like to know if someone run it on a server with this raid controller.



I installed a custom openbsd kernel ( with aac* support)  on  a USB stick ,
boot it on IBM 3550 and this is the dmesg:

I also tried disabling acpi.



OpenBSD 4.4 (rox) #0: Wed Apr  8 16:27:08 BRT 2009

    root@Tux:/usr/sys/arch/i386/compile/rox

cpu0: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz ("GenuineIntel" 686-class) 2
GHz

cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,CX16,
xTPR

real mem  = 2137350144 (2038MB)

avail mem = 2058268672 (1962MB)

mainbus0 at root

bios0 at mainbus0: AT/286+ BIOS, date 07/25/08, BIOS32 rev. 0 @ 0xffa10,
SMBIOS rev. 2.4 @ 0xf6be0 (62 entries)

bios0: vendor Dell Inc. version "A07" date 07/25/2008

bios0: Dell Inc. Latitude D530

acpi0 at bios0: rev 2

acpi0: tables DSDT FACP HPET APIC ASF! MCFG TCPA SLIC SSDT

acpi0: wakeup devices PCI0(S5) PCIE(S4) USB1(S0) USB2(S0) USB3(S0) USB4(S0)
USB5(S0) EHC2(S0) EHCI(S0) AZAL(S3) RP01(S3) RP02(S4) RP03(S3) RP04(S3)
RP05(S3) RP06(S5) LID_(S3) PBTN(S4)

acpitimer0 at acpi0: 3579545 Hz, 24 bits

acpihpet0 at acpi0: 14318179 Hz

acpiprt0 at acpi0: bus 3 (PCIE)

acpiprt1 at acpi0: bus -1 (AGP_)

acpiprt2 at acpi0: bus 11 (RP01)

acpiprt3 at acpi0: bus 12 (RP02)

acpiprt4 at acpi0: bus -1 (RP03)

acpiprt5 at acpi0: bus -1 (RP04)

acpiprt6 at acpi0: bus -1 (RP05)

acpiprt7 at acpi0: bus 9 (RP06)

acpiprt8 at acpi0: bus 0 (PCI0)

acpicpu0 at acpi0: C3

acpitz0 at acpi0: critical temperature 99 degC

acpibtn0 at acpi0: LID_

acpibtn1 at acpi0: PBTN

acpibtn2 at acpi0: SBTN

acpiac0 at acpi0: AC unit offline

acpibat0 at acpi0: BAT0 model "DELL TT7108" serial 4001 type LION oem "Sanyo"

acpibat1 at acpi0: BAT1 not present

acpidock at acpi0 not configured

acpivideo at acpi0 not configured

acpivideo at acpi0 not configured

acpivideo at acpi0 not configured

bios0: ROM list: 0xc0000/0xf000! 0xcf000/0x1000

cpu0 at mainbus0

cpu0: unknown Enhanced SpeedStep CPU, msr 0x06170b2d06000a25

cpu0: using only highest, current and lowest power states

cpu0: Enhanced SpeedStep 2000 MHz (1292 mV): speeds: 2200, 2000, 1200 MHz

pci0 at mainbus0 bus 0: configuration mode 1 (no bios)

pchb0 at pci0 dev 0 function 0 "Intel GM965 Host" rev 0x0c

vga1 at pci0 dev 2 function 0 "Intel GM965 Video" rev 0x0c

wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)

wsdisplay0: screen 1-5 added (80x25, vt100 emulation)

agp0 at vga1: aperture at 0xe0000000, size 0x10000000

drm at vga1 unsupported

"Intel GM965 Video" rev 0x0c at pci0 dev 2 function 1 not configured

uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x02: irq 10

uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x02: irq 9

ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x02: irq 5

usb0 at ehci0: USB revision 2.0

uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1

azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x02: irq 9

azalia0: codec[s]: Sigmatel/0x76a0, Conexant/0x2c06, using Sigmatel/0x76a0

audio0 at azalia0

ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x02: irq 11

pci1 at ppb0 bus 11

ppb1 at pci0 dev 28 function 1 "Intel 82801H PCIE" rev 0x02: irq 3

pci2 at ppb1 bus 12

wpi0 at pci2 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02: irq 3,
MoW2, address 00:1f:3c:bf:c0:9d

ppb2 at pci0 dev 28 function 5 "Intel 82801H PCIE" rev 0x02: irq 3

pci3 at ppb2 bus 9

bge0 at pci3 dev 0 function 0 "Broadcom BCM5755M" rev 0x02, BCM5755 A2
(0xa002): irq 3, address 00:1e:c9:23:04:f0

brgphy0 at bge0 phy 1: BCM5755 10/100/1000baseT PHY, rev. 0

uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x02: irq 10

uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x02: irq 9

uhci4 at pci0 dev 29 function 2 "Intel 82801H USB" rev 0x02: irq 5

ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x02: irq 10

usb1 at ehci1: USB revision 2.0

uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1

ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xf2

pci4 at ppb3 bus 3

cbb0 at pci4 dev 1 function 0 vendor "O2 Micro", unknown product 0x7135 rev
0x21: irq 11

"O2 Micro Firewire" rev 0x02 at pci4 dev 1 function 4 not configured

cardslot0 at cbb0 slot 0 flags 0

cardbus0 at cardslot0: bus 4 device 0 cacheline 0x0, lattimer 0x20

pcmcia0 at cardslot0

ichpcib0 at pci0 dev 31 function 0 "Intel 82801HBM LPC" rev 0x02: PM disabled

pciide0 at pci0 dev 31 function 1 "Intel 82801HBM IDE" rev 0x02: DMA, channel
0 configured to compatibility, channel 1 configured to compatibility

atapiscsi0 at pciide0 channel 0 drive 0

scsibus0 at atapiscsi0: 2 targets, initiator 7

cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVD+-RW GSA-T21N, A1R1> ATAPI 5/cdrom
removable

cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2

pciide0: channel 1 ignored (disabled)

pciide1 at pci0 dev 31 function 2 "Intel 82801HBM SATA" rev 0x02: DMA, channel
0 configured to native-PCI, channel 1 configured to native-PCI

pciide1: using irq 10 for native-PCI interrupt

wd0 at pciide1 channel 0 drive 0: <FUJITSU MHZ2080BH G2>

wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors

wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5

ichiic0 at pci0 dev 31 function 3 "Intel 82801H SMBus" rev 0x02: SMI

iic0 at ichiic0

spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM

spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM

usb2 at uhci0: USB revision 1.0

uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb3 at uhci1: USB revision 1.0

uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb4 at uhci2: USB revision 1.0

uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb5 at uhci3: USB revision 1.0

uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb6 at uhci4: USB revision 1.0

uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1

isa0 at ichpcib0

isadma0 at isa0

com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo

pckbc0 at isa0 port 0x60/5

pckbd0 at pckbc0 (kbd slot)

pckbc0: using irq 1 for kbd slot

wskbd0 at pckbd0: console keyboard, using wsdisplay0

pms0 at pckbc0 (aux slot)

pckbc0: using irq 12 for aux slot

wsmouse0 at pms0 mux 0

pcppi0 at isa0 port 0x61

midi0 at pcppi0: <PC speaker>

spkr0 at pcppi0

npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16

biomask efe5 netmask efed ttymask ffff

mtrr: Pentium Pro MTRR support

umass0 at uhub1 port 1 configuration 1 interface 0 "Kingston DataTraveler 2.0"
rev 2.00/2.00 addr 2

umass0: using SCSI over Bulk-Only

scsibus1 at umass0: 2 targets, initiator 0

sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2
0/direct removable

sd0: 3858MB, 491 cyl, 255 head, 63 sec, 512 bytes/sec, 7902208 sec total

softraid0 at root

root on sd0a swap on sd0b dump on sd0b



FreeBSD 7.14s dmesg:

aac0: <IBM ServeRAID-8k> port 0x4000-0x40ff mem
0xcce00000-0xccffffff,0xcafe0000-0xcaffffff irq 17 at device 0.0 on pci2

aac0: Enable Raw I/O

aac0: Enable 64-bit array

aac0: New comm. interface enabled

aac0: [ITHREAD]

aac0: ServeRAID 8k-l  , aac driver 2.0.0-1





;((((

Reply | Threaded
Open this post in threaded view
|

RES: Who runs OpenBSD with Adaptec ?

Ricardo Augusto de Souza
I sent dmesg of my notebook. Sorry.

OpenBSD 4.4 (rox) #0: Wed Apr  8 16:27:08 BRT 2009
    root@Tux:/usr/sys/arch/i386/compile/rox
cpu0: Intel(R) Xeon(R) CPU E5405 @ 2.00GHz ("GenuineIntel" 686-class) 2
GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,TM2
,CX16,xTPR
real mem  = 2952105984 (2815MB)
avail mem = 2856112128 (2723MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/29/09, BIOS32 rev. 0 @ 0xfd841,
SMBIOS rev. 2.4 @ 0xaffcee80 (86 entries)
bios0: vendor IBM version "-[GFE143AUS-1.13]-" date 01/29/2009
bios0: IBM IBM System x3550 -[7978B1U]-
acpi0 at bios0: rev 2
acpi0: tables DSDT FACP APIC SRAT HPET MCFG ERST
acpi0: wakeup devices PCI0(S5)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 19 (PCI6)
acpiprt1 at acpi0: bus 23 (PCIA)
acpiprt2 at acpi0: bus 1 (PCIS)
acpiprt3 at acpi0: bus 0 (PCI0)
acpicpu0 at acpi0
bios0: ROM list: 0xc0000/0xb000 0xcb000/0x1800 0xcc800/0x1800
0xce000/0x5000!
ipmi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 5000X Host" rev 0x31
ppb0 at pci0 dev 2 function 0 "Intel 5000 PCIE x8" rev 0x31
pci1 at ppb0 bus 16
ppb1 at pci1 dev 0 function 0 "Intel 6321ESB PCIE" rev 0x01
pci2 at ppb1 bus 17
ppb2 at pci2 dev 0 function 0 "Intel 6321ESB PCIE" rev 0x01
pci3 at ppb2 bus 19
ppb3 at pci3 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
0x04
pci4 at ppb3 bus 20
ppb4 at pci4 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
0x04
pci5 at ppb4 bus 21
em0 at pci5 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
3, address 00:15:17:7b:9a:b0
em1 at pci5 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
10, address 00:15:17:7b:9a:b1
ppb5 at pci4 dev 1 function 0 vendor "IDT", unknown product 0x8018 rev
0x04
pci6 at ppb5 bus 22
em2 at pci6 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
10, address 00:15:17:7b:9a:b2
em3 at pci6 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
7, address 00:15:17:7b:9a:b3
ppb6 at pci2 dev 1 function 0 "Intel 6321ESB PCIE" rev 0x01
pci7 at ppb6 bus 18
ppb7 at pci1 dev 0 function 3 "Intel 6321ESB PCIE-PCIX" rev 0x01
pci8 at ppb7 bus 23
ppb8 at pci0 dev 3 function 0 "Intel 5000 PCIE" rev 0x31
pci9 at ppb8 bus 35
ppb9 at pci0 dev 4 function 0 "Intel 5000 PCIE x8" rev 0x31
pci10 at ppb9 bus 7
ppb10 at pci10 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
0x04
pci11 at ppb10 bus 8
ppb11 at pci11 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
0x04
pci12 at ppb11 bus 9
em4 at pci12 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06:
irq 7, address 00:15:17:7b:be:f0
em5 at pci12 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06:
irq 3, address 00:15:17:7b:be:f1
ppb12 at pci11 dev 1 function 0 vendor "IDT", unknown product 0x8018 rev
0x04
pci13 at ppb12 bus 10
em6 at pci13 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06:
irq 3, address 00:15:17:7b:be:f2
em7 at pci13 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06:
irq 10, address 00:15:17:7b:be:f3
ppb13 at pci0 dev 5 function 0 "Intel 5000 PCIE" rev 0x31
pci14 at ppb13 bus 34
ppb14 at pci0 dev 6 function 0 "Intel 5000 PCIE" rev 0x31
pci15 at ppb14 bus 3
ppb15 at pci15 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xc3
pci16 at ppb15 bus 4
bnx0 at pci16 dev 0 function 0 "Broadcom BCM5708" rev 0x12: irq 7
ppb16 at pci0 dev 7 function 0 "Intel 5000 PCIE" rev 0x31
pci17 at ppb16 bus 2
"Adaptec ASR-2120S" rev 0x02 at pci17 dev 0 function 0 not configured
"Intel I/OAT" rev 0x31 at pci0 dev 8 function 0 not configured
pchb1 at pci0 dev 16 function 0 "Intel 5000 Error Reporting" rev 0x31
pchb2 at pci0 dev 16 function 1 "Intel 5000 Error Reporting" rev 0x31
pchb3 at pci0 dev 16 function 2 "Intel 5000 Error Reporting" rev 0x31
pchb4 at pci0 dev 17 function 0 "Intel 5000 Reserved" rev 0x31
pchb5 at pci0 dev 19 function 0 "Intel 5000 Reserved" rev 0x31
pchb6 at pci0 dev 21 function 0 "Intel 5000 FBD" rev 0x31
pchb7 at pci0 dev 22 function 0 "Intel 5000 FBD" rev 0x31
ppb17 at pci0 dev 28 function 0 "Intel 6321ESB PCIE" rev 0x09
pci18 at ppb17 bus 5
ppb18 at pci18 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xc3
pci19 at ppb18 bus 6
bnx1 at pci19 dev 0 function 0 "Broadcom BCM5708" rev 0x12: irq 3
uhci0 at pci0 dev 29 function 0 "Intel 6321ESB USB" rev 0x09: irq 5
uhci1 at pci0 dev 29 function 1 "Intel 6321ESB USB" rev 0x09: irq 11
uhci2 at pci0 dev 29 function 2 "Intel 6321ESB USB" rev 0x09: irq 5
ehci0 at pci0 dev 29 function 7 "Intel 6321ESB USB" rev 0x09: irq 5
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb19 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xd9
pci20 at ppb19 bus 1
vga1 at pci20 dev 1 function 0 "ATI ES1000" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
drm at vga1 unsupported
ichpcib0 at pci0 dev 31 function 0 "Intel 6321ESB LPC" rev 0x09: PM
disabled
pciide0 at pci0 dev 31 function 1 "Intel 6321ESB IDE" rev 0x09: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, RW/DVD GCC-T10N, 1.00> ATAPI
5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ichiic0 at pci0 dev 31 function 3 "Intel 6321ESB SMBus" rev 0x09:
polling
iic0 at ichiic0
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
biomask f965 netmask fded ttymask ffff
mtrr: Pentium Pro MTRR support
umass0 at uhub0 port 3 configuration 1 interface 0 "Kingston
DataTraveler 2.0" rev 2.00/2.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2
0/direct removable
sd0: 3858MB, 491 cyl, 255 head, 63 sec, 512 bytes/sec, 7902208 sec total
uhub4 at uhub2 port 2 "Silitek IBM USB HUB KEYBOARD" rev 1.10/1.00 addr
2
uhidev0 at uhub4 port 1 configuration 1 interface 0 "Silitek IBM USB HUB
KEYBOARD" rev 1.10/1.00 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 3 configuration 1 interface 0 "vendor 0x15ca USB
Optical Mouse" rev 2.00/5.12 addr 4
uhidev1: iclass 3/1
ums0 at uhidev1: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
softraid0 at root
root on sd0a swap on sd0b dump on sd0b
bnx1: address 00:1a:64:79:f1:5a
brgphy0 at bnx1 phy 1: BCM5708C 10/100/1000baseT PHY, rev. 6
bnx0: address 00:1a:64:79:f1:58
brgphy1 at bnx0 phy 1: BCM5708C 10/100/1000baseT PHY, rev. 6

-----Mensagem original-----
De: [hidden email] [mailto:[hidden email]] Em nome de
Ricardo Augusto de Souza
Enviada em: quinta-feira, 9 de abril de 2009 18:16
Para: [hidden email]
Assunto: Who runs OpenBSD with Adaptec ?

Hi,



I AM trying to install openBSD 4.4 on a IBM 3550 7978 B1U but OpenBSD
didn4t
recognize Adaptec ServeRaid 8k.



I4d like to know if someone run it on a server with this raid
controller.



I installed a custom openbsd kernel ( with aac* support)  on  a USB
stick ,
boot it on IBM 3550 and this is the dmesg:

I also tried disabling acpi.



OpenBSD 4.4 (rox) #0: Wed Apr  8 16:27:08 BRT 2009

    root@Tux:/usr/sys/arch/i386/compile/rox

cpu0: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz ("GenuineIntel"
686-class) 2
GHz

cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,
CX16,
xTPR

real mem  = 2137350144 (2038MB)

avail mem = 2058268672 (1962MB)

mainbus0 at root

bios0 at mainbus0: AT/286+ BIOS, date 07/25/08, BIOS32 rev. 0 @ 0xffa10,
SMBIOS rev. 2.4 @ 0xf6be0 (62 entries)

bios0: vendor Dell Inc. version "A07" date 07/25/2008

bios0: Dell Inc. Latitude D530

acpi0 at bios0: rev 2

acpi0: tables DSDT FACP HPET APIC ASF! MCFG TCPA SLIC SSDT

acpi0: wakeup devices PCI0(S5) PCIE(S4) USB1(S0) USB2(S0) USB3(S0)
USB4(S0)
USB5(S0) EHC2(S0) EHCI(S0) AZAL(S3) RP01(S3) RP02(S4) RP03(S3) RP04(S3)
RP05(S3) RP06(S5) LID_(S3) PBTN(S4)

acpitimer0 at acpi0: 3579545 Hz, 24 bits

acpihpet0 at acpi0: 14318179 Hz

acpiprt0 at acpi0: bus 3 (PCIE)

acpiprt1 at acpi0: bus -1 (AGP_)

acpiprt2 at acpi0: bus 11 (RP01)

acpiprt3 at acpi0: bus 12 (RP02)

acpiprt4 at acpi0: bus -1 (RP03)

acpiprt5 at acpi0: bus -1 (RP04)

acpiprt6 at acpi0: bus -1 (RP05)

acpiprt7 at acpi0: bus 9 (RP06)

acpiprt8 at acpi0: bus 0 (PCI0)

acpicpu0 at acpi0: C3

acpitz0 at acpi0: critical temperature 99 degC

acpibtn0 at acpi0: LID_

acpibtn1 at acpi0: PBTN

acpibtn2 at acpi0: SBTN

acpiac0 at acpi0: AC unit offline

acpibat0 at acpi0: BAT0 model "DELL TT7108" serial 4001 type LION oem
"Sanyo"

acpibat1 at acpi0: BAT1 not present

acpidock at acpi0 not configured

acpivideo at acpi0 not configured

acpivideo at acpi0 not configured

acpivideo at acpi0 not configured

bios0: ROM list: 0xc0000/0xf000! 0xcf000/0x1000

cpu0 at mainbus0

cpu0: unknown Enhanced SpeedStep CPU, msr 0x06170b2d06000a25

cpu0: using only highest, current and lowest power states

cpu0: Enhanced SpeedStep 2000 MHz (1292 mV): speeds: 2200, 2000, 1200
MHz

pci0 at mainbus0 bus 0: configuration mode 1 (no bios)

pchb0 at pci0 dev 0 function 0 "Intel GM965 Host" rev 0x0c

vga1 at pci0 dev 2 function 0 "Intel GM965 Video" rev 0x0c

wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)

wsdisplay0: screen 1-5 added (80x25, vt100 emulation)

agp0 at vga1: aperture at 0xe0000000, size 0x10000000

drm at vga1 unsupported

"Intel GM965 Video" rev 0x0c at pci0 dev 2 function 1 not configured

uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x02: irq 10

uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x02: irq 9

ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x02: irq 5

usb0 at ehci0: USB revision 2.0

uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1

azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x02: irq
9

azalia0: codec[s]: Sigmatel/0x76a0, Conexant/0x2c06, using
Sigmatel/0x76a0

audio0 at azalia0

ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x02: irq 11

pci1 at ppb0 bus 11

ppb1 at pci0 dev 28 function 1 "Intel 82801H PCIE" rev 0x02: irq 3

pci2 at ppb1 bus 12

wpi0 at pci2 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02: irq
3,
MoW2, address 00:1f:3c:bf:c0:9d

ppb2 at pci0 dev 28 function 5 "Intel 82801H PCIE" rev 0x02: irq 3

pci3 at ppb2 bus 9

bge0 at pci3 dev 0 function 0 "Broadcom BCM5755M" rev 0x02, BCM5755 A2
(0xa002): irq 3, address 00:1e:c9:23:04:f0

brgphy0 at bge0 phy 1: BCM5755 10/100/1000baseT PHY, rev. 0

uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x02: irq 10

uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x02: irq 9

uhci4 at pci0 dev 29 function 2 "Intel 82801H USB" rev 0x02: irq 5

ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x02: irq 10

usb1 at ehci1: USB revision 2.0

uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1

ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xf2

pci4 at ppb3 bus 3

cbb0 at pci4 dev 1 function 0 vendor "O2 Micro", unknown product 0x7135
rev
0x21: irq 11

"O2 Micro Firewire" rev 0x02 at pci4 dev 1 function 4 not configured

cardslot0 at cbb0 slot 0 flags 0

cardbus0 at cardslot0: bus 4 device 0 cacheline 0x0, lattimer 0x20

pcmcia0 at cardslot0

ichpcib0 at pci0 dev 31 function 0 "Intel 82801HBM LPC" rev 0x02: PM
disabled

pciide0 at pci0 dev 31 function 1 "Intel 82801HBM IDE" rev 0x02: DMA,
channel
0 configured to compatibility, channel 1 configured to compatibility

atapiscsi0 at pciide0 channel 0 drive 0

scsibus0 at atapiscsi0: 2 targets, initiator 7

cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVD+-RW GSA-T21N, A1R1> ATAPI
5/cdrom
removable

cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2

pciide0: channel 1 ignored (disabled)

pciide1 at pci0 dev 31 function 2 "Intel 82801HBM SATA" rev 0x02: DMA,
channel
0 configured to native-PCI, channel 1 configured to native-PCI

pciide1: using irq 10 for native-PCI interrupt

wd0 at pciide1 channel 0 drive 0: <FUJITSU MHZ2080BH G2>

wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors

wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5

ichiic0 at pci0 dev 31 function 3 "Intel 82801H SMBus" rev 0x02: SMI

iic0 at ichiic0

spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM

spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM

usb2 at uhci0: USB revision 1.0

uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb3 at uhci1: USB revision 1.0

uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb4 at uhci2: USB revision 1.0

uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb5 at uhci3: USB revision 1.0

uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1

usb6 at uhci4: USB revision 1.0

uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1

isa0 at ichpcib0

isadma0 at isa0

com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo

pckbc0 at isa0 port 0x60/5

pckbd0 at pckbc0 (kbd slot)

pckbc0: using irq 1 for kbd slot

wskbd0 at pckbd0: console keyboard, using wsdisplay0

pms0 at pckbc0 (aux slot)

pckbc0: using irq 12 for aux slot

wsmouse0 at pms0 mux 0

pcppi0 at isa0 port 0x61

midi0 at pcppi0: <PC speaker>

spkr0 at pcppi0

npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16

biomask efe5 netmask efed ttymask ffff

mtrr: Pentium Pro MTRR support

umass0 at uhub1 port 1 configuration 1 interface 0 "Kingston
DataTraveler 2.0"
rev 2.00/2.00 addr 2

umass0: using SCSI over Bulk-Only

scsibus1 at umass0: 2 targets, initiator 0

sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2
0/direct removable

sd0: 3858MB, 491 cyl, 255 head, 63 sec, 512 bytes/sec, 7902208 sec total

softraid0 at root

root on sd0a swap on sd0b dump on sd0b



FreeBSD 7.14s dmesg:

aac0: <IBM ServeRAID-8k> port 0x4000-0x40ff mem
0xcce00000-0xccffffff,0xcafe0000-0xcaffffff irq 17 at device 0.0 on pci2

aac0: Enable Raw I/O

aac0: Enable 64-bit array

aac0: New comm. interface enabled

aac0: [ITHREAD]

aac0: ServeRAID 8k-l  , aac driver 2.0.0-1





;((((

Reply | Threaded
Open this post in threaded view
|

Re: Who runs OpenBSD with Adaptec ?

Eduardo Alvarenga
you have to use aac driver from 4.5+ for you controller to work.

http://www.openbsd.org/plus.html
(look for aac)


Regards,

2009/4/9 Ricardo Augusto de Souza <[hidden email]>

> I sent dmesg of my notebook. Sorry.
>
> OpenBSD 4.4 (rox) #0: Wed Apr  8 16:27:08 BRT 2009
>    root@Tux:/usr/sys/arch/i386/compile/rox
> cpu0: Intel(R) Xeon(R) CPU E5405 @ 2.00GHz ("GenuineIntel" 686-class) 2
> GHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
> CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,TM2
> ,CX16,xTPR
> real mem  = 2952105984 (2815MB)
> avail mem = 2856112128 (2723MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 01/29/09, BIOS32 rev. 0 @ 0xfd841,
> SMBIOS rev. 2.4 @ 0xaffcee80 (86 entries)
> bios0: vendor IBM version "-[GFE143AUS-1.13]-" date 01/29/2009
> bios0: IBM IBM System x3550 -[7978B1U]-
> acpi0 at bios0: rev 2
> acpi0: tables DSDT FACP APIC SRAT HPET MCFG ERST
> acpi0: wakeup devices PCI0(S5)
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpihpet0 at acpi0: 14318179 Hz
> acpiprt0 at acpi0: bus 19 (PCI6)
> acpiprt1 at acpi0: bus 23 (PCIA)
> acpiprt2 at acpi0: bus 1 (PCIS)
> acpiprt3 at acpi0: bus 0 (PCI0)
> acpicpu0 at acpi0
> bios0: ROM list: 0xc0000/0xb000 0xcb000/0x1800 0xcc800/0x1800
> 0xce000/0x5000!
> ipmi at mainbus0 not configured
> cpu0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel 5000X Host" rev 0x31
> ppb0 at pci0 dev 2 function 0 "Intel 5000 PCIE x8" rev 0x31
> pci1 at ppb0 bus 16
> ppb1 at pci1 dev 0 function 0 "Intel 6321ESB PCIE" rev 0x01
> pci2 at ppb1 bus 17
> ppb2 at pci2 dev 0 function 0 "Intel 6321ESB PCIE" rev 0x01
> pci3 at ppb2 bus 19
> ppb3 at pci3 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
> 0x04
> pci4 at ppb3 bus 20
> ppb4 at pci4 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
> 0x04
> pci5 at ppb4 bus 21
> em0 at pci5 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
> 3, address 00:15:17:7b:9a:b0
> em1 at pci5 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
> 10, address 00:15:17:7b:9a:b1
> ppb5 at pci4 dev 1 function 0 vendor "IDT", unknown product 0x8018 rev
> 0x04
> pci6 at ppb5 bus 22
> em2 at pci6 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
> 10, address 00:15:17:7b:9a:b2
> em3 at pci6 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06: irq
> 7, address 00:15:17:7b:9a:b3
> ppb6 at pci2 dev 1 function 0 "Intel 6321ESB PCIE" rev 0x01
> pci7 at ppb6 bus 18
> ppb7 at pci1 dev 0 function 3 "Intel 6321ESB PCIE-PCIX" rev 0x01
> pci8 at ppb7 bus 23
> ppb8 at pci0 dev 3 function 0 "Intel 5000 PCIE" rev 0x31
> pci9 at ppb8 bus 35
> ppb9 at pci0 dev 4 function 0 "Intel 5000 PCIE x8" rev 0x31
> pci10 at ppb9 bus 7
> ppb10 at pci10 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
> 0x04
> pci11 at ppb10 bus 8
> ppb11 at pci11 dev 0 function 0 vendor "IDT", unknown product 0x8018 rev
> 0x04
> pci12 at ppb11 bus 9
> em4 at pci12 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06:
> irq 7, address 00:15:17:7b:be:f0
> em5 at pci12 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06:
> irq 3, address 00:15:17:7b:be:f1
> ppb12 at pci11 dev 1 function 0 vendor "IDT", unknown product 0x8018 rev
> 0x04
> pci13 at ppb12 bus 10
> em6 at pci13 dev 0 function 0 "Intel PRO/1000 QP (82571EB)" rev 0x06:
> irq 3, address 00:15:17:7b:be:f2
> em7 at pci13 dev 0 function 1 "Intel PRO/1000 QP (82571EB)" rev 0x06:
> irq 10, address 00:15:17:7b:be:f3
> ppb13 at pci0 dev 5 function 0 "Intel 5000 PCIE" rev 0x31
> pci14 at ppb13 bus 34
> ppb14 at pci0 dev 6 function 0 "Intel 5000 PCIE" rev 0x31
> pci15 at ppb14 bus 3
> ppb15 at pci15 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xc3
> pci16 at ppb15 bus 4
> bnx0 at pci16 dev 0 function 0 "Broadcom BCM5708" rev 0x12: irq 7
> ppb16 at pci0 dev 7 function 0 "Intel 5000 PCIE" rev 0x31
> pci17 at ppb16 bus 2
> "Adaptec ASR-2120S" rev 0x02 at pci17 dev 0 function 0 not configured
> "Intel I/OAT" rev 0x31 at pci0 dev 8 function 0 not configured
> pchb1 at pci0 dev 16 function 0 "Intel 5000 Error Reporting" rev 0x31
> pchb2 at pci0 dev 16 function 1 "Intel 5000 Error Reporting" rev 0x31
> pchb3 at pci0 dev 16 function 2 "Intel 5000 Error Reporting" rev 0x31
> pchb4 at pci0 dev 17 function 0 "Intel 5000 Reserved" rev 0x31
> pchb5 at pci0 dev 19 function 0 "Intel 5000 Reserved" rev 0x31
> pchb6 at pci0 dev 21 function 0 "Intel 5000 FBD" rev 0x31
> pchb7 at pci0 dev 22 function 0 "Intel 5000 FBD" rev 0x31
> ppb17 at pci0 dev 28 function 0 "Intel 6321ESB PCIE" rev 0x09
> pci18 at ppb17 bus 5
> ppb18 at pci18 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xc3
> pci19 at ppb18 bus 6
> bnx1 at pci19 dev 0 function 0 "Broadcom BCM5708" rev 0x12: irq 3
> uhci0 at pci0 dev 29 function 0 "Intel 6321ESB USB" rev 0x09: irq 5
> uhci1 at pci0 dev 29 function 1 "Intel 6321ESB USB" rev 0x09: irq 11
> uhci2 at pci0 dev 29 function 2 "Intel 6321ESB USB" rev 0x09: irq 5
> ehci0 at pci0 dev 29 function 7 "Intel 6321ESB USB" rev 0x09: irq 5
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> ppb19 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xd9
> pci20 at ppb19 bus 1
> vga1 at pci20 dev 1 function 0 "ATI ES1000" rev 0x02
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> drm at vga1 unsupported
> ichpcib0 at pci0 dev 31 function 0 "Intel 6321ESB LPC" rev 0x09: PM
> disabled
> pciide0 at pci0 dev 31 function 1 "Intel 6321ESB IDE" rev 0x09: DMA,
> channel 0 configured to compatibility, channel 1 configured to
> compatibility
> atapiscsi0 at pciide0 channel 0 drive 0
> scsibus0 at atapiscsi0: 2 targets, initiator 7
> cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, RW/DVD GCC-T10N, 1.00> ATAPI
> 5/cdrom removable
> cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> pciide0: channel 1 ignored (disabled)
> ichiic0 at pci0 dev 31 function 3 "Intel 6321ESB SMBus" rev 0x09:
> polling
> iic0 at ichiic0
> usb1 at uhci0: USB revision 1.0
> uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb2 at uhci1: USB revision 1.0
> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci2: USB revision 1.0
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> isa0 at ichpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> biomask f965 netmask fded ttymask ffff
> mtrr: Pentium Pro MTRR support
> umass0 at uhub0 port 3 configuration 1 interface 0 "Kingston
> DataTraveler 2.0" rev 2.00/2.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus1 at umass0: 2 targets, initiator 0
> sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2
> 0/direct removable
> sd0: 3858MB, 491 cyl, 255 head, 63 sec, 512 bytes/sec, 7902208 sec total
> uhub4 at uhub2 port 2 "Silitek IBM USB HUB KEYBOARD" rev 1.10/1.00 addr
> 2
> uhidev0 at uhub4 port 1 configuration 1 interface 0 "Silitek IBM USB HUB
> KEYBOARD" rev 1.10/1.00 addr 3
> uhidev0: iclass 3/1
> ukbd0 at uhidev0: 8 modifier keys, 6 key codes
> wskbd1 at ukbd0 mux 1
> wskbd1: connecting to wsdisplay0
> uhidev1 at uhub4 port 3 configuration 1 interface 0 "vendor 0x15ca USB
> Optical Mouse" rev 2.00/5.12 addr 4
> uhidev1: iclass 3/1
> ums0 at uhidev1: 3 buttons, Z dir
> wsmouse0 at ums0 mux 0
> softraid0 at root
> root on sd0a swap on sd0b dump on sd0b
> bnx1: address 00:1a:64:79:f1:5a
> brgphy0 at bnx1 phy 1: BCM5708C 10/100/1000baseT PHY, rev. 6
> bnx0: address 00:1a:64:79:f1:58
> brgphy1 at bnx0 phy 1: BCM5708C 10/100/1000baseT PHY, rev. 6
>
> -----Mensagem original-----
> De: [hidden email] [mailto:[hidden email]] Em nome de
> Ricardo Augusto de Souza
> Enviada em: quinta-feira, 9 de abril de 2009 18:16
> Para: [hidden email]
> Assunto: Who runs OpenBSD with Adaptec ?
>
> Hi,
>
>
>
> I AM trying to install openBSD 4.4 on a IBM 3550 7978 B1U but OpenBSD
> didn4t
> recognize Adaptec ServeRaid 8k.
>
>
>
> I4d like to know if someone run it on a server with this raid
> controller.
>
>
>
> I installed a custom openbsd kernel ( with aac* support)  on  a USB
> stick ,
> boot it on IBM 3550 and this is the dmesg:
>
> I also tried disabling acpi.
>
>
>
> OpenBSD 4.4 (rox) #0: Wed Apr  8 16:27:08 BRT 2009
>
>    root@Tux:/usr/sys/arch/i386/compile/rox
>
> cpu0: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz ("GenuineIntel"
> 686-class) 2
> GHz
>
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
> CFLUS
> H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,
> CX16,
> xTPR
>
> real mem  = 2137350144 (2038MB)
>
> avail mem = 2058268672 (1962MB)
>
> mainbus0 at root
>
> bios0 at mainbus0: AT/286+ BIOS, date 07/25/08, BIOS32 rev. 0 @ 0xffa10,
> SMBIOS rev. 2.4 @ 0xf6be0 (62 entries)
>
> bios0: vendor Dell Inc. version "A07" date 07/25/2008
>
> bios0: Dell Inc. Latitude D530
>
> acpi0 at bios0: rev 2
>
> acpi0: tables DSDT FACP HPET APIC ASF! MCFG TCPA SLIC SSDT
>
> acpi0: wakeup devices PCI0(S5) PCIE(S4) USB1(S0) USB2(S0) USB3(S0)
> USB4(S0)
> USB5(S0) EHC2(S0) EHCI(S0) AZAL(S3) RP01(S3) RP02(S4) RP03(S3) RP04(S3)
> RP05(S3) RP06(S5) LID_(S3) PBTN(S4)
>
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
>
> acpihpet0 at acpi0: 14318179 Hz
>
> acpiprt0 at acpi0: bus 3 (PCIE)
>
> acpiprt1 at acpi0: bus -1 (AGP_)
>
> acpiprt2 at acpi0: bus 11 (RP01)
>
> acpiprt3 at acpi0: bus 12 (RP02)
>
> acpiprt4 at acpi0: bus -1 (RP03)
>
> acpiprt5 at acpi0: bus -1 (RP04)
>
> acpiprt6 at acpi0: bus -1 (RP05)
>
> acpiprt7 at acpi0: bus 9 (RP06)
>
> acpiprt8 at acpi0: bus 0 (PCI0)
>
> acpicpu0 at acpi0: C3
>
> acpitz0 at acpi0: critical temperature 99 degC
>
> acpibtn0 at acpi0: LID_
>
> acpibtn1 at acpi0: PBTN
>
> acpibtn2 at acpi0: SBTN
>
> acpiac0 at acpi0: AC unit offline
>
> acpibat0 at acpi0: BAT0 model "DELL TT7108" serial 4001 type LION oem
> "Sanyo"
>
> acpibat1 at acpi0: BAT1 not present
>
> acpidock at acpi0 not configured
>
> acpivideo at acpi0 not configured
>
> acpivideo at acpi0 not configured
>
> acpivideo at acpi0 not configured
>
> bios0: ROM list: 0xc0000/0xf000! 0xcf000/0x1000
>
> cpu0 at mainbus0
>
> cpu0: unknown Enhanced SpeedStep CPU, msr 0x06170b2d06000a25
>
> cpu0: using only highest, current and lowest power states
>
> cpu0: Enhanced SpeedStep 2000 MHz (1292 mV): speeds: 2200, 2000, 1200
> MHz
>
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
>
> pchb0 at pci0 dev 0 function 0 "Intel GM965 Host" rev 0x0c
>
> vga1 at pci0 dev 2 function 0 "Intel GM965 Video" rev 0x0c
>
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
>
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
>
> agp0 at vga1: aperture at 0xe0000000, size 0x10000000
>
> drm at vga1 unsupported
>
> "Intel GM965 Video" rev 0x0c at pci0 dev 2 function 1 not configured
>
> uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x02: irq 10
>
> uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x02: irq 9
>
> ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x02: irq 5
>
> usb0 at ehci0: USB revision 2.0
>
> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
>
> azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x02: irq
> 9
>
> azalia0: codec[s]: Sigmatel/0x76a0, Conexant/0x2c06, using
> Sigmatel/0x76a0
>
> audio0 at azalia0
>
> ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x02: irq 11
>
> pci1 at ppb0 bus 11
>
> ppb1 at pci0 dev 28 function 1 "Intel 82801H PCIE" rev 0x02: irq 3
>
> pci2 at ppb1 bus 12
>
> wpi0 at pci2 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02: irq
> 3,
> MoW2, address 00:1f:3c:bf:c0:9d
>
> ppb2 at pci0 dev 28 function 5 "Intel 82801H PCIE" rev 0x02: irq 3
>
> pci3 at ppb2 bus 9
>
> bge0 at pci3 dev 0 function 0 "Broadcom BCM5755M" rev 0x02, BCM5755 A2
> (0xa002): irq 3, address 00:1e:c9:23:04:f0
>
> brgphy0 at bge0 phy 1: BCM5755 10/100/1000baseT PHY, rev. 0
>
> uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x02: irq 10
>
> uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x02: irq 9
>
> uhci4 at pci0 dev 29 function 2 "Intel 82801H USB" rev 0x02: irq 5
>
> ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x02: irq 10
>
> usb1 at ehci1: USB revision 2.0
>
> uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
>
> ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xf2
>
> pci4 at ppb3 bus 3
>
> cbb0 at pci4 dev 1 function 0 vendor "O2 Micro", unknown product 0x7135
> rev
> 0x21: irq 11
>
> "O2 Micro Firewire" rev 0x02 at pci4 dev 1 function 4 not configured
>
> cardslot0 at cbb0 slot 0 flags 0
>
> cardbus0 at cardslot0: bus 4 device 0 cacheline 0x0, lattimer 0x20
>
> pcmcia0 at cardslot0
>
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801HBM LPC" rev 0x02: PM
> disabled
>
> pciide0 at pci0 dev 31 function 1 "Intel 82801HBM IDE" rev 0x02: DMA,
> channel
> 0 configured to compatibility, channel 1 configured to compatibility
>
> atapiscsi0 at pciide0 channel 0 drive 0
>
> scsibus0 at atapiscsi0: 2 targets, initiator 7
>
> cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVD+-RW GSA-T21N, A1R1> ATAPI
> 5/cdrom
> removable
>
> cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
>
> pciide0: channel 1 ignored (disabled)
>
> pciide1 at pci0 dev 31 function 2 "Intel 82801HBM SATA" rev 0x02: DMA,
> channel
> 0 configured to native-PCI, channel 1 configured to native-PCI
>
> pciide1: using irq 10 for native-PCI interrupt
>
> wd0 at pciide1 channel 0 drive 0: <FUJITSU MHZ2080BH G2>
>
> wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors
>
> wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
>
> ichiic0 at pci0 dev 31 function 3 "Intel 82801H SMBus" rev 0x02: SMI
>
> iic0 at ichiic0
>
> spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
>
> spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
>
> usb2 at uhci0: USB revision 1.0
>
> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>
> usb3 at uhci1: USB revision 1.0
>
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>
> usb4 at uhci2: USB revision 1.0
>
> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>
> usb5 at uhci3: USB revision 1.0
>
> uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>
> usb6 at uhci4: USB revision 1.0
>
> uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>
> isa0 at ichpcib0
>
> isadma0 at isa0
>
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
>
> pckbc0 at isa0 port 0x60/5
>
> pckbd0 at pckbc0 (kbd slot)
>
> pckbc0: using irq 1 for kbd slot
>
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
>
> pms0 at pckbc0 (aux slot)
>
> pckbc0: using irq 12 for aux slot
>
> wsmouse0 at pms0 mux 0
>
> pcppi0 at isa0 port 0x61
>
> midi0 at pcppi0: <PC speaker>
>
> spkr0 at pcppi0
>
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
>
> biomask efe5 netmask efed ttymask ffff
>
> mtrr: Pentium Pro MTRR support
>
> umass0 at uhub1 port 1 configuration 1 interface 0 "Kingston
> DataTraveler 2.0"
> rev 2.00/2.00 addr 2
>
> umass0: using SCSI over Bulk-Only
>
> scsibus1 at umass0: 2 targets, initiator 0
>
> sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2
> 0/direct removable
>
> sd0: 3858MB, 491 cyl, 255 head, 63 sec, 512 bytes/sec, 7902208 sec total
>
> softraid0 at root
>
> root on sd0a swap on sd0b dump on sd0b
>
>
>
> FreeBSD 7.14s dmesg:
>
> aac0: <IBM ServeRAID-8k> port 0x4000-0x40ff mem
> 0xcce00000-0xccffffff,0xcafe0000-0xcaffffff irq 17 at device 0.0 on pci2
>
> aac0: Enable Raw I/O
>
> aac0: Enable 64-bit array
>
> aac0: New comm. interface enabled
>
> aac0: [ITHREAD]
>
> aac0: ServeRAID 8k-l  , aac driver 2.0.0-1
>
>
>
>
>
> ;((((
>
>


--
Eduardo Alvarenga

Reply | Threaded
Open this post in threaded view
|

Re: Who runs OpenBSD with Adaptec ?

Alexander Yurchenko-3
In reply to this post by Ricardo Augusto de Souza
please stop sending zillion of mails and just listen carefully what do
people are trying to tell you.

to get openbsd working with your adaptec you need to get another i386
machine (like your laptop). you need to download and install the latest
snapshot from here: ftp://ftp.openbsd.org/pub/OpenBSD/snapshots/i386.
once you have a machine running -current you need to get the latest
sources from anoncvs, see www.openbsd.org/anoncvs.html for details. then
you need to enable aac driver in both GENERIC and RAMDISK_CD configs.
then read carefully man release and do exacly what it says.

if you do everything right i'll get an openbsd45.iso that you can try to
install.

now please go work.

--
Alexander Yurchenko