OpenBSD on Xeon 3360

classic Classic list List threaded Threaded
2 messages Options
Reply | Threaded
Open this post in threaded view
|

OpenBSD on Xeon 3360

Matthias Pfeifer-4
Hello misc!

I have installed OpenBSD on an new machine with
intel Xeon 3360.

I am using the mp kernel with acpi disabled (machine died blue
with acpi enabled, UCK config is saved after boot).
But it is just cpu0 running. Any hints?

Here is my dmesg


OpenBSD 4.5 (GENERIC.MP) #108: Sat Feb 28 14:58:58 MST 2009
    [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC.MP
RTC BIOS diagnostic error 6<invalid_time>
cpu0: Intel(R) Xeon(R) CPU X3360 @ 2.83GHz ("GenuineIntel" 686-class) 2.83 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE
2,SS,HTT,TM,SBF,SSE3,TM2
real mem  = 3754446848 (3580MB)
avail mem = 3646255104 (3477MB)
RTC BIOS diagnostic error 6<invalid_time>
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/12/07, SMBIOS rev. 2.5 @ 0xdfdfa000 (63 entries)
bios0: vendor Intel Corporation version "S3200X38.86B.00.00.0042.042820081723" date 04/28/2008
bios0: Intel Corporation S3210SH
acpi at bios0 function 0x0 not configured
mpbios0 at bios0: Intel MP Specification 1.4
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: unknown i686 EBL_CR_POWERON value 3 (0x420c0800)
cpu0: apic clock running at 332MHz
mpbios0: bus 0 is type PCI  
mpbios0: bus 1 is type PCI  
mpbios0: bus 2 is type PCI  
mpbios0: bus 3 is type PCI  
mpbios0: bus 4 is type PCI  
mpbios0: bus 5 is type PCI  
mpbios0: bus 6 is type PCI  
mpbios0: bus 7 is type ISA  
ioapic0 at mainbus0: apid 5 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 5
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1200 0xc9800/0x1000 0xca800/0x1000
ipmi at mainbus0 not configured
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 3200/3210 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "Intel 3200/3210 PCIE" rev 0x00: apic 5 int 16 (irq 11)
pci1 at ppb0 bus 1
ppb1 at pci1 dev 0 function 0 "Intel IOP333 PCIE-PCIX" rev 0x00
pci2 at ppb1 bus 2
arc0 at pci2 dev 14 function 0 "Areca ARC-1210" rev 0x00: apic 5 int 18 (irq 9)
arc0: 4 ports, 256MB SDRAM, firmware V1.46 2009-01-06
scsibus0 at arc0: 16 targets
sd0 at scsibus0 targ 0 lun 0: <Areca, ARC-1210-VOL#00, R001> SCSI3 0/direct fixed
sd0: 238418MB, 512 bytes/sec, 488281088 sec total
ppb2 at pci1 dev 0 function 2 "Intel IOP333 PCIE-PCIX" rev 0x00
pci3 at ppb2 bus 3
em0 at pci0 dev 25 function 0 "Intel ICH9 IGP AMT" rev 0x02: apic 5 int 20 (irq 11), address 00:15:17:b3:56:1
2
uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x02: apic 5 int 18 (irq 9)
uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x02: apic 5 int 21 (irq 10)
uhci2 at pci0 dev 26 function 2 "Intel 82801I USB" rev 0x02: apic 5 int 17 (irq 10)
ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x02: apic 5 int 17 (irq 10)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb3 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02pci_intr_map: bus 0 dev 28 func 0 pin 1; line 11
pci_intr_map: no MP mapping found: irq 11
pci4 at ppb3 bus 4
ppb4 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02: apic 5 int 11 (irq 11)
pci5 at ppb4 bus 5
vga1 at pci5 dev 0 function 0 "Matrox MGA G200e (ServerEngines)" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci3 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: apic 5 int 23 (irq 11)
uhci4 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: apic 5 int 19 (irq 11)
uhci5 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: apic 5 int 18 (irq 9)
ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: apic 5 int 23 (irq 11)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb5 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92
pci6 at ppb5 bus 6
em1 at pci6 dev 2 function 0 "Intel PRO/1000MT (82541GI)" rev 0x05: apic 5 int 18 (irq 9), address 00:15:17:b
3:56:10
ichpcib0 at pci0 dev 31 function 0 "Intel 82801IR LPC" rev 0x02: PM disabled
pciide0 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA, channel 0 configured to native-PCI, chan
nel 1 configured to native-PCI
pciide0: using apic 5 int 21 (irq 10) for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <ATAPI, iHDS118 5, RL03> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x02: apic 5 int 18 (irq 9)
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem1 at iic0 addr 0x52: 2GB DDR2 SDRAM non-parity PC2-6400CL5
pciide1 at pci0 dev 31 function 5 "Intel 82801I SATA" rev 0x02: DMA, channel 0 wired to native-PCI, channel 1
 wired to native-PCI
pciide1: using apic 5 int 21 (irq 10) for native-PCI interrupt
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
mtrr: Pentium Pro MTRR support
softraid0 at root
root on sd0a swap on sd0b dump on sd0b



--
Hugh!

Reply | Threaded
Open this post in threaded view
|

Re: OpenBSD on Xeon 3360

Stuart Henderson
On 2009-08-10, Matthias <[hidden email]> wrote:
> Hello misc!
>
> I have installed OpenBSD on an new machine with
> intel Xeon 3360.
>
> I am using the mp kernel with acpi disabled (machine died blue
> with acpi enabled, UCK config is saved after boot).
> But it is just cpu0 running. Any hints?

try -current.