Tyan Thunder LE SMP issues

classic Classic list List threaded Threaded
7 messages Options
Reply | Threaded
Open this post in threaded view
|

Tyan Thunder LE SMP issues

Lokkju
Hey all, hoping someone might be able to point me in some sort of direction...

I recently was given two BOXX brand 1u servers, both of which are the
exact same - Tyan Thunder LE 2510 dual proc motherboards, with two
867Mhz chips per board, and 4 256MB ram sticks per board.  The rest
you can get from the dmesg.

Anyway, I have been trying to get OpenBSD to run on them, and I
continuously have problems on processor 1 - and no, it does not matter
WHICH processor is in slot 1.  I usually get an apm error, but
sometimes I get tcp related, or copyout related, or other errors - all
ending up with me dumped into ddb.  These are usually "stopped"
errors, not panics.  In this case, the error is a apm_cpu_idle stopped
error.

So, here it goes - the dmesg, the trace on each processor, and the ps
- as I side note, I can almost always instigate this crash by trying
to untar something big - especially is I use verbose mode.

PANIC
********
# Stopped at      apm_cpu_idle+0x4a:      leal    0xfffffff4(%ebp),%esp
ddb{0}> show panic
the kernel did not panic

DMESG
*********
OpenBSD 3.8 (GENERIC.MP) #298: Sat Sep 10 15:51:54 MDT 2005
    [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 864 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,S
ER,MMX,FXSR,SSE
real mem  = 1073324032 (1048168K)
avail mem = 972730368 (949932K)
using 4278 buffers containing 53768192 bytes (52508K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 10/31/00, BIOS32 rev. 0 @ 0xfdba0
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown, estimated 0:00 hours
apm0: APM get event: interface not connected (3)
apm0: APM get event: interface not connected (3)
apm0: disconnected
apm0: flags 30102 dobusy 0 doidle 0
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf5200/192 (10 entries)
pcibios0: PCI Interrupt Router at 000:15:0 ("ServerWorks ROSB4 SouthBridge" rev
 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1000
ainbus0: Intel MP Specification (Version 1.4) (AMI      CNB30LE     )
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 132 MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel Pentium III ("GenuineIntel" 686-class) 864 MHz
cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,S
ER,MMX,FXSR,SSE
mainbus0: bus 0 is type PCI
mainbus0: bus 1 is type PCI
mainbus0: bus 2 is type ISA
ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 11, 16 pins
ioapic1 at mainbus0: apid 5 pa 0xfec01000, version 11, 16 pins
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20LE Host" rev 0x06
pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20LE Host" rev 0x06
pci1 at pchb1 bus 1
vga1 at pci0 dev 1 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
fxp0 at pci0 dev 4 function 0 "Intel 82557" rev 0x08, i82559: apic 5 int 4 (irq
  11), address 00:e0:81:01:cb:ca
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
pcib0 at pci0 dev 15 function 0 "ServerWorks ROSB4 SouthBridge" rev 0x50
pciide0 at pci0 dev 15 function 1 "ServerWorks OSB4 IDE" rev 0x00: DMA
wd0 at pciide0 channel 0 drive 0: <Maxtor 6Y060L0>
wd0: 16-sector PIO, LBA, 58644MB, 120103200 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev 0x04: apic 4 in
t 10 (irq 10), version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: ServerWorks OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 0 netmask 0 ttymask 0
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
WARNING: / was not properly unmounted
Stopped at      apm_cpu_idle+0x4a:      leal    0xfffffff4(%ebp),%esp

PS
*******
db{0}> ps
   PID   PPID   PGRP    UID  S       FLAGS  WAIT       COMMAND
  12120  24238  24238      0  7   0x2004006             gzip
  24238  24978  24238      0  3   0x2004086  piperd     tar
  24978  14077  24978      0  3   0x2004086  pause      ksh
  14077    286  14077   1000  3   0x2004086  pause      ksh
   286  13427  13427   1000  3   0x2000184  select     sshd
  13427   2111  13427      0  3   0x2004084  netio      sshd
  1338      1   1338      0  3   0x2004086  ttyin      ksh
   252      1    252      0  3   0x2004086  ttyin      getty
  25463      1  25463      0  3   0x2004086  ttyin      getty
  16238      1  16238      0  3   0x2004086  ttyin      getty
  1816      1   1816      0  3   0x2004086  ttyin      getty
  10733      1  10733      0  3   0x2004086  ttyin      getty
  4308      1   4308      0  3   0x2000084  select     cron
  2111      1   2111      0  3   0x2000084  select     sshd
  28870      1  28870      0  3   0x2040184  select     sendmail
  29920      1  29920      0  3   0x2000184  select     inetd
  7572  19905  19905     83  3   0x2000184  poll       ntpd
  19905      1  19905      0  3   0x2000084  poll       ntpd
  18307   7623   7623     73  3   0x2000184  poll       syslogd
  7623      1   7623      0  3   0x2000084  netio      syslogd
    11      0      0      0  3   0x2100204  crypto_wa  crypto
   10      0      0      0  3   0x2100204  aiodoned   aiodoned
     9      0      0      0  3   0x2100204  syncer     update
     8      0      0      0  3   0x2100204  cleaner    cleaner
     7      0      0      0  3    0x100204  reaper     reaper
     6      0      0      0  3   0x2100204  pgdaemon   pagedaemon
     5      0      0      0  3   0x2100204  pftm       pfpurge
     4      0      0      0  3   0x2100204  usbtsk     usbtask
     3      0      0      0  3   0x2100204  usbevt     usb0
     2      0      0      0  3   0x2100204  kmalloc    kmthread
     1      0      1      0  3   0x2004084  wait       init
     0     -1      0      0  3   0x2080204  scheduler  swapper

TRACE PROC 0
*******************
ddb{0}> trace
apm_cpu_idle(0,0,0,0,0) at apm_cpu_idle+0x4a

TRACE PROC 1
*******************
When I try switching to proc 1, using machine ddb 1, it hangs...



Well, that's all folks - I hope someone can help me...

Thanks
Nick

Reply | Threaded
Open this post in threaded view
|

Re: Tyan Thunder LE SMP issues

Brian A. Seklecki
Why were they given to you? Something wrong with them perhaps.  Try
booting Memtest86+ ISO and let it ride for a while?

Try another kernel from another OS?  Try a non MP kernel?

~BAS

On Wed, 2005-11-16 at 22:01, Lokkju wrote:

> Hey all, hoping someone might be able to point me in some sort of direction...
>
> I recently was given two BOXX brand 1u servers, both of which are the
> exact same - Tyan Thunder LE 2510 dual proc motherboards, with two
> 867Mhz chips per board, and 4 256MB ram sticks per board.  The rest
> you can get from the dmesg.
>
> Anyway, I have been trying to get OpenBSD to run on them, and I
> continuously have problems on processor 1 - and no, it does not matter
> WHICH processor is in slot 1.  I usually get an apm error, but
> sometimes I get tcp related, or copyout related, or other errors - all
> ending up with me dumped into ddb.  These are usually "stopped"
> errors, not panics.  In this case, the error is a apm_cpu_idle stopped
> error.
>
> So, here it goes - the dmesg, the trace on each processor, and the ps
> - as I side note, I can almost always instigate this crash by trying
> to untar something big - especially is I use verbose mode.
>
> PANIC
> ********
> # Stopped at      apm_cpu_idle+0x4a:      leal    0xfffffff4(%ebp),%esp
> ddb{0}> show panic
> the kernel did not panic
>
> DMESG
> *********
> OpenBSD 3.8 (GENERIC.MP) #298: Sat Sep 10 15:51:54 MDT 2005
>     [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC.MP
> cpu0: Intel Pentium III ("GenuineIntel" 686-class) 864 MHz
> cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,S
> ER,MMX,FXSR,SSE
> real mem  = 1073324032 (1048168K)
> avail mem = 972730368 (949932K)
> using 4278 buffers containing 53768192 bytes (52508K) of memory
> mainbus0 (root)
> bios0 at mainbus0: AT/286+(00) BIOS, date 10/31/00, BIOS32 rev. 0 @ 0xfdba0
> apm0 at bios0: Power Management spec V1.2
> apm0: AC on, battery charge unknown, estimated 0:00 hours
> apm0: APM get event: interface not connected (3)
> apm0: APM get event: interface not connected (3)
> apm0: disconnected
> apm0: flags 30102 dobusy 0 doidle 0
> pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
> pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf5200/192 (10 entries)
> pcibios0: PCI Interrupt Router at 000:15:0 ("ServerWorks ROSB4 SouthBridge" rev
>  0x00)
> pcibios0: PCI bus #0 is the last bus
> bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1000
> ainbus0: Intel MP Specification (Version 1.4) (AMI      CNB30LE     )
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: apic clock running at 132 MHz
> cpu1 at mainbus0: apid 1 (application processor)
> cpu1: Intel Pentium III ("GenuineIntel" 686-class) 864 MHz
> cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,S
> ER,MMX,FXSR,SSE
> mainbus0: bus 0 is type PCI
> mainbus0: bus 1 is type PCI
> mainbus0: bus 2 is type ISA
> ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 11, 16 pins
> ioapic1 at mainbus0: apid 5 pa 0xfec01000, version 11, 16 pins
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20LE Host" rev 0x06
> pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20LE Host" rev 0x06
> pci1 at pchb1 bus 1
> vga1 at pci0 dev 1 function 0 "ATI Rage XL" rev 0x27
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> fxp0 at pci0 dev 4 function 0 "Intel 82557" rev 0x08, i82559: apic 5 int 4 (irq
>   11), address 00:e0:81:01:cb:ca
> inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
> pcib0 at pci0 dev 15 function 0 "ServerWorks ROSB4 SouthBridge" rev 0x50
> pciide0 at pci0 dev 15 function 1 "ServerWorks OSB4 IDE" rev 0x00: DMA
> wd0 at pciide0 channel 0 drive 0: <Maxtor 6Y060L0>
> wd0: 16-sector PIO, LBA, 58644MB, 120103200 sectors
> wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
> ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev 0x04: apic 4 in
> t 10 (irq 10), version 1.0, legacy support
> usb0 at ohci0: USB revision 1.0
> uhub0 at usb0
> uhub0: ServerWorks OHCI root hub, rev 1.00/1.00, addr 1
> uhub0: 4 ports with 4 removable, self powered
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pmsi0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pmsi0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> sysbeep0 at pcppi0
> npx0 at isa0 port 0xf0/16: using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pccom0: console
> pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> biomask 0 netmask 0 ttymask 0
> pctr: 686-class user-level performance counters enabled
> mtrr: Pentium Pro MTRR support
> dkcsum: wd0 matches BIOS drive 0x80
> root on wd0a
> rootdev=0x0 rrootdev=0x300 rawdev=0x302
> WARNING: / was not properly unmounted
> Stopped at      apm_cpu_idle+0x4a:      leal    0xfffffff4(%ebp),%esp
>
> PS
> *******
> db{0}> ps
>    PID   PPID   PGRP    UID  S       FLAGS  WAIT       COMMAND
>   12120  24238  24238      0  7   0x2004006             gzip
>   24238  24978  24238      0  3   0x2004086  piperd     tar
>   24978  14077  24978      0  3   0x2004086  pause      ksh
>   14077    286  14077   1000  3   0x2004086  pause      ksh
>    286  13427  13427   1000  3   0x2000184  select     sshd
>   13427   2111  13427      0  3   0x2004084  netio      sshd
>   1338      1   1338      0  3   0x2004086  ttyin      ksh
>    252      1    252      0  3   0x2004086  ttyin      getty
>   25463      1  25463      0  3   0x2004086  ttyin      getty
>   16238      1  16238      0  3   0x2004086  ttyin      getty
>   1816      1   1816      0  3   0x2004086  ttyin      getty
>   10733      1  10733      0  3   0x2004086  ttyin      getty
>   4308      1   4308      0  3   0x2000084  select     cron
>   2111      1   2111      0  3   0x2000084  select     sshd
>   28870      1  28870      0  3   0x2040184  select     sendmail
>   29920      1  29920      0  3   0x2000184  select     inetd
>   7572  19905  19905     83  3   0x2000184  poll       ntpd
>   19905      1  19905      0  3   0x2000084  poll       ntpd
>   18307   7623   7623     73  3   0x2000184  poll       syslogd
>   7623      1   7623      0  3   0x2000084  netio      syslogd
>     11      0      0      0  3   0x2100204  crypto_wa  crypto
>    10      0      0      0  3   0x2100204  aiodoned   aiodoned
>      9      0      0      0  3   0x2100204  syncer     update
>      8      0      0      0  3   0x2100204  cleaner    cleaner
>      7      0      0      0  3    0x100204  reaper     reaper
>      6      0      0      0  3   0x2100204  pgdaemon   pagedaemon
>      5      0      0      0  3   0x2100204  pftm       pfpurge
>      4      0      0      0  3   0x2100204  usbtsk     usbtask
>      3      0      0      0  3   0x2100204  usbevt     usb0
>      2      0      0      0  3   0x2100204  kmalloc    kmthread
>      1      0      1      0  3   0x2004084  wait       init
>      0     -1      0      0  3   0x2080204  scheduler  swapper
>
> TRACE PROC 0
> *******************
> ddb{0}> trace
> apm_cpu_idle(0,0,0,0,0) at apm_cpu_idle+0x4a
>
> TRACE PROC 1
> *******************
> When I try switching to proc 1, using machine ddb 1, it hangs...
>
>
>
> Well, that's all folks - I hope someone can help me...
>
> Thanks
> Nick

Reply | Threaded
Open this post in threaded view
|

Re: Tyan Thunder LE SMP issues

Lokkju
Sorry, given in this context means someone is letting me play with
them to see if I can get them working with OpenBSD.  They display
equivalent crashes in NetBSD - I have not tried FreeBSD or any linux
distros.  As for Memcheck86+, I can leave it running for over 24 hours
with no issues, and no errors reported.


On 11/16/05, Brian A. Seklecki <[hidden email]> wrote:

> Why were they given to you? Something wrong with them perhaps.  Try
> booting Memtest86+ ISO and let it ride for a while?
>
> Try another kernel from another OS?  Try a non MP kernel?
>
> ~BAS
>
> On Wed, 2005-11-16 at 22:01, Lokkju wrote:
> > Hey all, hoping someone might be able to point me in some sort of direction...
> >
> > I recently was given two BOXX brand 1u servers, both of which are the
> > exact same - Tyan Thunder LE 2510 dual proc motherboards, with two
> > 867Mhz chips per board, and 4 256MB ram sticks per board.  The rest
> > you can get from the dmesg.
> >
> > Anyway, I have been trying to get OpenBSD to run on them, and I
> > continuously have problems on processor 1 - and no, it does not matter
> > WHICH processor is in slot 1.  I usually get an apm error, but
> > sometimes I get tcp related, or copyout related, or other errors - all
> > ending up with me dumped into ddb.  These are usually "stopped"
> > errors, not panics.  In this case, the error is a apm_cpu_idle stopped
> > error.
> >
> > So, here it goes - the dmesg, the trace on each processor, and the ps
> > - as I side note, I can almost always instigate this crash by trying
> > to untar something big - especially is I use verbose mode.
> >
> > PANIC
> > ********
> > # Stopped at      apm_cpu_idle+0x4a:      leal    0xfffffff4(%ebp),%esp
> > ddb{0}> show panic
> > the kernel did not panic
> >
> > DMESG
> > *********
> > OpenBSD 3.8 (GENERIC.MP) #298: Sat Sep 10 15:51:54 MDT 2005
> >     [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC.MP
> > cpu0: Intel Pentium III ("GenuineIntel" 686-class) 864 MHz
> > cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,S
> > ER,MMX,FXSR,SSE
> > real mem  = 1073324032 (1048168K)
> > avail mem = 972730368 (949932K)
> > using 4278 buffers containing 53768192 bytes (52508K) of memory
> > mainbus0 (root)
> > bios0 at mainbus0: AT/286+(00) BIOS, date 10/31/00, BIOS32 rev. 0 @ 0xfdba0
> > apm0 at bios0: Power Management spec V1.2
> > apm0: AC on, battery charge unknown, estimated 0:00 hours
> > apm0: APM get event: interface not connected (3)
> > apm0: APM get event: interface not connected (3)
> > apm0: disconnected
> > apm0: flags 30102 dobusy 0 doidle 0
> > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
> > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf5200/192 (10 entries)
> > pcibios0: PCI Interrupt Router at 000:15:0 ("ServerWorks ROSB4 SouthBridge" rev
> >  0x00)
> > pcibios0: PCI bus #0 is the last bus
> > bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1000
> > ainbus0: Intel MP Specification (Version 1.4) (AMI      CNB30LE     )
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: apic clock running at 132 MHz
> > cpu1 at mainbus0: apid 1 (application processor)
> > cpu1: Intel Pentium III ("GenuineIntel" 686-class) 864 MHz
> > cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,S
> > ER,MMX,FXSR,SSE
> > mainbus0: bus 0 is type PCI
> > mainbus0: bus 1 is type PCI
> > mainbus0: bus 2 is type ISA
> > ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 11, 16 pins
> > ioapic1 at mainbus0: apid 5 pa 0xfec01000, version 11, 16 pins
> > pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> > pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20LE Host" rev 0x06
> > pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20LE Host" rev 0x06
> > pci1 at pchb1 bus 1
> > vga1 at pci0 dev 1 function 0 "ATI Rage XL" rev 0x27
> > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> > wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> > fxp0 at pci0 dev 4 function 0 "Intel 82557" rev 0x08, i82559: apic 5 int 4 (irq
> >   11), address 00:e0:81:01:cb:ca
> > inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
> > pcib0 at pci0 dev 15 function 0 "ServerWorks ROSB4 SouthBridge" rev 0x50
> > pciide0 at pci0 dev 15 function 1 "ServerWorks OSB4 IDE" rev 0x00: DMA
> > wd0 at pciide0 channel 0 drive 0: <Maxtor 6Y060L0>
> > wd0: 16-sector PIO, LBA, 58644MB, 120103200 sectors
> > wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
> > ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev 0x04: apic 4 in
> > t 10 (irq 10), version 1.0, legacy support
> > usb0 at ohci0: USB revision 1.0
> > uhub0 at usb0
> > uhub0: ServerWorks OHCI root hub, rev 1.00/1.00, addr 1
> > uhub0: 4 ports with 4 removable, self powered
> > isa0 at pcib0
> > isadma0 at isa0
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pmsi0 at pckbc0 (aux slot)
> > pckbc0: using irq 12 for aux slot
> > wsmouse0 at pmsi0 mux 0
> > pcppi0 at isa0 port 0x61
> > midi0 at pcppi0: <PC speaker>
> > spkr0 at pcppi0
> > sysbeep0 at pcppi0
> > npx0 at isa0 port 0xf0/16: using exception 16
> > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pccom0: console
> > pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> > fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> > biomask 0 netmask 0 ttymask 0
> > pctr: 686-class user-level performance counters enabled
> > mtrr: Pentium Pro MTRR support
> > dkcsum: wd0 matches BIOS drive 0x80
> > root on wd0a
> > rootdev=0x0 rrootdev=0x300 rawdev=0x302
> > WARNING: / was not properly unmounted
> > Stopped at      apm_cpu_idle+0x4a:      leal    0xfffffff4(%ebp),%esp
> >
> > PS
> > *******
> > db{0}> ps
> >    PID   PPID   PGRP    UID  S       FLAGS  WAIT       COMMAND
> >   12120  24238  24238      0  7   0x2004006             gzip
> >   24238  24978  24238      0  3   0x2004086  piperd     tar
> >   24978  14077  24978      0  3   0x2004086  pause      ksh
> >   14077    286  14077   1000  3   0x2004086  pause      ksh
> >    286  13427  13427   1000  3   0x2000184  select     sshd
> >   13427   2111  13427      0  3   0x2004084  netio      sshd
> >   1338      1   1338      0  3   0x2004086  ttyin      ksh
> >    252      1    252      0  3   0x2004086  ttyin      getty
> >   25463      1  25463      0  3   0x2004086  ttyin      getty
> >   16238      1  16238      0  3   0x2004086  ttyin      getty
> >   1816      1   1816      0  3   0x2004086  ttyin      getty
> >   10733      1  10733      0  3   0x2004086  ttyin      getty
> >   4308      1   4308      0  3   0x2000084  select     cron
> >   2111      1   2111      0  3   0x2000084  select     sshd
> >   28870      1  28870      0  3   0x2040184  select     sendmail
> >   29920      1  29920      0  3   0x2000184  select     inetd
> >   7572  19905  19905     83  3   0x2000184  poll       ntpd
> >   19905      1  19905      0  3   0x2000084  poll       ntpd
> >   18307   7623   7623     73  3   0x2000184  poll       syslogd
> >   7623      1   7623      0  3   0x2000084  netio      syslogd
> >     11      0      0      0  3   0x2100204  crypto_wa  crypto
> >    10      0      0      0  3   0x2100204  aiodoned   aiodoned
> >      9      0      0      0  3   0x2100204  syncer     update
> >      8      0      0      0  3   0x2100204  cleaner    cleaner
> >      7      0      0      0  3    0x100204  reaper     reaper
> >      6      0      0      0  3   0x2100204  pgdaemon   pagedaemon
> >      5      0      0      0  3   0x2100204  pftm       pfpurge
> >      4      0      0      0  3   0x2100204  usbtsk     usbtask
> >      3      0      0      0  3   0x2100204  usbevt     usb0
> >      2      0      0      0  3   0x2100204  kmalloc    kmthread
> >      1      0      1      0  3   0x2004084  wait       init
> >      0     -1      0      0  3   0x2080204  scheduler  swapper
> >
> > TRACE PROC 0
> > *******************
> > ddb{0}> trace
> > apm_cpu_idle(0,0,0,0,0) at apm_cpu_idle+0x4a
> >
> > TRACE PROC 1
> > *******************
> > When I try switching to proc 1, using machine ddb 1, it hangs...
> >
> >
> >
> > Well, that's all folks - I hope someone can help me...
> >
> > Thanks
> > Nick

Reply | Threaded
Open this post in threaded view
|

Re: Tyan Thunder LE SMP issues

Tobias Weingartner-2
On Wednesday, November 16, Lokkju wrote:
>
> Sorry, given in this context means someone is letting me play with
> them to see if I can get them working with OpenBSD.  They display
> equivalent crashes in NetBSD - I have not tried FreeBSD or any linux
> distros.

Ok, if 2 operating systems show similar crashes...  I'd hazard a safe
guess that there is something broken.

> As for Memcheck86+, I can leave it running for over 24 hours
> with no issues, and no errors reported.

As far as I know, this is UP, and does not use SMP.  Chances are you
have some sort of SMP issue... maybe with the 2nd CPU.

--Toby.

Reply | Threaded
Open this post in threaded view
|

Re: Tyan Thunder LE SMP issues

Brian A. Seklecki
> As far as I know, this is UP, and does not use SMP.  Chances are you
> have some sort of SMP issue... maybe with the 2nd CPU.

He indicated that he swapped them up.

>
> --Toby.
>

l8*
  -lava

x.25 - minix - bitnet - plan9 - 110 bps - ASR 33 - base8

Reply | Threaded
Open this post in threaded view
|

Re: Tyan Thunder LE SMP issues

Lokkju
Well, according to Theo, this is something of a known bug - he told me
that you (Toby) were working on it...

As Brain said, I have swapped the processors, and run memcheck86 with
each of them being in the first slot.  If anyone has any further
suggestions on how I might test the hardware portion, I would love to
try them, as I have a total of two duplicate motherboards, 4 duplicate
processors, and 8 duplicate 256MB ram sticks I can try swapping
around.

On 11/17/05, Brian A. Seklecki <[hidden email]> wrote:

> > As far as I know, this is UP, and does not use SMP.  Chances are you
> > have some sort of SMP issue... maybe with the 2nd CPU.
>
> He indicated that he swapped them up.
>
> >
> > --Toby.
> >
>
> l8*
>         -lava
>
> x.25 - minix - bitnet - plan9 - 110 bps - ASR 33 - base8

Reply | Threaded
Open this post in threaded view
|

Re: Tyan Thunder LE SMP issues

Tobias Weingartner-2
On Thursday, November 17, Lokkju wrote:
>
> Well, according to Theo, this is something of a known bug - he told me
> that you (Toby) were working on it...

I have yet to be convinced of that.  All the bugs in this area have so
far been hardware issues.  But I've been wrong before...

> As Brain said, I have swapped the processors, and run memcheck86 with
> each of them being in the first slot.  If anyone has any further
> suggestions on how I might test the hardware portion, I would love to
> try them, as I have a total of two duplicate motherboards, 4 duplicate
> processors, and 8 duplicate 256MB ram sticks I can try swapping
> around.

Split it into 2 "identical" systems.  See if both of them have the same
problem.  That would help me out somewhat.


--Toby.