[ROCKP64] emmc Install

classic Classic list List threaded Threaded
4 messages Options
Reply | Threaded
Open this post in threaded view
|

[ROCKP64] emmc Install

Olivier BURELLI
Hello,

I tried to install current on RockPro64 to eMMC.

_ I used the firmware provided by Marc (on microSD): https://marc.info/?l=openbsd-arm&m=156114869709200&w=2
_ I used an usb stick for miniroot

Once arrived to choose the whole disk... Impossible to write the eMMC disk. I tried to force via reinit... without success.

_ A reason ? (i will try (to validate the installation process) to install OpenBSD on the sd card.

Thanks in advance.


********************
* Installation log *
********************
cu -s 115200 -l /dev/cuaU0    
Connected to /dev/cuaU0 (speed 115200)

U-Boot TPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31)
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
Trying to boot from MMC1
NOTICE:  BL31: v2.1(debug):2.1
NOTICE:  BL31: Built : 21:16:08, Jul  4 2019
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    plat_rockchip_pmu_init(1596): pd status 3e
INFO:    BL31: Initializing runtime services
WARNING: BL31: cortex_a53: CPU workaround for 819472 was missing!
WARNING: BL31: cortex_a53: CPU workaround for 824069 was missing!
WARNING: BL31: cortex_a53: CPU workaround for 827319 was missing!
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)

Model: Pine64 RockPro64
DRAM:  3.9 GiB
MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial@ff1a0000
Out:   serial@ff1a0000
Err:   serial@ff1a0000
Model: Pine64 RockPro64
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Net:  
Error: ethernet@fe300000 address not set.
eth-1: ethernet@fe300000
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0(part 0) is current device
** No partition table - mmc 0 **
switch to partitions #0, OK
mmc1 is current device
** Invalid partition 1 **
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 2 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: Lexar    Rev: 1100 Prod: USB Flash Drive
            Type: Removable Hard Disk
            Capacity: 7634.0 MB = 7.4 GB (15634432 x 512)
... is now current device
Scanning usb 0:1...
Found EFI removable media binary efi/boot/bootaa64.efi
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk [hidden email]...
Scanning disk [hidden email]...
Scanning disk usb_mass_storage.lun0...
Found 5 disks
BootOrder not defined
EFI boot manager: Cannot load any image
165119 bytes read in 56 ms (2.8 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
disks: sd0* sd1 sd2
>> OpenBSD/arm64 BOOTAA64 0.20
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2228484+623928+8770112+752864 [180632+109+521472+201593]=0xff1d68
Host not halted after 16000 microseconds.
type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8
type 0x7 pa 0x4200000 va 0x4200000 pages 0x3eec attr 0x8
type 0x4 pa 0x80ec000 va 0x80ec000 pages 0x28 attr 0x8
type 0x7 pa 0x8114000 va 0x8114000 pages 0xec0a6 attr 0x8
type 0x2 pa 0xf41ba000 va 0xf41ba000 pages 0xc33 attr 0x8
type 0x7 pa 0xf4ded000 va 0xf4ded000 pages 0x1 attr 0x8
type 0x2 pa 0xf4dee000 va 0xf4dee000 pages 0x100 attr 0x8
type 0x1 pa 0xf4eee000 va 0xf4eee000 pages 0x29 attr 0x8
type 0x0 pa 0xf4f17000 va 0xf4f17000 pages 0x7 attr 0x8
type 0x4 pa 0xf4f1e000 va 0xf4f1e000 pages 0x1 attr 0x8
type 0x0 pa 0xf4f1f000 va 0xf4f1f000 pages 0x2 attr 0x8
type 0x6 pa 0xf4f21000 va 0xa3863000 pages 0x1 attr 0x8000000000000008
type 0x0 pa 0xf4f22000 va 0xf4f22000 pages 0x3 attr 0x8
type 0x4 pa 0xf4f25000 va 0xf4f25000 pages 0x2 attr 0x8
type 0x6 pa 0xf4f27000 va 0xa3869000 pages 0x1 attr 0x8000000000000008
type 0x2 pa 0xf4f28000 va 0xf4f28000 pages 0x3018 attr 0x8
type 0x5 pa 0xf7f40000 va 0xa6882000 pages 0x10 attr 0x8000000000000008
type 0x2 pa 0xf7f50000 va 0xf7f50000 pages 0xb0 attr 0x8
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2019 OpenBSD. All rights reserved.  https://www.OpenBSD.org

OpenBSD 6.6-current (RAMDISK) #333: Thu Nov 28 01:12:25 MST 2019
    [hidden email]:/usr/src/sys/arch/arm64/compile/RAMDISK
real mem  = 4093190144 (3903MB)
avail mem = 3891441664 (3711MB)
mainbus0 at root: Pine64 RockPro64
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu0: 512KB 64b/line 16-way L2 cache
efi0 at mainbus0: UEFI 2.8
efi0: Das U-Boot rev 0x20191000
psci0 at mainbus0: PSCI 1.1, SMCCC 1.1
agintc0 at mainbus0 sec shift 3:3 nirq 288 nredist 6: "interrupt-controller"
agintcmsi0 at agintc0
syscon0 at mainbus0: "qos"
syscon1 at mainbus0: "qos"
syscon2 at mainbus0: "qos"
syscon3 at mainbus0: "qos"
syscon4 at mainbus0: "qos"
syscon5 at mainbus0: "qos"
syscon6 at mainbus0: "qos"
syscon7 at mainbus0: "qos"
syscon8 at mainbus0: "qos"
syscon9 at mainbus0: "qos"
syscon10 at mainbus0: "qos"
syscon11 at mainbus0: "qos"
syscon12 at mainbus0: "qos"
syscon13 at mainbus0: "qos"
syscon14 at mainbus0: "qos"
syscon15 at mainbus0: "qos"
syscon16 at mainbus0: "qos"
syscon17 at mainbus0: "qos"
syscon18 at mainbus0: "qos"
syscon19 at mainbus0: "qos"
syscon20 at mainbus0: "qos"
syscon21 at mainbus0: "qos"
syscon22 at mainbus0: "qos"
syscon23 at mainbus0: "qos"
syscon24 at mainbus0: "qos"
syscon25 at mainbus0: "power-management"
"power-controller" at syscon25 not configured
syscon26 at mainbus0: "syscon"
"io-domains" at syscon26 not configured
syscon27 at mainbus0: "syscon"
syscon28 at mainbus0: "syscon"
rkclock0 at mainbus0
rkclock1 at mainbus0
syscon29 at mainbus0: "syscon"
"io-domains" at syscon29 not configured
"usb2-phy" at syscon29 not configured
"usb2-phy" at syscon29 not configured
"phy" at syscon29 not configured
rkpinctrl0 at mainbus0: "pinctrl"
rkgpio0 at rkpinctrl0
rkgpio1 at rkpinctrl0
rkgpio2 at rkpinctrl0
rkgpio3 at rkpinctrl0
rkgpio4 at rkpinctrl0
"fit-images" at mainbus0 not configured
"pmu_a53" at mainbus0 not configured
"pmu_a72" at mainbus0 not configured
agtimer0 at mainbus0: tick rate 24000 KHz
"xin24m" at mainbus0 not configured
simplebus0 at mainbus0: "amba"
"dma-controller" at simplebus0 not configured
"dma-controller" at simplebus0 not configured
dwge0 at mainbus0: address ff:ff:ff:ff:ff:ff
rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6
dwmmc0 at mainbus0: 50 MHz base clock
sdmmc0 at dwmmc0: 4-bit, sd high-speed, mmc high-speed, dma
sdhc0 at mainbus0
sdhc0: SDHC 3.0, 200 MHz base clock
sdmmc1 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
ehci0 at mainbus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
ohci0 at mainbus0: version 1.0
ehci1 at mainbus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
ohci1 at mainbus0: version 1.0
rkdwusb0 at mainbus0: "usb"
xhci0 at rkdwusb0, xHCI 1.10
usb2 at xhci0: USB revision 3.0
uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
rkdwusb1 at mainbus0: "usb"
xhci1 at rkdwusb1, xHCI 1.10
usb3 at xhci1: USB revision 3.0
uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
"saradc" at mainbus0 not configured
rkiic0 at mainbus0
iic0 at rkiic0
rkiic1 at mainbus0
iic1 at rkiic1
com0 at mainbus0: ns16550, no working fifo
com1 at mainbus0: ns16550, no working fifo
com1: console
"thermal-zones" at mainbus0 not configured
"tsadc" at mainbus0 not configured
rkiic2 at mainbus0
iic2 at rkiic2
rkpmic0 at iic2 addr 0x1b: RK808
"silergy,syr827" at iic2 addr 0x40 not configured
"silergy,syr828" at iic2 addr 0x41 not configured
rkiic3 at mainbus0
iic3 at rkiic3
fusbtc0 at iic3 addr 0x22
"pwm" at mainbus0 not configured
"pwm" at mainbus0 not configured
"dmc" at mainbus0 not configured
"efuse" at mainbus0 not configured
"phy" at mainbus0 not configured
"phy" at mainbus0 not configured
"watchdog" at mainbus0 not configured
"rktimer" at mainbus0 not configured
"i2s" at mainbus0 not configured
"i2s" at mainbus0 not configured
"i2s" at mainbus0 not configured
"vop" at mainbus0 not configured
"iommu" at mainbus0 not configured
"vop" at mainbus0 not configured
"iommu" at mainbus0 not configured
"hdmi" at mainbus0 not configured
"gpu" at mainbus0 not configured
"opp-table0" at mainbus0 not configured
"opp-table1" at mainbus0 not configured
"opp-table2" at mainbus0 not configured
"external-gmac-clock" at mainbus0 not configured
"gpio-keys" at mainbus0 not configured
"leds" at mainbus0 not configured
"sdio-pwrseq" at mainbus0 not configured
"vcc12v-dcin" at mainbus0 not configured
"vcc1v8-s3" at mainbus0 not configured
"vcc3v3-pcie-regulator" at mainbus0 not configured
"vcc3v3-sys" at mainbus0 not configured
"vcc5v0-host-regulator" at mainbus0 not configured
"vcc5v0-typec-regulator" at mainbus0 not configured
"vcc5v0-sys" at mainbus0 not configured
"vcc5v0-usb" at mainbus0 not configured
"vdd-log" at mainbus0 not configured
usb4 at ohci0: USB revision 1.0
uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci1: USB revision 1.0
uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SC16G, 0080> removable
sd0: 15193MB, 512 bytes/sector, 31116288 sectors
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4064, 0000> removable
sd1: 59640MB, 512 bytes/sector, 122142720 sectors
umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive" rev 2.10/11.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd2 at scsibus2 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable serial.05dca838E89K3FOCINZ7
sd2: 7634MB, 512 bytes/sector, 15634432 sectors
softraid0 at root
scsibus3 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: preposterous clock chip time
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T

Welcome to the OpenBSD/arm64 6.6 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN.  You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.

Terminal type? [vt220]
System hostname? (short form, e.g. 'foo') pinu

Available network interfaces are: dwge0 vlan0.
Which network interface do you wish to configure? (or 'done') [dwge0]
IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp]
dwge0: no link....
dwge0: xxx.xxx.xxx.12 lease accepted from xxx.xxx.xxx.254 (14:0c:xxx:xx:xx:xx)
IPv6 address for dwge0? (or 'autoconf' or 'none') [none] autoconf
Available network interfaces are: dwge0 vlan0.
Which network interface do you wish to configure? (or 'done') [done]
DNS domain name? (e.g. 'example.com') [my.domain] burelli.home
Using DNS nameservers at xxx.xxx.xxx.254 8.8.8.8

Password for root account? (will not echo)
Password for root account? (again)
Start sshd(8) by default? [yes]
Setup a user? (enter a lower-case loginname, or 'no') [no] olivier
Full name for user olivier? [oliv] Olivier Burelli
Password for user olivier? (will not echo)
Password for user olivier? (again)
WARNING: root is targeted by password guessing attacks, pubkeys are safer.
Allow root ssh login? (yes, no, prohibit-password) [no]
What timezone are you in? ('?' for list) [Europe/Paris]

Available disks are: sd0 sd1 sd2.
Which disk is the root disk? ('?' for details) [sd0] ?
sd0: SD/MMC, SC16G, 0080  (14.8G)
sd1: Sandisk, DA4064, 0000  (58.2G)
sd2: Lexar, USB Flash Drive, 1100 serial.05dca838E89K3FOCINZ7 (7.5G)
Available disks are: sd0 sd1 sd2.
Which disk is the root disk? ('?' for details) [sd0] sd1
Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
Offset: 0 Signature: 0xAA55
            Starting         Ending         LBA Info:
 #: id      C   H   S -      C   H   S [       start:        size ]
-------------------------------------------------------------------------------
 0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT  
Use (W)hole disk or (E)dit the MBR? [whole] e

You will now create one MBR partition to contain your OpenBSD data
and one MBR partition on which the OpenBSD boot program is located.
Neither partition will overlap any other partition.

The OpenBSD MBR partition will have an id of 'A6' and the boot MBR
partition will have an id of 'C' (msdos).
The boot partition will be at least 16MB and be the first 'MSDOS'
partition on the disk.

Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
Offset: 0 Signature: 0xAA55
            Starting         Ending         LBA Info:
 #: id      C   H   S -      C   H   S [       start:        size ]
-------------------------------------------------------------------------------
 0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT  
Enter 'help' for information
sd1: 1> reinit
Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
Offset: 0 Signature: 0xAA55
            Starting         Ending         LBA Info:
 #: id      C   H   S -      C   H   S [       start:        size ]
-------------------------------------------------------------------------------
 0: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
 1: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
 2: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
*3: A6      0   1   2 -   7602 254  63 [          64:   122142131 ] OpenBSD    
Use 'write' to update disk.
sd1*: 1> write
Writing MBR at offset 0.
sd1: 1> q
No OpenBSD partition in MBR, try again.
Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
Offset: 0 Signature: 0xAA55
            Starting         Ending         LBA Info:
 #: id      C   H   S -      C   H   S [       start:        size ]
-------------------------------------------------------------------------------
 0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
 3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT  
Use (W)hole disk or (E)dit the MBR? [whole]




--
burelli.fr <[hidden email]>

Reply | Threaded
Open this post in threaded view
|

Re: [ROCKP64] emmc Install

Olivier BURELLI
Hi arm,

Install was successful on the micro sd card.

Maybe i have to check the integrity of the eMMC card, in first.

Oliv.


On Thu, 28 Nov 2019 23:29:11 +0100
"burelli.fr" <[hidden email]> wrote:

> Hello,
>
> I tried to install current on RockPro64 to eMMC.
>
> _ I used the firmware provided by Marc (on microSD): https://marc.info/?l=openbsd-arm&m=156114869709200&w=2
> _ I used an usb stick for miniroot
>
> Once arrived to choose the whole disk... Impossible to write the eMMC disk. I tried to force via reinit... without success.
>
> _ A reason ? (i will try (to validate the installation process) to install OpenBSD on the sd card.
>
> Thanks in advance.
>
>
> ********************
> * Installation log *
> ********************
> cu -s 115200 -l /dev/cuaU0    
> Connected to /dev/cuaU0 (speed 115200)
>
> U-Boot TPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31)
> Trying to boot from BOOTROM
> Returning to boot ROM...
>
> U-Boot SPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
> Trying to boot from MMC1
> NOTICE:  BL31: v2.1(debug):2.1
> NOTICE:  BL31: Built : 21:16:08, Jul  4 2019
> INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
> INFO:    plat_rockchip_pmu_init(1596): pd status 3e
> INFO:    BL31: Initializing runtime services
> WARNING: BL31: cortex_a53: CPU workaround for 819472 was missing!
> WARNING: BL31: cortex_a53: CPU workaround for 824069 was missing!
> WARNING: BL31: cortex_a53: CPU workaround for 827319 was missing!
> INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
> INFO:    BL31: Preparing for EL3 exit to normal world
> INFO:    Entry point address = 0x200000
> INFO:    SPSR = 0x3c9
>
>
> U-Boot 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
>
> Model: Pine64 RockPro64
> DRAM:  3.9 GiB
> MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
> Loading Environment from MMC... *** Warning - bad CRC, using default environment
>
> In:    serial@ff1a0000
> Out:   serial@ff1a0000
> Err:   serial@ff1a0000
> Model: Pine64 RockPro64
> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> Net:  
> Error: ethernet@fe300000 address not set.
> eth-1: ethernet@fe300000
> Hit any key to stop autoboot:  0
> switch to partitions #0, OK
> mmc0(part 0) is current device
> ** No partition table - mmc 0 **
> switch to partitions #0, OK
> mmc1 is current device
> ** Invalid partition 1 **
> starting USB...
> Bus usb@fe380000: USB EHCI 1.00
> Bus usb@fe3c0000: USB EHCI 1.00
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> scanning bus usb@fe380000 for devices... 2 USB Device(s) found
> scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
>        scanning usb for storage devices... 1 Storage Device(s) found
>
> Device 0: Vendor: Lexar    Rev: 1100 Prod: USB Flash Drive
>             Type: Removable Hard Disk
>             Capacity: 7634.0 MB = 7.4 GB (15634432 x 512)
> ... is now current device
> Scanning usb 0:1...
> Found EFI removable media binary efi/boot/bootaa64.efi
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> Scanning disk [hidden email]...
> Scanning disk [hidden email]...
> Scanning disk usb_mass_storage.lun0...
> Found 5 disks
> BootOrder not defined
> EFI boot manager: Cannot load any image
> 165119 bytes read in 56 ms (2.8 MiB/s)
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> disks: sd0* sd1 sd2
> >> OpenBSD/arm64 BOOTAA64 0.20
> boot>
> cannot open sd0a:/etc/random.seed: No such file or directory
> booting sd0a:/bsd: 2228484+623928+8770112+752864 [180632+109+521472+201593]=0xff1d68
> Host not halted after 16000 microseconds.
> type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8
> type 0x7 pa 0x4200000 va 0x4200000 pages 0x3eec attr 0x8
> type 0x4 pa 0x80ec000 va 0x80ec000 pages 0x28 attr 0x8
> type 0x7 pa 0x8114000 va 0x8114000 pages 0xec0a6 attr 0x8
> type 0x2 pa 0xf41ba000 va 0xf41ba000 pages 0xc33 attr 0x8
> type 0x7 pa 0xf4ded000 va 0xf4ded000 pages 0x1 attr 0x8
> type 0x2 pa 0xf4dee000 va 0xf4dee000 pages 0x100 attr 0x8
> type 0x1 pa 0xf4eee000 va 0xf4eee000 pages 0x29 attr 0x8
> type 0x0 pa 0xf4f17000 va 0xf4f17000 pages 0x7 attr 0x8
> type 0x4 pa 0xf4f1e000 va 0xf4f1e000 pages 0x1 attr 0x8
> type 0x0 pa 0xf4f1f000 va 0xf4f1f000 pages 0x2 attr 0x8
> type 0x6 pa 0xf4f21000 va 0xa3863000 pages 0x1 attr 0x8000000000000008
> type 0x0 pa 0xf4f22000 va 0xf4f22000 pages 0x3 attr 0x8
> type 0x4 pa 0xf4f25000 va 0xf4f25000 pages 0x2 attr 0x8
> type 0x6 pa 0xf4f27000 va 0xa3869000 pages 0x1 attr 0x8000000000000008
> type 0x2 pa 0xf4f28000 va 0xf4f28000 pages 0x3018 attr 0x8
> type 0x5 pa 0xf7f40000 va 0xa6882000 pages 0x10 attr 0x8000000000000008
> type 0x2 pa 0xf7f50000 va 0xf7f50000 pages 0xb0 attr 0x8
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California.  All rights reserved.
> Copyright (c) 1995-2019 OpenBSD. All rights reserved.  https://www.OpenBSD.org
>
> OpenBSD 6.6-current (RAMDISK) #333: Thu Nov 28 01:12:25 MST 2019
>     [hidden email]:/usr/src/sys/arch/arm64/compile/RAMDISK
> real mem  = 4093190144 (3903MB)
> avail mem = 3891441664 (3711MB)
> mainbus0 at root: Pine64 RockPro64
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
> cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu0: 512KB 64b/line 16-way L2 cache
> efi0 at mainbus0: UEFI 2.8
> efi0: Das U-Boot rev 0x20191000
> psci0 at mainbus0: PSCI 1.1, SMCCC 1.1
> agintc0 at mainbus0 sec shift 3:3 nirq 288 nredist 6: "interrupt-controller"
> agintcmsi0 at agintc0
> syscon0 at mainbus0: "qos"
> syscon1 at mainbus0: "qos"
> syscon2 at mainbus0: "qos"
> syscon3 at mainbus0: "qos"
> syscon4 at mainbus0: "qos"
> syscon5 at mainbus0: "qos"
> syscon6 at mainbus0: "qos"
> syscon7 at mainbus0: "qos"
> syscon8 at mainbus0: "qos"
> syscon9 at mainbus0: "qos"
> syscon10 at mainbus0: "qos"
> syscon11 at mainbus0: "qos"
> syscon12 at mainbus0: "qos"
> syscon13 at mainbus0: "qos"
> syscon14 at mainbus0: "qos"
> syscon15 at mainbus0: "qos"
> syscon16 at mainbus0: "qos"
> syscon17 at mainbus0: "qos"
> syscon18 at mainbus0: "qos"
> syscon19 at mainbus0: "qos"
> syscon20 at mainbus0: "qos"
> syscon21 at mainbus0: "qos"
> syscon22 at mainbus0: "qos"
> syscon23 at mainbus0: "qos"
> syscon24 at mainbus0: "qos"
> syscon25 at mainbus0: "power-management"
> "power-controller" at syscon25 not configured
> syscon26 at mainbus0: "syscon"
> "io-domains" at syscon26 not configured
> syscon27 at mainbus0: "syscon"
> syscon28 at mainbus0: "syscon"
> rkclock0 at mainbus0
> rkclock1 at mainbus0
> syscon29 at mainbus0: "syscon"
> "io-domains" at syscon29 not configured
> "usb2-phy" at syscon29 not configured
> "usb2-phy" at syscon29 not configured
> "phy" at syscon29 not configured
> rkpinctrl0 at mainbus0: "pinctrl"
> rkgpio0 at rkpinctrl0
> rkgpio1 at rkpinctrl0
> rkgpio2 at rkpinctrl0
> rkgpio3 at rkpinctrl0
> rkgpio4 at rkpinctrl0
> "fit-images" at mainbus0 not configured
> "pmu_a53" at mainbus0 not configured
> "pmu_a72" at mainbus0 not configured
> agtimer0 at mainbus0: tick rate 24000 KHz
> "xin24m" at mainbus0 not configured
> simplebus0 at mainbus0: "amba"
> "dma-controller" at simplebus0 not configured
> "dma-controller" at simplebus0 not configured
> dwge0 at mainbus0: address ff:ff:ff:ff:ff:ff
> rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6
> dwmmc0 at mainbus0: 50 MHz base clock
> sdmmc0 at dwmmc0: 4-bit, sd high-speed, mmc high-speed, dma
> sdhc0 at mainbus0
> sdhc0: SDHC 3.0, 200 MHz base clock
> sdmmc1 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
> ehci0 at mainbus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
> ohci0 at mainbus0: version 1.0
> ehci1 at mainbus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
> ohci1 at mainbus0: version 1.0
> rkdwusb0 at mainbus0: "usb"
> xhci0 at rkdwusb0, xHCI 1.10
> usb2 at xhci0: USB revision 3.0
> uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
> rkdwusb1 at mainbus0: "usb"
> xhci1 at rkdwusb1, xHCI 1.10
> usb3 at xhci1: USB revision 3.0
> uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
> "saradc" at mainbus0 not configured
> rkiic0 at mainbus0
> iic0 at rkiic0
> rkiic1 at mainbus0
> iic1 at rkiic1
> com0 at mainbus0: ns16550, no working fifo
> com1 at mainbus0: ns16550, no working fifo
> com1: console
> "thermal-zones" at mainbus0 not configured
> "tsadc" at mainbus0 not configured
> rkiic2 at mainbus0
> iic2 at rkiic2
> rkpmic0 at iic2 addr 0x1b: RK808
> "silergy,syr827" at iic2 addr 0x40 not configured
> "silergy,syr828" at iic2 addr 0x41 not configured
> rkiic3 at mainbus0
> iic3 at rkiic3
> fusbtc0 at iic3 addr 0x22
> "pwm" at mainbus0 not configured
> "pwm" at mainbus0 not configured
> "dmc" at mainbus0 not configured
> "efuse" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "watchdog" at mainbus0 not configured
> "rktimer" at mainbus0 not configured
> "i2s" at mainbus0 not configured
> "i2s" at mainbus0 not configured
> "i2s" at mainbus0 not configured
> "vop" at mainbus0 not configured
> "iommu" at mainbus0 not configured
> "vop" at mainbus0 not configured
> "iommu" at mainbus0 not configured
> "hdmi" at mainbus0 not configured
> "gpu" at mainbus0 not configured
> "opp-table0" at mainbus0 not configured
> "opp-table1" at mainbus0 not configured
> "opp-table2" at mainbus0 not configured
> "external-gmac-clock" at mainbus0 not configured
> "gpio-keys" at mainbus0 not configured
> "leds" at mainbus0 not configured
> "sdio-pwrseq" at mainbus0 not configured
> "vcc12v-dcin" at mainbus0 not configured
> "vcc1v8-s3" at mainbus0 not configured
> "vcc3v3-pcie-regulator" at mainbus0 not configured
> "vcc3v3-sys" at mainbus0 not configured
> "vcc5v0-host-regulator" at mainbus0 not configured
> "vcc5v0-typec-regulator" at mainbus0 not configured
> "vcc5v0-sys" at mainbus0 not configured
> "vcc5v0-usb" at mainbus0 not configured
> "vdd-log" at mainbus0 not configured
> usb4 at ohci0: USB revision 1.0
> uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
> usb5 at ohci1: USB revision 1.0
> uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
> scsibus0 at sdmmc0: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SC16G, 0080> removable
> sd0: 15193MB, 512 bytes/sector, 31116288 sectors
> scsibus1 at sdmmc1: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4064, 0000> removable
> sd1: 59640MB, 512 bytes/sector, 122142720 sectors
> umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive" rev 2.10/11.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus2 at umass0: 2 targets, initiator 0
> sd2 at scsibus2 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable serial.05dca838E89K3FOCINZ7
> sd2: 7634MB, 512 bytes/sector, 15634432 sectors
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> bootfile: sd0a:/bsd
> boot device: sd0
> root on rd0a swap on rd0b dump on rd0b
> WARNING: preposterous clock chip time
> WARNING: CHECK AND RESET THE DATE!
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/arm64 6.6 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I
> At any prompt except password prompts you can escape to a shell by
> typing '!'. Default answers are shown in []'s and are selected by
> pressing RETURN.  You can exit this program at any time by pressing
> Control-C, but this can leave your system in an inconsistent state.
>
> Terminal type? [vt220]
> System hostname? (short form, e.g. 'foo') pinu
>
> Available network interfaces are: dwge0 vlan0.
> Which network interface do you wish to configure? (or 'done') [dwge0]
> IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp]
> dwge0: no link....
> dwge0: xxx.xxx.xxx.12 lease accepted from xxx.xxx.xxx.254 (14:0c:xxx:xx:xx:xx)
> IPv6 address for dwge0? (or 'autoconf' or 'none') [none] autoconf
> Available network interfaces are: dwge0 vlan0.
> Which network interface do you wish to configure? (or 'done') [done]
> DNS domain name? (e.g. 'example.com') [my.domain] burelli.home
> Using DNS nameservers at xxx.xxx.xxx.254 8.8.8.8
>
> Password for root account? (will not echo)
> Password for root account? (again)
> Start sshd(8) by default? [yes]
> Setup a user? (enter a lower-case loginname, or 'no') [no] olivier
> Full name for user olivier? [oliv] Olivier Burelli
> Password for user olivier? (will not echo)
> Password for user olivier? (again)
> WARNING: root is targeted by password guessing attacks, pubkeys are safer.
> Allow root ssh login? (yes, no, prohibit-password) [no]
> What timezone are you in? ('?' for list) [Europe/Paris]
>
> Available disks are: sd0 sd1 sd2.
> Which disk is the root disk? ('?' for details) [sd0] ?
> sd0: SD/MMC, SC16G, 0080  (14.8G)
> sd1: Sandisk, DA4064, 0000  (58.2G)
> sd2: Lexar, USB Flash Drive, 1100 serial.05dca838E89K3FOCINZ7 (7.5G)
> Available disks are: sd0 sd1 sd2.
> Which disk is the root disk? ('?' for details) [sd0] sd1
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT  
> Use (W)hole disk or (E)dit the MBR? [whole] e
>
> You will now create one MBR partition to contain your OpenBSD data
> and one MBR partition on which the OpenBSD boot program is located.
> Neither partition will overlap any other partition.
>
> The OpenBSD MBR partition will have an id of 'A6' and the boot MBR
> partition will have an id of 'C' (msdos).
> The boot partition will be at least 16MB and be the first 'MSDOS'
> partition on the disk.
>
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT  
> Enter 'help' for information
> sd1: 1> reinit
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
>  1: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
>  2: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
> *3: A6      0   1   2 -   7602 254  63 [          64:   122142131 ] OpenBSD    
> Use 'write' to update disk.
> sd1*: 1> write
> Writing MBR at offset 0.
> sd1: 1> q
> No OpenBSD partition in MBR, try again.
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT  
>  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT  
> Use (W)hole disk or (E)dit the MBR? [whole]
>
>
>
>
> --
> burelli.fr <[hidden email]>


--
burelli.fr <[hidden email]>

Reply | Threaded
Open this post in threaded view
|

Re: [ROCKP64] emmc Install

Kurt Miller-4
In reply to this post by Olivier BURELLI
On Thu, 2019-11-28 at 23:29 +0100, burelli.fr wrote:

> Hello,
>
> I tried to install current on RockPro64 to eMMC.
>
> _ I used the firmware provided by Marc (on microSD): https://marc.info/?l=openbsd-arm&m=156114869709200&w=2
> _ I used an usb stick for miniroot
>
> Once arrived to choose the whole disk... Impossible to write the eMMC disk. I tried to force via reinit... without
> success.
>
> _ A reason ? (i will try (to validate the installation process) to install OpenBSD on the sd card.
>

I found the information regarding the eMMC here:
https://wiki.pine64.org/index.php/ROCKPro64#Disable_eMMC
to be wrong. I found that I needed to do the exact opposite
to get the eMMC working.

Try putting a jumper on SW4 before booting and installing.

> Thanks in advance.
>
>
> ********************
> * Installation log *
> ********************
> cu -s 115200 -l /dev/cuaU0    
> Connected to /dev/cuaU0 (speed 115200)
>
> U-Boot TPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31)
> Trying to boot from BOOTROM
> Returning to boot ROM...
>
> U-Boot SPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
> Trying to boot from MMC1
> NOTICE:  BL31: v2.1(debug):2.1
> NOTICE:  BL31: Built : 21:16:08, Jul  4 2019
> INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
> INFO:    plat_rockchip_pmu_init(1596): pd status 3e
> INFO:    BL31: Initializing runtime services
> WARNING: BL31: cortex_a53: CPU workaround for 819472 was missing!
> WARNING: BL31: cortex_a53: CPU workaround for 824069 was missing!
> WARNING: BL31: cortex_a53: CPU workaround for 827319 was missing!
> INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
> INFO:    BL31: Preparing for EL3 exit to normal world
> INFO:    Entry point address = 0x200000
> INFO:    SPSR = 0x3c9
>
>
> U-Boot 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
>
> Model: Pine64 RockPro64
> DRAM:  3.9 GiB
> MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
> Loading Environment from MMC... *** Warning - bad CRC, using default environment
>
> In:    serial@ff1a0000
> Out:   serial@ff1a0000
> Err:   serial@ff1a0000
> Model: Pine64 RockPro64
> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> Net:   
> Error: ethernet@fe300000 address not set.
> eth-1: ethernet@fe300000
> Hit any key to stop autoboot:  0 
> switch to partitions #0, OK
> mmc0(part 0) is current device
> ** No partition table - mmc 0 **
> switch to partitions #0, OK
> mmc1 is current device
> ** Invalid partition 1 **
> starting USB...
> Bus usb@fe380000: USB EHCI 1.00
> Bus usb@fe3c0000: USB EHCI 1.00
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> scanning bus usb@fe380000 for devices... 2 USB Device(s) found
> scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
>        scanning usb for storage devices... 1 Storage Device(s) found
>
> Device 0: Vendor: Lexar    Rev: 1100 Prod: USB Flash Drive 
>             Type: Removable Hard Disk
>             Capacity: 7634.0 MB = 7.4 GB (15634432 x 512)
> ... is now current device
> Scanning usb 0:1...
> Found EFI removable media binary efi/boot/bootaa64.efi
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> Scanning disk [hidden email]...
> Scanning disk [hidden email]...
> Scanning disk usb_mass_storage.lun0...
> Found 5 disks
> BootOrder not defined
> EFI boot manager: Cannot load any image
> 165119 bytes read in 56 ms (2.8 MiB/s)
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> disks: sd0* sd1 sd2
> >
> > >
> > > OpenBSD/arm64 BOOTAA64 0.20
> boot> 
> cannot open sd0a:/etc/random.seed: No such file or directory
> booting sd0a:/bsd: 2228484+623928+8770112+752864 [180632+109+521472+201593]=0xff1d68
> Host not halted after 16000 microseconds.
> type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8
> type 0x7 pa 0x4200000 va 0x4200000 pages 0x3eec attr 0x8
> type 0x4 pa 0x80ec000 va 0x80ec000 pages 0x28 attr 0x8
> type 0x7 pa 0x8114000 va 0x8114000 pages 0xec0a6 attr 0x8
> type 0x2 pa 0xf41ba000 va 0xf41ba000 pages 0xc33 attr 0x8
> type 0x7 pa 0xf4ded000 va 0xf4ded000 pages 0x1 attr 0x8
> type 0x2 pa 0xf4dee000 va 0xf4dee000 pages 0x100 attr 0x8
> type 0x1 pa 0xf4eee000 va 0xf4eee000 pages 0x29 attr 0x8
> type 0x0 pa 0xf4f17000 va 0xf4f17000 pages 0x7 attr 0x8
> type 0x4 pa 0xf4f1e000 va 0xf4f1e000 pages 0x1 attr 0x8
> type 0x0 pa 0xf4f1f000 va 0xf4f1f000 pages 0x2 attr 0x8
> type 0x6 pa 0xf4f21000 va 0xa3863000 pages 0x1 attr 0x8000000000000008
> type 0x0 pa 0xf4f22000 va 0xf4f22000 pages 0x3 attr 0x8
> type 0x4 pa 0xf4f25000 va 0xf4f25000 pages 0x2 attr 0x8
> type 0x6 pa 0xf4f27000 va 0xa3869000 pages 0x1 attr 0x8000000000000008
> type 0x2 pa 0xf4f28000 va 0xf4f28000 pages 0x3018 attr 0x8
> type 0x5 pa 0xf7f40000 va 0xa6882000 pages 0x10 attr 0x8000000000000008
> type 0x2 pa 0xf7f50000 va 0xf7f50000 pages 0xb0 attr 0x8
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California.  All rights reserved.
> Copyright (c) 1995-2019 OpenBSD. All rights reserved.  https://www.OpenBSD.org
>
> OpenBSD 6.6-current (RAMDISK) #333: Thu Nov 28 01:12:25 MST 2019
>     [hidden email]:/usr/src/sys/arch/arm64/compile/RAMDISK
> real mem  = 4093190144 (3903MB)
> avail mem = 3891441664 (3711MB)
> mainbus0 at root: Pine64 RockPro64
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
> cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu0: 512KB 64b/line 16-way L2 cache
> efi0 at mainbus0: UEFI 2.8
> efi0: Das U-Boot rev 0x20191000
> psci0 at mainbus0: PSCI 1.1, SMCCC 1.1
> agintc0 at mainbus0 sec shift 3:3 nirq 288 nredist 6: "interrupt-controller"
> agintcmsi0 at agintc0
> syscon0 at mainbus0: "qos"
> syscon1 at mainbus0: "qos"
> syscon2 at mainbus0: "qos"
> syscon3 at mainbus0: "qos"
> syscon4 at mainbus0: "qos"
> syscon5 at mainbus0: "qos"
> syscon6 at mainbus0: "qos"
> syscon7 at mainbus0: "qos"
> syscon8 at mainbus0: "qos"
> syscon9 at mainbus0: "qos"
> syscon10 at mainbus0: "qos"
> syscon11 at mainbus0: "qos"
> syscon12 at mainbus0: "qos"
> syscon13 at mainbus0: "qos"
> syscon14 at mainbus0: "qos"
> syscon15 at mainbus0: "qos"
> syscon16 at mainbus0: "qos"
> syscon17 at mainbus0: "qos"
> syscon18 at mainbus0: "qos"
> syscon19 at mainbus0: "qos"
> syscon20 at mainbus0: "qos"
> syscon21 at mainbus0: "qos"
> syscon22 at mainbus0: "qos"
> syscon23 at mainbus0: "qos"
> syscon24 at mainbus0: "qos"
> syscon25 at mainbus0: "power-management"
> "power-controller" at syscon25 not configured
> syscon26 at mainbus0: "syscon"
> "io-domains" at syscon26 not configured
> syscon27 at mainbus0: "syscon"
> syscon28 at mainbus0: "syscon"
> rkclock0 at mainbus0
> rkclock1 at mainbus0
> syscon29 at mainbus0: "syscon"
> "io-domains" at syscon29 not configured
> "usb2-phy" at syscon29 not configured
> "usb2-phy" at syscon29 not configured
> "phy" at syscon29 not configured
> rkpinctrl0 at mainbus0: "pinctrl"
> rkgpio0 at rkpinctrl0
> rkgpio1 at rkpinctrl0
> rkgpio2 at rkpinctrl0
> rkgpio3 at rkpinctrl0
> rkgpio4 at rkpinctrl0
> "fit-images" at mainbus0 not configured
> "pmu_a53" at mainbus0 not configured
> "pmu_a72" at mainbus0 not configured
> agtimer0 at mainbus0: tick rate 24000 KHz
> "xin24m" at mainbus0 not configured
> simplebus0 at mainbus0: "amba"
> "dma-controller" at simplebus0 not configured
> "dma-controller" at simplebus0 not configured
> dwge0 at mainbus0: address ff:ff:ff:ff:ff:ff
> rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6
> dwmmc0 at mainbus0: 50 MHz base clock
> sdmmc0 at dwmmc0: 4-bit, sd high-speed, mmc high-speed, dma
> sdhc0 at mainbus0
> sdhc0: SDHC 3.0, 200 MHz base clock
> sdmmc1 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
> ehci0 at mainbus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
> ohci0 at mainbus0: version 1.0
> ehci1 at mainbus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
> ohci1 at mainbus0: version 1.0
> rkdwusb0 at mainbus0: "usb"
> xhci0 at rkdwusb0, xHCI 1.10
> usb2 at xhci0: USB revision 3.0
> uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
> rkdwusb1 at mainbus0: "usb"
> xhci1 at rkdwusb1, xHCI 1.10
> usb3 at xhci1: USB revision 3.0
> uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
> "saradc" at mainbus0 not configured
> rkiic0 at mainbus0
> iic0 at rkiic0
> rkiic1 at mainbus0
> iic1 at rkiic1
> com0 at mainbus0: ns16550, no working fifo
> com1 at mainbus0: ns16550, no working fifo
> com1: console
> "thermal-zones" at mainbus0 not configured
> "tsadc" at mainbus0 not configured
> rkiic2 at mainbus0
> iic2 at rkiic2
> rkpmic0 at iic2 addr 0x1b: RK808
> "silergy,syr827" at iic2 addr 0x40 not configured
> "silergy,syr828" at iic2 addr 0x41 not configured
> rkiic3 at mainbus0
> iic3 at rkiic3
> fusbtc0 at iic3 addr 0x22
> "pwm" at mainbus0 not configured
> "pwm" at mainbus0 not configured
> "dmc" at mainbus0 not configured
> "efuse" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "watchdog" at mainbus0 not configured
> "rktimer" at mainbus0 not configured
> "i2s" at mainbus0 not configured
> "i2s" at mainbus0 not configured
> "i2s" at mainbus0 not configured
> "vop" at mainbus0 not configured
> "iommu" at mainbus0 not configured
> "vop" at mainbus0 not configured
> "iommu" at mainbus0 not configured
> "hdmi" at mainbus0 not configured
> "gpu" at mainbus0 not configured
> "opp-table0" at mainbus0 not configured
> "opp-table1" at mainbus0 not configured
> "opp-table2" at mainbus0 not configured
> "external-gmac-clock" at mainbus0 not configured
> "gpio-keys" at mainbus0 not configured
> "leds" at mainbus0 not configured
> "sdio-pwrseq" at mainbus0 not configured
> "vcc12v-dcin" at mainbus0 not configured
> "vcc1v8-s3" at mainbus0 not configured
> "vcc3v3-pcie-regulator" at mainbus0 not configured
> "vcc3v3-sys" at mainbus0 not configured
> "vcc5v0-host-regulator" at mainbus0 not configured
> "vcc5v0-typec-regulator" at mainbus0 not configured
> "vcc5v0-sys" at mainbus0 not configured
> "vcc5v0-usb" at mainbus0 not configured
> "vdd-log" at mainbus0 not configured
> usb4 at ohci0: USB revision 1.0
> uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
> usb5 at ohci1: USB revision 1.0
> uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
> scsibus0 at sdmmc0: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SC16G, 0080> removable
> sd0: 15193MB, 512 bytes/sector, 31116288 sectors
> scsibus1 at sdmmc1: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4064, 0000> removable
> sd1: 59640MB, 512 bytes/sector, 122142720 sectors
> umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive" rev 2.10/11.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus2 at umass0: 2 targets, initiator 0
> sd2 at scsibus2 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable serial.05dca838E89K3FOCINZ7
> sd2: 7634MB, 512 bytes/sector, 15634432 sectors
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> bootfile: sd0a:/bsd
> boot device: sd0
> root on rd0a swap on rd0b dump on rd0b
> WARNING: preposterous clock chip time
> WARNING: CHECK AND RESET THE DATE!
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/arm64 6.6 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I
> At any prompt except password prompts you can escape to a shell by
> typing '!'. Default answers are shown in []'s and are selected by
> pressing RETURN.  You can exit this program at any time by pressing
> Control-C, but this can leave your system in an inconsistent state.
>
> Terminal type? [vt220] 
> System hostname? (short form, e.g. 'foo') pinu
>
> Available network interfaces are: dwge0 vlan0.
> Which network interface do you wish to configure? (or 'done') [dwge0] 
> IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp] 
> dwge0: no link....
> dwge0: xxx.xxx.xxx.12 lease accepted from xxx.xxx.xxx.254 (14:0c:xxx:xx:xx:xx)
> IPv6 address for dwge0? (or 'autoconf' or 'none') [none] autoconf
> Available network interfaces are: dwge0 vlan0.
> Which network interface do you wish to configure? (or 'done') [done] 
> DNS domain name? (e.g. 'example.com') [my.domain] burelli.home
> Using DNS nameservers at xxx.xxx.xxx.254 8.8.8.8
>
> Password for root account? (will not echo) 
> Password for root account? (again) 
> Start sshd(8) by default? [yes] 
> Setup a user? (enter a lower-case loginname, or 'no') [no] olivier
> Full name for user olivier? [oliv] Olivier Burelli
> Password for user olivier? (will not echo) 
> Password for user olivier? (again) 
> WARNING: root is targeted by password guessing attacks, pubkeys are safer.
> Allow root ssh login? (yes, no, prohibit-password) [no] 
> What timezone are you in? ('?' for list) [Europe/Paris] 
>
> Available disks are: sd0 sd1 sd2.
> Which disk is the root disk? ('?' for details) [sd0] ?
> sd0: SD/MMC, SC16G, 0080  (14.8G)
> sd1: Sandisk, DA4064, 0000  (58.2G)
> sd2: Lexar, USB Flash Drive, 1100 serial.05dca838E89K3FOCINZ7 (7.5G)
> Available disks are: sd0 sd1 sd2.
> Which disk is the root disk? ('?' for details) [sd0] sd1
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT   
> Use (W)hole disk or (E)dit the MBR? [whole] e
>
> You will now create one MBR partition to contain your OpenBSD data
> and one MBR partition on which the OpenBSD boot program is located.
> Neither partition will overlap any other partition.
>
> The OpenBSD MBR partition will have an id of 'A6' and the boot MBR
> partition will have an id of 'C' (msdos).
> The boot partition will be at least 16MB and be the first 'MSDOS'
> partition on the disk.
>
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT   
> Enter 'help' for information
> sd1: 1> reinit
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
>  1: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
>  2: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
> *3: A6      0   1   2 -   7602 254  63 [          64:   122142131 ] OpenBSD     
> Use 'write' to update disk.
> sd1*: 1> write
> Writing MBR at offset 0.
> sd1: 1> q
> No OpenBSD partition in MBR, try again.
> Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> Offset: 0 Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> -------------------------------------------------------------------------------
>  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
>  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT   
> Use (W)hole disk or (E)dit the MBR? [whole]
>
>
>
>

Reply | Threaded
Open this post in threaded view
|

Re: [ROCKP64] emmc Install

Olivier BURELLI
On Mon, 02 Dec 2019 08:41:35 -0500
Kurt Miller <[hidden email]> wrote:

> On Thu, 2019-11-28 at 23:29 +0100, burelli.fr wrote:
> > Hello,
> >
> > I tried to install current on RockPro64 to eMMC.
> >
> > _ I used the firmware provided by Marc (on microSD): https://marc.info/?l=openbsd-arm&m=156114869709200&w=2
> > _ I used an usb stick for miniroot
> >
> > Once arrived to choose the whole disk... Impossible to write the eMMC disk. I tried to force via reinit... without
> > success.
> >
> > _ A reason ? (i will try (to validate the installation process) to install OpenBSD on the sd card.
> >
>
> I found the information regarding the eMMC here:
> https://wiki.pine64.org/index.php/ROCKPro64#Disable_eMMC
> to be wrong. I found that I needed to do the exact opposite
> to get the eMMC working.
>
> Try putting a jumper on SW4 before booting and installing.
>
Hi thanks for your feedback.

I already read this documentation. I tried also all the possibilities, no Jumper, Jumper removed after 2sec, keep the jumper...

I can not write on it. I think to an eMMC issue :

#fdisk -e sd1
fdisk: Can't read sector 0!

#dd if=idbloader.img of=/dev/sd1c seek=64
dd: /dev/sd1c: Input/output error
1+0 records in
0+0 records out
0 bytes transferred in 0.010 secs (0 bytes/sec)

#dd if=u-boot.itb of=/dev/sd1c seek=16384
dd: /dev/sd1c: Input/output error
1+0 records in
0+0 records out
0 bytes transferred in 0.010 secs (0 bytes/sec)

I will test the eMMC or another one, once i will have the parts...

Thank you

> > Thanks in advance.
> >
> >
> > ********************
> > * Installation log *
> > ********************
> > cu -s 115200 -l /dev/cuaU0    
> > Connected to /dev/cuaU0 (speed 115200)
> >
> > U-Boot TPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31)
> > Trying to boot from BOOTROM
> > Returning to boot ROM...
> >
> > U-Boot SPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
> > Trying to boot from MMC1
> > NOTICE:  BL31: v2.1(debug):2.1
> > NOTICE:  BL31: Built : 21:16:08, Jul  4 2019
> > INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
> > INFO:    plat_rockchip_pmu_init(1596): pd status 3e
> > INFO:    BL31: Initializing runtime services
> > WARNING: BL31: cortex_a53: CPU workaround for 819472 was missing!
> > WARNING: BL31: cortex_a53: CPU workaround for 824069 was missing!
> > WARNING: BL31: cortex_a53: CPU workaround for 827319 was missing!
> > INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
> > INFO:    BL31: Preparing for EL3 exit to normal world
> > INFO:    Entry point address = 0x200000
> > INFO:    SPSR = 0x3c9
> >
> >
> > U-Boot 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
> >
> > Model: Pine64 RockPro64
> > DRAM:  3.9 GiB
> > MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
> > Loading Environment from MMC... *** Warning - bad CRC, using default environment
> >
> > In:    serial@ff1a0000
> > Out:   serial@ff1a0000
> > Err:   serial@ff1a0000
> > Model: Pine64 RockPro64
> > rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> > Net:   
> > Error: ethernet@fe300000 address not set.
> > eth-1: ethernet@fe300000
> > Hit any key to stop autoboot:  0 
> > switch to partitions #0, OK
> > mmc0(part 0) is current device
> > ** No partition table - mmc 0 **
> > switch to partitions #0, OK
> > mmc1 is current device
> > ** Invalid partition 1 **
> > starting USB...
> > Bus usb@fe380000: USB EHCI 1.00
> > Bus usb@fe3c0000: USB EHCI 1.00
> > Bus dwc3: Register 2000140 NbrPorts 2
> > Starting the controller
> > USB XHCI 1.10
> > Bus dwc3: Register 2000140 NbrPorts 2
> > Starting the controller
> > USB XHCI 1.10
> > scanning bus usb@fe380000 for devices... 2 USB Device(s) found
> > scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
> > scanning bus dwc3 for devices... 1 USB Device(s) found
> > scanning bus dwc3 for devices... 1 USB Device(s) found
> >        scanning usb for storage devices... 1 Storage Device(s) found
> >
> > Device 0: Vendor: Lexar    Rev: 1100 Prod: USB Flash Drive 
> >             Type: Removable Hard Disk
> >             Capacity: 7634.0 MB = 7.4 GB (15634432 x 512)
> > ... is now current device
> > Scanning usb 0:1...
> > Found EFI removable media binary efi/boot/bootaa64.efi
> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> > Scanning disk [hidden email]...
> > Scanning disk [hidden email]...
> > Scanning disk usb_mass_storage.lun0...
> > Found 5 disks
> > BootOrder not defined
> > EFI boot manager: Cannot load any image
> > 165119 bytes read in 56 ms (2.8 MiB/s)
> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> > disks: sd0* sd1 sd2
> > >
> > > >
> > > > OpenBSD/arm64 BOOTAA64 0.20
> > boot> 
> > cannot open sd0a:/etc/random.seed: No such file or directory
> > booting sd0a:/bsd: 2228484+623928+8770112+752864 [180632+109+521472+201593]=0xff1d68
> > Host not halted after 16000 microseconds.
> > type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8
> > type 0x7 pa 0x4200000 va 0x4200000 pages 0x3eec attr 0x8
> > type 0x4 pa 0x80ec000 va 0x80ec000 pages 0x28 attr 0x8
> > type 0x7 pa 0x8114000 va 0x8114000 pages 0xec0a6 attr 0x8
> > type 0x2 pa 0xf41ba000 va 0xf41ba000 pages 0xc33 attr 0x8
> > type 0x7 pa 0xf4ded000 va 0xf4ded000 pages 0x1 attr 0x8
> > type 0x2 pa 0xf4dee000 va 0xf4dee000 pages 0x100 attr 0x8
> > type 0x1 pa 0xf4eee000 va 0xf4eee000 pages 0x29 attr 0x8
> > type 0x0 pa 0xf4f17000 va 0xf4f17000 pages 0x7 attr 0x8
> > type 0x4 pa 0xf4f1e000 va 0xf4f1e000 pages 0x1 attr 0x8
> > type 0x0 pa 0xf4f1f000 va 0xf4f1f000 pages 0x2 attr 0x8
> > type 0x6 pa 0xf4f21000 va 0xa3863000 pages 0x1 attr 0x8000000000000008
> > type 0x0 pa 0xf4f22000 va 0xf4f22000 pages 0x3 attr 0x8
> > type 0x4 pa 0xf4f25000 va 0xf4f25000 pages 0x2 attr 0x8
> > type 0x6 pa 0xf4f27000 va 0xa3869000 pages 0x1 attr 0x8000000000000008
> > type 0x2 pa 0xf4f28000 va 0xf4f28000 pages 0x3018 attr 0x8
> > type 0x5 pa 0xf7f40000 va 0xa6882000 pages 0x10 attr 0x8000000000000008
> > type 0x2 pa 0xf7f50000 va 0xf7f50000 pages 0xb0 attr 0x8
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > The Regents of the University of California.  All rights reserved.
> > Copyright (c) 1995-2019 OpenBSD. All rights reserved.  https://www.OpenBSD.org
> >
> > OpenBSD 6.6-current (RAMDISK) #333: Thu Nov 28 01:12:25 MST 2019
> >     [hidden email]:/usr/src/sys/arch/arm64/compile/RAMDISK
> > real mem  = 4093190144 (3903MB)
> > avail mem = 3891441664 (3711MB)
> > mainbus0 at root: Pine64 RockPro64
> > cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
> > cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> > cpu0: 512KB 64b/line 16-way L2 cache
> > efi0 at mainbus0: UEFI 2.8
> > efi0: Das U-Boot rev 0x20191000
> > psci0 at mainbus0: PSCI 1.1, SMCCC 1.1
> > agintc0 at mainbus0 sec shift 3:3 nirq 288 nredist 6: "interrupt-controller"
> > agintcmsi0 at agintc0
> > syscon0 at mainbus0: "qos"
> > syscon1 at mainbus0: "qos"
> > syscon2 at mainbus0: "qos"
> > syscon3 at mainbus0: "qos"
> > syscon4 at mainbus0: "qos"
> > syscon5 at mainbus0: "qos"
> > syscon6 at mainbus0: "qos"
> > syscon7 at mainbus0: "qos"
> > syscon8 at mainbus0: "qos"
> > syscon9 at mainbus0: "qos"
> > syscon10 at mainbus0: "qos"
> > syscon11 at mainbus0: "qos"
> > syscon12 at mainbus0: "qos"
> > syscon13 at mainbus0: "qos"
> > syscon14 at mainbus0: "qos"
> > syscon15 at mainbus0: "qos"
> > syscon16 at mainbus0: "qos"
> > syscon17 at mainbus0: "qos"
> > syscon18 at mainbus0: "qos"
> > syscon19 at mainbus0: "qos"
> > syscon20 at mainbus0: "qos"
> > syscon21 at mainbus0: "qos"
> > syscon22 at mainbus0: "qos"
> > syscon23 at mainbus0: "qos"
> > syscon24 at mainbus0: "qos"
> > syscon25 at mainbus0: "power-management"
> > "power-controller" at syscon25 not configured
> > syscon26 at mainbus0: "syscon"
> > "io-domains" at syscon26 not configured
> > syscon27 at mainbus0: "syscon"
> > syscon28 at mainbus0: "syscon"
> > rkclock0 at mainbus0
> > rkclock1 at mainbus0
> > syscon29 at mainbus0: "syscon"
> > "io-domains" at syscon29 not configured
> > "usb2-phy" at syscon29 not configured
> > "usb2-phy" at syscon29 not configured
> > "phy" at syscon29 not configured
> > rkpinctrl0 at mainbus0: "pinctrl"
> > rkgpio0 at rkpinctrl0
> > rkgpio1 at rkpinctrl0
> > rkgpio2 at rkpinctrl0
> > rkgpio3 at rkpinctrl0
> > rkgpio4 at rkpinctrl0
> > "fit-images" at mainbus0 not configured
> > "pmu_a53" at mainbus0 not configured
> > "pmu_a72" at mainbus0 not configured
> > agtimer0 at mainbus0: tick rate 24000 KHz
> > "xin24m" at mainbus0 not configured
> > simplebus0 at mainbus0: "amba"
> > "dma-controller" at simplebus0 not configured
> > "dma-controller" at simplebus0 not configured
> > dwge0 at mainbus0: address ff:ff:ff:ff:ff:ff
> > rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6
> > dwmmc0 at mainbus0: 50 MHz base clock
> > sdmmc0 at dwmmc0: 4-bit, sd high-speed, mmc high-speed, dma
> > sdhc0 at mainbus0
> > sdhc0: SDHC 3.0, 200 MHz base clock
> > sdmmc1 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
> > ehci0 at mainbus0
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
> > ohci0 at mainbus0: version 1.0
> > ehci1 at mainbus0
> > usb1 at ehci1: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
> > ohci1 at mainbus0: version 1.0
> > rkdwusb0 at mainbus0: "usb"
> > xhci0 at rkdwusb0, xHCI 1.10
> > usb2 at xhci0: USB revision 3.0
> > uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
> > rkdwusb1 at mainbus0: "usb"
> > xhci1 at rkdwusb1, xHCI 1.10
> > usb3 at xhci1: USB revision 3.0
> > uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
> > "saradc" at mainbus0 not configured
> > rkiic0 at mainbus0
> > iic0 at rkiic0
> > rkiic1 at mainbus0
> > iic1 at rkiic1
> > com0 at mainbus0: ns16550, no working fifo
> > com1 at mainbus0: ns16550, no working fifo
> > com1: console
> > "thermal-zones" at mainbus0 not configured
> > "tsadc" at mainbus0 not configured
> > rkiic2 at mainbus0
> > iic2 at rkiic2
> > rkpmic0 at iic2 addr 0x1b: RK808
> > "silergy,syr827" at iic2 addr 0x40 not configured
> > "silergy,syr828" at iic2 addr 0x41 not configured
> > rkiic3 at mainbus0
> > iic3 at rkiic3
> > fusbtc0 at iic3 addr 0x22
> > "pwm" at mainbus0 not configured
> > "pwm" at mainbus0 not configured
> > "dmc" at mainbus0 not configured
> > "efuse" at mainbus0 not configured
> > "phy" at mainbus0 not configured
> > "phy" at mainbus0 not configured
> > "watchdog" at mainbus0 not configured
> > "rktimer" at mainbus0 not configured
> > "i2s" at mainbus0 not configured
> > "i2s" at mainbus0 not configured
> > "i2s" at mainbus0 not configured
> > "vop" at mainbus0 not configured
> > "iommu" at mainbus0 not configured
> > "vop" at mainbus0 not configured
> > "iommu" at mainbus0 not configured
> > "hdmi" at mainbus0 not configured
> > "gpu" at mainbus0 not configured
> > "opp-table0" at mainbus0 not configured
> > "opp-table1" at mainbus0 not configured
> > "opp-table2" at mainbus0 not configured
> > "external-gmac-clock" at mainbus0 not configured
> > "gpio-keys" at mainbus0 not configured
> > "leds" at mainbus0 not configured
> > "sdio-pwrseq" at mainbus0 not configured
> > "vcc12v-dcin" at mainbus0 not configured
> > "vcc1v8-s3" at mainbus0 not configured
> > "vcc3v3-pcie-regulator" at mainbus0 not configured
> > "vcc3v3-sys" at mainbus0 not configured
> > "vcc5v0-host-regulator" at mainbus0 not configured
> > "vcc5v0-typec-regulator" at mainbus0 not configured
> > "vcc5v0-sys" at mainbus0 not configured
> > "vcc5v0-usb" at mainbus0 not configured
> > "vdd-log" at mainbus0 not configured
> > usb4 at ohci0: USB revision 1.0
> > uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
> > usb5 at ohci1: USB revision 1.0
> > uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
> > scsibus0 at sdmmc0: 2 targets, initiator 0
> > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SC16G, 0080> removable
> > sd0: 15193MB, 512 bytes/sector, 31116288 sectors
> > scsibus1 at sdmmc1: 2 targets, initiator 0
> > sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4064, 0000> removable
> > sd1: 59640MB, 512 bytes/sector, 122142720 sectors
> > umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive" rev 2.10/11.00 addr 2
> > umass0: using SCSI over Bulk-Only
> > scsibus2 at umass0: 2 targets, initiator 0
> > sd2 at scsibus2 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable serial.05dca838E89K3FOCINZ7
> > sd2: 7634MB, 512 bytes/sector, 15634432 sectors
> > softraid0 at root
> > scsibus3 at softraid0: 256 targets
> > bootfile: sd0a:/bsd
> > boot device: sd0
> > root on rd0a swap on rd0b dump on rd0b
> > WARNING: preposterous clock chip time
> > WARNING: CHECK AND RESET THE DATE!
> > erase ^?, werase ^W, kill ^U, intr ^C, status ^T
> >
> > Welcome to the OpenBSD/arm64 6.6 installation program.
> > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I
> > At any prompt except password prompts you can escape to a shell by
> > typing '!'. Default answers are shown in []'s and are selected by
> > pressing RETURN.  You can exit this program at any time by pressing
> > Control-C, but this can leave your system in an inconsistent state.
> >
> > Terminal type? [vt220] 
> > System hostname? (short form, e.g. 'foo') pinu
> >
> > Available network interfaces are: dwge0 vlan0.
> > Which network interface do you wish to configure? (or 'done') [dwge0] 
> > IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp] 
> > dwge0: no link....
> > dwge0: xxx.xxx.xxx.12 lease accepted from xxx.xxx.xxx.254 (14:0c:xxx:xx:xx:xx)
> > IPv6 address for dwge0? (or 'autoconf' or 'none') [none] autoconf
> > Available network interfaces are: dwge0 vlan0.
> > Which network interface do you wish to configure? (or 'done') [done] 
> > DNS domain name? (e.g. 'example.com') [my.domain] burelli.home
> > Using DNS nameservers at xxx.xxx.xxx.254 8.8.8.8
> >
> > Password for root account? (will not echo) 
> > Password for root account? (again) 
> > Start sshd(8) by default? [yes] 
> > Setup a user? (enter a lower-case loginname, or 'no') [no] olivier
> > Full name for user olivier? [oliv] Olivier Burelli
> > Password for user olivier? (will not echo) 
> > Password for user olivier? (again) 
> > WARNING: root is targeted by password guessing attacks, pubkeys are safer.
> > Allow root ssh login? (yes, no, prohibit-password) [no] 
> > What timezone are you in? ('?' for list) [Europe/Paris] 
> >
> > Available disks are: sd0 sd1 sd2.
> > Which disk is the root disk? ('?' for details) [sd0] ?
> > sd0: SD/MMC, SC16G, 0080  (14.8G)
> > sd1: Sandisk, DA4064, 0000  (58.2G)
> > sd2: Lexar, USB Flash Drive, 1100 serial.05dca838E89K3FOCINZ7 (7.5G)
> > Available disks are: sd0 sd1 sd2.
> > Which disk is the root disk? ('?' for details) [sd0] sd1
> > Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> > Offset: 0 Signature: 0xAA55
> >             Starting         Ending         LBA Info:
> >  #: id      C   H   S -      C   H   S [       start:        size ]
> > -------------------------------------------------------------------------------
> >  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT   
> > Use (W)hole disk or (E)dit the MBR? [whole] e
> >
> > You will now create one MBR partition to contain your OpenBSD data
> > and one MBR partition on which the OpenBSD boot program is located.
> > Neither partition will overlap any other partition.
> >
> > The OpenBSD MBR partition will have an id of 'A6' and the boot MBR
> > partition will have an id of 'C' (msdos).
> > The boot partition will be at least 16MB and be the first 'MSDOS'
> > partition on the disk.
> >
> > Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> > Offset: 0 Signature: 0xAA55
> >             Starting         Ending         LBA Info:
> >  #: id      C   H   S -      C   H   S [       start:        size ]
> > -------------------------------------------------------------------------------
> >  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT   
> > Enter 'help' for information
> > sd1: 1> reinit
> > Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> > Offset: 0 Signature: 0xAA55
> >             Starting         Ending         LBA Info:
> >  #: id      C   H   S -      C   H   S [       start:        size ]
> > -------------------------------------------------------------------------------
> >  0: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
> >  1: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
> >  2: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
> > *3: A6      0   1   2 -   7602 254  63 [          64:   122142131 ] OpenBSD     
> > Use 'write' to update disk.
> > sd1*: 1> write
> > Writing MBR at offset 0.
> > sd1: 1> q
> > No OpenBSD partition in MBR, try again.
> > Disk: sd1 geometry: 7603/255/63 [122142720 Sectors]
> > Offset: 0 Signature: 0xAA55
> >             Starting         Ending         LBA Info:
> >  #: id      C   H   S -      C   H   S [       start:        size ]
> > -------------------------------------------------------------------------------
> >  0: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  1: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  2: FF 267349  89   4 - 267349  89   2 [  4294967295:  4294967295 ] Xenix BBT   
> >  3: FF 267349  89   4 -  46077  37  38 [  4294967295:   740229375 ] Xenix BBT   
> > Use (W)hole disk or (E)dit the MBR? [whole]
> >
> >
> >
> >


--
burelli.fr <[hidden email]>