Pandaboard: Installation kernel panics

classic Classic list List threaded Threaded
3 messages Options
Reply | Threaded
Open this post in threaded view
|

Pandaboard: Installation kernel panics

Marcus Lindemann
Hi,
I'm trying to install armv7 on a pandaboard. Both, the
miniroot-panda-63.fs and miniroot-panda-64.fs from Aug 24th panic with
the following message:
panic: pool_do_get: pvepl: page empty

I'd appreciate any suggestions.
Full console output below.
Thanks
Marcus

U-Boot SPL 2018.03 (Mar 19 2018 - 23:59:15 -0600)
OMAP4430-GP ES2.1
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!


U-Boot 2018.03 (Mar 19 2018 - 23:59:15 -0600)

CPU  : OMAP4430-GP ES2.1
Board: OMAP4 Panda
I2C:   ready
DRAM:  1 GiB
MMC:   OMAP SD/MMC: 0
Loading Environment from FAT... *** Warning - bad CRC, using default
environment

Failed (-5)
Net:   No ethernet found.
Hit any key to stop autoboot:  2  1  0
## Error: "init_console" not defined
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
56740 bytes read in 9 ms (6 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
Scanning disks on usb...
Disk usb0 not ready
Disk usb1 not ready
Disk usb2 not ready
Disk usb3 not ready
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 3 disks
89348 bytes read in 13 ms (6.6 MiB/s)
## Starting EFI application at 82000000 ...
>> OpenBSD/armv7 BOOTARM 1.1
|/-boot>
\|/cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd:
-\|/-2781028\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|+452120/-\|/-\|/-\|/-\|/-\|/-\|/-\|+8055196/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|+447940/
[187370-\|/-\|/-\|/+107+206496-\|/-\|/-\|/-+181684\|/-\|/-\|/]=0xbbea20

OpenBSD/armv7 booting ...
arg0 0xc0ebea20 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80ebf000, free_pages = 258369 (0x0003f141)
IRQ stack: p0x80eed000 v0xc0eed000
ABT stack: p0x80eee000 v0xc0eee000
UND stack: p0x80eef000 v0xc0eef000
SVC stack: p0x80ef0000 v0xc0ef0000
Creating L1 page table at 0x80ec0000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2018 OpenBSD. All rights reserved.
https://www.OpenBSD.org

OpenBSD 6.4-beta (RAMDISK) #38: Thu Aug 23 19:39:32 MDT 2018
    [hidden email]:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem  = 1073741824 (1024MB)
avail mem = 1037381632 (989MB)
mainbus0 at root: TI OMAP4 PandaBoard
cpu0 at mainbus0: ARM Cortex-A9 r1p2 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160, ncpu 2: "interrupt-controller"
omwugen0 at mainbus0
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "cm1"
simplebus3 at simplebus1: "cm2"
simplebus4 at simplebus1: "scm"
syscon0 at simplebus4: "scm_conf"
simplebus5 at simplebus1: "scm"
syscon1 at simplebus5: "omap4_padconf_global"
ompinmux0 at simplebus5
simplebus6 at simplebus5: "omap4_padconf_global"
simplebus7 at simplebus1: "l4"
simplebus8 at simplebus7: "padconf"
ompinmux1 at simplebus8
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.10
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.10
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.10
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.10
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 8-bit
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.0
omdog1 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "TI OMAP EHCI root hub" rev
2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0000> SCSI2 0/direct removable
sd0: 15240MB, 512 bytes/sector, 31211520 sectors
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems
product 0x9514" rev 2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address 02:03:01:8b:14:e0
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
softraid0 at root
scsibus1 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...

U-Boot SPL 2018.03 (Mar 19 2018 - 23:59:15 -0600)
OMAP4430-GP ES2.1
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!


U-Boot 2018.03 (Mar 19 2018 - 23:59:15 -0600)

CPU  : OMAP4430-GP ES2.1
Board: OMAP4 Panda
I2C:   ready
DRAM:  1 GiB
MMC:   OMAP SD/MMC: 0
Loading Environment from FAT... *** Warning - bad CRC, using default
environment
Reply | Threaded
Open this post in threaded view
|

Re: Pandaboard: Installation kernel panics

Jonathan Gray-11
On Sat, Aug 25, 2018 at 08:56:37AM +0200, Marcus Lindemann wrote:

> Hi,
> I'm trying to install armv7 on a pandaboard. Both, the
> miniroot-panda-63.fs and miniroot-panda-64.fs from Aug 24th panic with
> the following message:
> panic: pool_do_get: pvepl: page empty
>
> I'd appreciate any suggestions.
> Full console output below.
> Thanks
> Marcus

Do you consistently see it?

With the same U-Boot/snapshot version on a PandaBoard-ES

U-Boot SPL 2018.03 (Mar 19 2018 - 23:59:15 -0600)
OMAP4460-GP ES1.1
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!


U-Boot 2018.03 (Mar 19 2018 - 23:59:15 -0600)

CPU  : OMAP4460-GP ES1.1
Board: OMAP4 Panda
I2C:   ready
DRAM:  1 GiB
MMC:   OMAP SD/MMC: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment

Failed (-5)
Net:   No ethernet found.
Hit any key to stop autoboot:  0
## Error: "init_console" not defined
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** Unable to read file boot.scr **
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
57332 bytes read in 4 ms (13.7 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
Scanning disks on usb...
Disk usb0 not ready
Disk usb1 not ready
Disk usb2 not ready
Disk usb3 not ready
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 3 disks
89348 bytes read in 7 ms (12.2 MiB/s)
## Starting EFI application at 82000000 ...
>> OpenBSD/armv7 BOOTARM 1.1
boot> bsd.rd
booting sd0a:bsd.rd: 2781028+452120+8055196+447940\[187370+107+206496+181684]=0xbbea20

OpenBSD/armv7 booting ...
arg0 0xc0ebea20 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80ebf000, free_pages = 258369 (0x0003f141)
IRQ stack: p0x80eed000 v0xc0eed000
ABT stack: p0x80eee000 v0xc0eee000
UND stack: p0x80eef000 v0xc0eef000
SVC stack: p0x80ef0000 v0xc0ef0000
Creating L1 page table at 0x80ec0000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2018 OpenBSD. All rights reserved.  https://www.OpenBSD.org

OpenBSD 6.4-beta (RAMDISK) #38: Thu Aug 23 19:39:32 MDT 2018
    [hidden email]:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem  = 1073741824 (1024MB)
avail mem = 1037377536 (989MB)
mainbus0 at root: TI OMAP4 PandaBoard-ES
cpu0 at mainbus0: ARM Cortex-A9 r2p10 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4460
amptimer0: adjusting clock: new tick rate 350000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160, ncpu 2: "interrupt-controller"
omwugen0 at mainbus0
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "cm1"
simplebus3 at simplebus1: "cm2"
simplebus4 at simplebus1: "scm"
syscon0 at simplebus4: "scm_conf"
simplebus5 at simplebus1: "scm"
syscon1 at simplebus5: "omap4_padconf_global"
ompinmux0 at simplebus5
simplebus6 at simplebus5: "omap4_padconf_global"
simplebus7 at simplebus1: "l4"
simplebus8 at simplebus7: "padconf"
ompinmux1 at simplebus8
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.11
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.11
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.11
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.11
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 8-bit
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.1
omdog1 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SP16G, 0080> SCSI2 0/direct removable
sd0: 15193MB, 512 bytes/sector, 31116288 sectors
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems product 0x9514" rev 2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address 02:22:01:5d:0d:70
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x0001f0, model 0x000c
softraid0 at root
scsibus1 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T

Welcome to the OpenBSD/armv7 6.4 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s
#

Reply | Threaded
Open this post in threaded view
|

Re: Pandaboard: Installation kernel panics

Marcus Lindemann
Hi,
yes, I see this consistently, it actually falls into a reboot loop
(U-Boot ==> starting the install kernel ==> panic ==> U-Boot and the
cycle goes on). My board is Pandaboard Rev A2.

BR
Marcus

Am 26.08.2018 um 06:12 schrieb Jonathan Gray:

> On Sat, Aug 25, 2018 at 08:56:37AM +0200, Marcus Lindemann wrote:
>> Hi,
>> I'm trying to install armv7 on a pandaboard. Both, the
>> miniroot-panda-63.fs and miniroot-panda-64.fs from Aug 24th panic with
>> the following message:
>> panic: pool_do_get: pvepl: page empty
>>
>> I'd appreciate any suggestions.
>> Full console output below.
>> Thanks
>> Marcus
>
> Do you consistently see it?
>
> With the same U-Boot/snapshot version on a PandaBoard-ES
>
> U-Boot SPL 2018.03 (Mar 19 2018 - 23:59:15 -0600)
> OMAP4460-GP ES1.1
> Trying to boot from MMC1
> SPL: Please implement spl_start_uboot() for your board
> SPL: Direct Linux boot not active!
>
>
> U-Boot 2018.03 (Mar 19 2018 - 23:59:15 -0600)
>
> CPU  : OMAP4460-GP ES1.1
> Board: OMAP4 Panda
> I2C:   ready
> DRAM:  1 GiB
> MMC:   OMAP SD/MMC: 0
> Loading Environment from FAT... *** Warning - bad CRC, using default environment
>
> Failed (-5)
> Net:   No ethernet found.
> Hit any key to stop autoboot:  0
> ## Error: "init_console" not defined
> switch to partitions #0, OK
> mmc0 is current device
> SD/MMC found on device 0
> ** Unable to read file boot.scr **
> ** Unable to read file uEnv.txt **
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> 57332 bytes read in 4 ms (13.7 MiB/s)
> Found EFI removable media binary efi/boot/bootarm.efi
> Scanning disks on usb...
> Disk usb0 not ready
> Disk usb1 not ready
> Disk usb2 not ready
> Disk usb3 not ready
> Scanning disks on mmc...
> MMC Device 1 not found
> MMC Device 2 not found
> MMC Device 3 not found
> Found 3 disks
> 89348 bytes read in 7 ms (12.2 MiB/s)
> ## Starting EFI application at 82000000 ...
>>> OpenBSD/armv7 BOOTARM 1.1
> boot> bsd.rd
> booting sd0a:bsd.rd: 2781028+452120+8055196+447940\[187370+107+206496+181684]=0xbbea20
>
> OpenBSD/armv7 booting ...
> arg0 0xc0ebea20 arg1 0xae7 arg2 0x88000000
> Allocating page tables
> freestart = 0x80ebf000, free_pages = 258369 (0x0003f141)
> IRQ stack: p0x80eed000 v0xc0eed000
> ABT stack: p0x80eee000 v0xc0eee000
> UND stack: p0x80eef000 v0xc0eef000
> SVC stack: p0x80ef0000 v0xc0ef0000
> Creating L1 page table at 0x80ec0000
> Mapping kernel
> Constructing L2 page tables
> undefined page pmap board type: 2791
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California.  All rights reserved.
> Copyright (c) 1995-2018 OpenBSD. All rights reserved.  https://www.OpenBSD.org
>
> OpenBSD 6.4-beta (RAMDISK) #38: Thu Aug 23 19:39:32 MDT 2018
>     [hidden email]:/usr/src/sys/arch/armv7/compile/RAMDISK
> real mem  = 1073741824 (1024MB)
> avail mem = 1037377536 (989MB)
> mainbus0 at root: TI OMAP4 PandaBoard-ES
> cpu0 at mainbus0: ARM Cortex-A9 r2p10 (ARMv7)
> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
> cortex0 at mainbus0
> amptimer0 at cortex0: tick rate 396000 KHz
> armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
> omap0 at mainbus0
> omapid0 at omap0: omap4460
> amptimer0: adjusting clock: new tick rate 350000 KHz
> prcm0 at omap0 rev 0.0
> ampintc0 at mainbus0 nirq 160, ncpu 2: "interrupt-controller"
> omwugen0 at mainbus0
> simplebus0 at mainbus0: "ocp"
> simplebus1 at simplebus0: "l4"
> simplebus2 at simplebus1: "cm1"
> simplebus3 at simplebus1: "cm2"
> simplebus4 at simplebus1: "scm"
> syscon0 at simplebus4: "scm_conf"
> simplebus5 at simplebus1: "scm"
> syscon1 at simplebus5: "omap4_padconf_global"
> ompinmux0 at simplebus5
> simplebus6 at simplebus5: "omap4_padconf_global"
> simplebus7 at simplebus1: "l4"
> simplebus8 at simplebus7: "padconf"
> ompinmux1 at simplebus8
> omgpio0 at simplebus0: rev 0.1
> gpio0 at omgpio0: 32 pins
> omgpio1 at simplebus0: rev 0.1
> gpio1 at omgpio1: 32 pins
> omgpio2 at simplebus0: rev 0.1
> gpio2 at omgpio2: 32 pins
> omgpio3 at simplebus0: rev 0.1
> gpio3 at omgpio3: 32 pins
> omgpio4 at simplebus0: rev 0.1
> gpio4 at omgpio4: 32 pins
> omgpio5 at simplebus0: rev 0.1
> gpio5 at omgpio5: 32 pins
> com0 at simplebus0: ti16750, 64 byte fifo
> com0: probed fifo depth: 0 bytes
> com1 at simplebus0: ti16750, 64 byte fifo
> com1: probed fifo depth: 0 bytes
> com2 at simplebus0: ti16750, 64 byte fifo
> com2: console
> com3 at simplebus0: ti16750, 64 byte fifo
> com3: probed fifo depth: 0 bytes
> tiiic0 at simplebus0 rev 0.11
> iic0 at tiiic0
> "ti,twl6030" at iic0 addr 0x48 not configured
> "ti,twl6040" at iic0 addr 0x4b not configured
> tiiic1 at simplebus0 rev 0.11
> iic1 at tiiic1
> tiiic2 at simplebus0 rev 0.11
> iic2 at tiiic2
> "ti,eeprom" at iic2 addr 0x50 not configured
> tiiic3 at simplebus0 rev 0.11
> iic3 at tiiic3
> ommmc0 at simplebus0
> sdmmc0 at ommmc0: 8-bit
> ommmc1 at simplebus0
> sdmmc1 at ommmc1: 1-bit
> omdog0 at simplebus0 rev 0.1
> omdog1 at simplebus0 rev 0.0
> omehci0 at simplebus0
> usb0 at omehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
> sdmmc1: can't supply clock
> sdmmc1: can't enable card
> scsibus0 at sdmmc0: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SP16G, 0080> SCSI2 0/direct removable
> sd0: 15193MB, 512 bytes/sector, 31116288 sectors
> uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems product 0x9514" rev 2.00/2.00 addr 2
> smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems SMSC9512/14" rev 2.00/2.00 addr 3
> smsc0: address 02:22:01:5d:0d:70
> ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x0001f0, model 0x000c
> softraid0 at root
> scsibus1 at softraid0: 256 targets
> bootfile: sd0a:/bsd
> boot device: sd0
> root on rd0a swap on rd0b dump on rd0b
> WARNING: CHECK AND RESET THE DATE!
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/armv7 6.4 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s
> #
>