Quantcast

Olinuxino Allwinner A10 installation successful l, but boot again into yet another Installation ?

Next Topic
 
classic Classic list List threaded Threaded
4 messages Options
Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

Olinuxino Allwinner A10 installation successful l, but boot again into yet another Installation ?

Patrick YU
After successfully installing on an Olinuxino A10 board via the SD card
onto a Toshiba disk with the following MBR partition table, I rebooted
and again offered to perform another OpenBSD installation.  Why ?  
Thanks in advance for any enlightenment !

-- Patrick

# fdisk sd0
Disk: sd0       geometry: 121601/255/63 [1953525168 Sectors]
Offset: 0       Signature: 0xAA55
             Starting         Ending         LBA Info:
  #: id      C   H   S -      C   H   S [       start:        size ]
-------------------------------------------------------------------------------
  0: 83      0  32  33 -  58743 224  41 [        2048:   943718400 ]
Linux files*
  1: 0C  58743 224  42 -  58746 109  51 [   943720448:       40960 ]
FAT32L
  2: A6  58746 109  52 - 118795 153  14 [   943761408:   964689920 ]
OpenBSD
  3: 00      0   0   0 -      0   0   0 [           0:           0 ]
unused

U-Boot 2017.03 (Apr 03 2017 - 11:14:00 -0600) Allwinner Technology

CPU:   Allwinner A10 (SUN4I)
Model: Olimex A10-OLinuXino-LIME
I2C:   ready
DRAM:  512 MiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
SCSI:  Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net:   eth0: ethernet@01c0b000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
USB2:   USB EHCI 1.00
USB3:   USB OHCI 1.0
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning bus 3 for devices... 2 USB Device(s) found
        scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
64684 bytes read in 41 ms (1.5 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
## Starting EFI application at 42000000 ...
Scanning disks on scsi...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 6 disks
>> OpenBSD/armv7 BOOTARM 0.5
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151556+7983908+438824 [80+301248+143324]=0xa84fd4

...
sd0 at scsibus0 targ 0 lun 0: <ATA, TOSHIBA MQ01ABD1, AX00> SCSI3
0/direct fixed naa.5000039514a065a8
sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
...
sd1 at scsibus1 targ 1 lun 0: <Sandisk, SA08G, 0021> SCSI2 0/direct
removable
sd1: 7420MB, 512 bytes/sector, 15196160 sectors
axe0 at uhub0 port 1 configuration 1 interface 0 "ASIX Electronics
AX88772B" rev 2.00/0.01 addr 2
axe0: AX88772B, address 00:00:00:00:00:01
ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
0x000ec6, model 0x0008
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: preposterous clock chip time
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T

Welcome to the OpenBSD/armv7 6.1 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? shell

Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

Re: Olinuxino Allwinner A10 installation successful l, but boot again into yet another Installation ?

soko.tica
There is a Linux files partition on your sd0 that is marked bootable. It
shouldn't be there. FAT32L should, I believe, be marked bootable.

You probably haven't cleared up the disk before the installation properly.
Clear it by fdisk, mark all partitions blank (zero) and repeat the
installation.

On Thu, Apr 20, 2017 at 5:26 AM, Patrick YU <[hidden email]> wrote:

> After successfully installing on an Olinuxino A10 board via the SD card
> onto a Toshiba disk with the following MBR partition table, I rebooted and
> again offered to perform another OpenBSD installation.  Why ?  Thanks in
> advance for any enlightenment !
>
> -- Patrick
>
> # fdisk sd0
> Disk: sd0       geometry: 121601/255/63 [1953525168 Sectors]
> Offset: 0       Signature: 0xAA55
>             Starting         Ending         LBA Info:
>  #: id      C   H   S -      C   H   S [       start:        size ]
> ------------------------------------------------------------
> -------------------
>  0: 83      0  32  33 -  58743 224 41 [        2048:   943718400 ] Linux
> files*
>  1: 0C  58743 224 42 -  58746 109 51 [   943720448:       40960 ] FAT32L
>  2: A6  58746 109  52 - 118795 153  14 [   943761408:   964689920 ] OpenBSD
>  3: 00      0   0   0 -      0   0   0 [           0:           0 ] unused
>
> U-Boot 2017.03 (Apr 03 2017 - 11:14:00 -0600) Allwinner Technology
>
> CPU:   Allwinner A10 (SUN4I)
> Model: Olimex A10-OLinuXino-LIME
> I2C:   ready
> DRAM:  512 MiB
> MMC:   SUNXI SD/MMC: 0
> *** Warning - bad CRC, using default environment
>
> In:    serial
> Out:   serial
> Err:   serial
> SCSI:  Target spinup took 0 ms.
> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> flags: ncq stag pm led clo only pmp pio slum part ccc apst
> Net:   eth0: ethernet@01c0b000
> starting USB...
> USB0:   USB EHCI 1.00
> USB1:   USB OHCI 1.0
> USB2:   USB EHCI 1.00
> USB3:   USB OHCI 1.0
> scanning bus 0 for devices... 2 USB Device(s) found
> scanning bus 2 for devices... 1 USB Device(s) found
> scanning bus 1 for devices... 1 USB Device(s) found
> scanning bus 3 for devices... 2 USB Device(s) found
>        scanning usb for storage devices... 0 Storage Device(s) found
> Hit any key to stop autoboot:  0
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> Found EFI removable media binary efi/boot/bootarm.efi
> reading efi/boot/bootarm.efi
> 64684 bytes read in 41 ms (1.5 MiB/s)
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> ## Starting EFI application at 42000000 ...
> Scanning disks on scsi...
> Scanning disks on usb...
> Scanning disks on mmc...
> MMC Device 1 not found
> MMC Device 2 not found
> MMC Device 3 not found
> Found 6 disks
>
>> OpenBSD/armv7 BOOTARM 0.5
>>>
>> boot>
> cannot open sd0a:/etc/random.seed: No such file or directory
> booting sd0a:/bsd: 2151556+7983908+438824 [80+301248+143324]=0xa84fd4
>
> ...
> sd0 at scsibus0 targ 0 lun 0: <ATA, TOSHIBA MQ01ABD1, AX00> SCSI3 0/direct
> fixed naa.5000039514a065a8
> sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
> ...
> sd1 at scsibus1 targ 1 lun 0: <Sandisk, SA08G, 0021> SCSI2 0/direct
> removable
> sd1: 7420MB, 512 bytes/sector, 15196160 sectors
> axe0 at uhub0 port 1 configuration 1 interface 0 "ASIX Electronics
> AX88772B" rev 2.00/0.01 addr 2
> axe0: AX88772B, address 00:00:00:00:00:01
> ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
> 0x000ec6, model 0x0008
> boot device: sd0
> root on rd0a swap on rd0b dump on rd0b
> WARNING: preposterous clock chip time
> WARNING: CHECK AND RESET THE DATE!
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/armv7 6.1 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? shell
>
>
Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

Re: Olinuxino Allwinner A10 installation successful l, but boot again into yet another Installation ?

Patrick YU
Thanks Soko -- setting to default boot on the OpenBSD partition didn't
help.
Instead, I had to specify the root device manually to the boot loader
using the -a flag.  Without such, I notice the root device is still
pointing to the SD card ??
>> boot device: sd0
>> root on rd0a swap on rd0b dump on rd0b

At the bootloader, I use the flag -a
OpenBSD/armv7 BOOTARM 0.5
boot> b sd0a:/bsd -a
Then OpenBSD proposes the root device to be sd0a, for me to confirm.  
How can I fix this ?

Issue now is pfctl invocations in /etc/rc is triggering
pfctl: /dev/pf: Device not configured --> does the device pf in
/etc/MAKEDEV require a different numbers for the my A10 device ??

The /etc/rc boot-up continued with failed start-up of daemons:
    starting early daemons: syslogd(failed) pflogd(failed).
    starting RPC daemons:.
    savecore: can't find device 20/14778624
    checking quotas: done.
    kvm_mkdb: can't open /dev/ksyms
    clearing /tmp
    kern.securelevel: 0 -> 1
    creating runtime link editor directory cache.
    preserving editor files.
    starting network daemons: sshd(failed) smtpd(failed) sndiod(failed).
    ifconfig: SIOCSIFGATTR: No such file or directory
    starting local daemons: cron(failed).

I had to commented-out  ntpd to let the boot-up arriving at the login:
prompt !!

Any advice / comment is appreciated !

-- Patrick
On 2017-04-21 09:22, soko.tica wrote:

> There is a Linux files partition on your sd0 that is marked bootable.
> It
> shouldn't be there. FAT32L should, I believe, be marked bootable.
>
> You probably haven't cleared up the disk before the installation
> properly.
> Clear it by fdisk, mark all partitions blank (zero) and repeat the
> installation.
>
> On Thu, Apr 20, 2017 at 5:26 AM, Patrick YU <patrickyu> wrote:
>
>> After successfully installing on an Olinuxino A10 board via the SD
>> card
>> onto a Toshiba disk with the following MBR partition table, I rebooted
>> and
>> again offered to perform another OpenBSD installation.  Why ?  Thanks
>> in
>> advance for any enlightenment !
>>
>> -- Patrick
>>
>> # fdisk sd0
>> Disk: sd0       geometry: 121601/255/63 [1953525168 Sectors]
>> Offset: 0       Signature: 0xAA55
>>             Starting         Ending         LBA Info:
>>  #: id      C   H   S -      C   H   S [       start:        size ]
>> ------------------------------------------------------------
>> -------------------
>>  0: 83      0  32  33 -  58743 224 41 [        2048:   943718400 ]
>> Linux
>> files*
>>  1: 0C  58743 224 42 -  58746 109 51 [   943720448:       40960 ]
>> FAT32L
>>  2: A6  58746 109  52 - 118795 153  14 [   943761408:   964689920 ]
>> OpenBSD
>>  3: 00      0   0   0 -      0   0   0 [           0:           0 ]
>> unused
>>
>> U-Boot 2017.03 (Apr 03 2017 - 11:14:00 -0600) Allwinner Technology
>>
>> CPU:   Allwinner A10 (SUN4I)
>> Model: Olimex A10-OLinuXino-LIME
>> I2C:   ready
>> DRAM:  512 MiB
>> MMC:   SUNXI SD/MMC: 0
>> *** Warning - bad CRC, using default environment
>>
>> In:    serial
>> Out:   serial
>> Err:   serial
>> SCSI:  Target spinup took 0 ms.
>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
>> flags: ncq stag pm led clo only pmp pio slum part ccc apst
>> Net:   eth0: ethernet@01c0b000
>> starting USB...
>> USB0:   USB EHCI 1.00
>> USB1:   USB OHCI 1.0
>> USB2:   USB EHCI 1.00
>> USB3:   USB OHCI 1.0
>> scanning bus 0 for devices... 2 USB Device(s) found
>> scanning bus 2 for devices... 1 USB Device(s) found
>> scanning bus 1 for devices... 1 USB Device(s) found
>> scanning bus 3 for devices... 2 USB Device(s) found
>>        scanning usb for storage devices... 0 Storage Device(s) found
>> Hit any key to stop autoboot:  0
>> switch to partitions #0, OK
>> mmc0 is current device
>> Scanning mmc 0:1...
>> Found EFI removable media binary efi/boot/bootarm.efi
>> reading efi/boot/bootarm.efi
>> 64684 bytes read in 41 ms (1.5 MiB/s)
>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> ## Starting EFI application at 42000000 ...
>> Scanning disks on scsi...
>> Scanning disks on usb...
>> Scanning disks on mmc...
>> MMC Device 1 not found
>> MMC Device 2 not found
>> MMC Device 3 not found
>> Found 6 disks
>>
>>> OpenBSD/armv7 BOOTARM 0.5
>>>>
>>> boot>
>> cannot open sd0a:/etc/random.seed: No such file or directory
>> booting sd0a:/bsd: 2151556+7983908+438824 [80+301248+143324]=0xa84fd4
>>
>> ...
>> sd0 at scsibus0 targ 0 lun 0: <ATA, TOSHIBA MQ01ABD1, AX00> SCSI3
>> 0/direct
>> fixed naa.5000039514a065a8
>> sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
>> ...
>> sd1 at scsibus1 targ 1 lun 0: <Sandisk, SA08G, 0021> SCSI2 0/direct
>> removable
>> sd1: 7420MB, 512 bytes/sector, 15196160 sectors
>> axe0 at uhub0 port 1 configuration 1 interface 0 "ASIX Electronics
>> AX88772B" rev 2.00/0.01 addr 2
>> axe0: AX88772B, address 00:00:00:00:00:01
>> ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1:
>> OUI
>> 0x000ec6, model 0x0008
>> boot device: sd0
>> root on rd0a swap on rd0b dump on rd0b
>> WARNING: preposterous clock chip time
>> WARNING: CHECK AND RESET THE DATE!
>> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>>
>> Welcome to the OpenBSD/armv7 6.1 installation program.
>> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? shell
>>

Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

Re: Olinuxino Allwinner A10 installation successful l, but boot again into yet another Installation ?

soko.tica
U-boot still sees your mmc card as the default boot device. Try (in U-boot
prompt)

#setenv boot_targets usb0 mmc0 pxe dhcp
#saveenv
#printenv

On Sun, Apr 23, 2017 at 4:29 AM, Patrick YU <[hidden email]> wrote:

> Thanks Soko -- setting to default boot on the OpenBSD partition didn't
> help.
> Instead, I had to specify the root device manually to the boot loader
> using the -a flag.  Without such, I notice the root device is still
> pointing to the SD card ??
>
>> boot device: sd0
>>> root on rd0a swap on rd0b dump on rd0b
>>>
>>
> At the bootloader, I use the flag -a
> OpenBSD/armv7 BOOTARM 0.5
> boot> b sd0a:/bsd -a
> Then OpenBSD proposes the root device to be sd0a, for me to confirm.  How
> can I fix this ?
>
> Issue now is pfctl invocations in /etc/rc is triggering
> pfctl: /dev/pf: Device not configured --> does the device pf in
> /etc/MAKEDEV require a different numbers for the my A10 device ??
>
> The /etc/rc boot-up continued with failed start-up of daemons:
>    starting early daemons: syslogd(failed) pflogd(failed).
>    starting RPC daemons:.
>    savecore: can't find device 20/14778624
>    checking quotas: done.
>    kvm_mkdb: can't open /dev/ksyms
>    clearing /tmp
>    kern.securelevel: 0 -> 1
>    creating runtime link editor directory cache.
>    preserving editor files.
>    starting network daemons: sshd(failed) smtpd(failed) sndiod(failed).
>    ifconfig: SIOCSIFGATTR: No such file or directory
>    starting local daemons: cron(failed).
>
> I had to commented-out  ntpd to let the boot-up arriving at the login:
> prompt !!
>
> Any advice / comment is appreciated !
>
> -- Patrick
> On 2017-04-21 09:22, soko.tica wrote:
>
>> There is a Linux files partition on your sd0 that is marked bootable. It
>> shouldn't be there. FAT32L should, I believe, be marked bootable.
>>
>> You probably haven't cleared up the disk before the installation properly.
>> Clear it by fdisk, mark all partitions blank (zero) and repeat the
>> installation.
>>
>> On Thu, Apr 20, 2017 at 5:26 AM, Patrick YU <patrickyu> wrote:
>>
>> After successfully installing on an Olinuxino A10 board via the SD card
>>> onto a Toshiba disk with the following MBR partition table, I rebooted
>>> and
>>> again offered to perform another OpenBSD installation.  Why ?  Thanks in
>>> advance for any enlightenment !
>>>
>>> -- Patrick
>>>
>>> # fdisk sd0
>>> Disk: sd0       geometry: 121601/255/63 [1953525168 Sectors]
>>> Offset: 0       Signature: 0xAA55
>>>             Starting         Ending         LBA Info:
>>>  #: id      C   H   S -      C   H   S [       start:        size ]
>>> ------------------------------------------------------------
>>> -------------------
>>>  0: 83      0  32  33 -  58743 224 41 [        2048:   943718400 ] Linux
>>> files*
>>>  1: 0C  58743 224 42 -  58746 109 51 [   943720448:       40960 ] FAT32L
>>>  2: A6  58746 109  52 - 118795 153  14 [   943761408:   964689920 ]
>>> OpenBSD
>>>  3: 00      0   0   0 -      0   0   0 [           0:           0 ]
>>> unused
>>>
>>> U-Boot 2017.03 (Apr 03 2017 - 11:14:00 -0600) Allwinner Technology
>>>
>>> CPU:   Allwinner A10 (SUN4I)
>>> Model: Olimex A10-OLinuXino-LIME
>>> I2C:   ready
>>> DRAM:  512 MiB
>>> MMC:   SUNXI SD/MMC: 0
>>> *** Warning - bad CRC, using default environment
>>>
>>> In:    serial
>>> Out:   serial
>>> Err:   serial
>>> SCSI:  Target spinup took 0 ms.
>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst
>>> Net:   eth0: ethernet@01c0b000
>>> starting USB...
>>> USB0:   USB EHCI 1.00
>>> USB1:   USB OHCI 1.0
>>> USB2:   USB EHCI 1.00
>>> USB3:   USB OHCI 1.0
>>> scanning bus 0 for devices... 2 USB Device(s) found
>>> scanning bus 2 for devices... 1 USB Device(s) found
>>> scanning bus 1 for devices... 1 USB Device(s) found
>>> scanning bus 3 for devices... 2 USB Device(s) found
>>>        scanning usb for storage devices... 0 Storage Device(s) found
>>> Hit any key to stop autoboot:  0
>>> switch to partitions #0, OK
>>> mmc0 is current device
>>> Scanning mmc 0:1...
>>> Found EFI removable media binary efi/boot/bootarm.efi
>>> reading efi/boot/bootarm.efi
>>> 64684 bytes read in 41 ms (1.5 MiB/s)
>>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>>> ## Starting EFI application at 42000000 ...
>>> Scanning disks on scsi...
>>> Scanning disks on usb...
>>> Scanning disks on mmc...
>>> MMC Device 1 not found
>>> MMC Device 2 not found
>>> MMC Device 3 not found
>>> Found 6 disks
>>>
>>> OpenBSD/armv7 BOOTARM 0.5
>>>>
>>>>>
>>>>> boot>
>>>>
>>> cannot open sd0a:/etc/random.seed: No such file or directory
>>> booting sd0a:/bsd: 2151556+7983908+438824 [80+301248+143324]=0xa84fd4
>>>
>>> ...
>>> sd0 at scsibus0 targ 0 lun 0: <ATA, TOSHIBA MQ01ABD1, AX00> SCSI3
>>> 0/direct
>>> fixed naa.5000039514a065a8
>>> sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
>>> ...
>>> sd1 at scsibus1 targ 1 lun 0: <Sandisk, SA08G, 0021> SCSI2 0/direct
>>> removable
>>> sd1: 7420MB, 512 bytes/sector, 15196160 sectors
>>> axe0 at uhub0 port 1 configuration 1 interface 0 "ASIX Electronics
>>> AX88772B" rev 2.00/0.01 addr 2
>>> axe0: AX88772B, address 00:00:00:00:00:01
>>> ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
>>> 0x000ec6, model 0x0008
>>> boot device: sd0
>>> root on rd0a swap on rd0b dump on rd0b
>>> WARNING: preposterous clock chip time
>>> WARNING: CHECK AND RESET THE DATE!
>>> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>>>
>>> Welcome to the OpenBSD/armv7 6.1 installation program.
>>> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? shell
>>>
>>>
Loading...