Netgear WG111.

classic Classic list List threaded Threaded
8 messages Options
Reply | Threaded
Open this post in threaded view
|

Netgear WG111.

David Walker-16
Hey kids.

I'm running a snapshot from a week or so ago:
OpenBSD 5.0 GENERIC#39

I have a Netgear WG111 v2 USB wifi adapter that might be supported
according to urtw(4) but only gets ugen status.
I haven't used this thing for a long time and can't remember previous status.

Is there any procedure I need to do or should I assume it's unsupported?

Best wishes.

OpenBSD 5.0 (GENERIC) #39: Mon Aug  8 14:53:43 MDT 2011
   [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 731 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,SER,MMX,FXSR,SSE
real mem  = 266858496 (254MB)
avail mem = 252444672 (240MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/05/01, BIOS32 rev. 0 @
0xfd87d, SMBIOS rev. 2.2 @ 0xe4010 (42 entries)
bios0: vendor Phoenix Technologies Ltd. version "IP.01.08US" date 12/05/2001
bios0: Hewlett-Packard HP Vectra
apm0 at bios0: Power Management spec V1.2
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xfd810/0x7f0
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf30/176 (9 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xa000 0xe0000/0x4000! 0xe4000/0xc000!
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82815 Host" rev 0x02
vga1 at pci0 dev 2 function 0 "Intel 82815 Video" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0xf0000000, size 0x4000000
ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02
pci1 at ppb0 bus 1
xl0 at pci1 dev 4 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 7,
address 00:01:03:03:c3:8c
bmtphy0 at xl0 phy 24: 3C905C internal PHY, rev. 7
ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02:
24-bit timer at 3579545Hz
pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <WDC WD80EB-28CGH2>
wd0: 16-sector PIO, LBA, 7633MB, 15633072 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <ATAPI-CD, ROM-DRIVE-52MAX, 52E4> ATAPI
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 11
ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 9
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 128MB SDRAM non-parity PC133CL2
spdmem1 at iic0 addr 0x51: 128MB SDRAM non-parity PC133CL2
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4: polled
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
mtrr: Pentium Pro MTRR support
ugen0 at uhub0 port 1 "GlobespanVirata NETGEAR WG111" rev 2.00/10.20 addr 2
uhub1 at uhub0 port 2 "ALCOR Generic USB Hub" rev 1.10/3.12 addr 3
uhidev0 at uhub1 port 2 configuration 1 interface 0 "Microsoft
Microsoft Basic Optical Mouse v2.0" rev 1.10/1.99 addr 4
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
uhidev1 at uhub1 port 4 configuration 1 interface 0 "NOVATEK USB
Keyboard" rev 1.10/1.12 addr 5
uhidev1: iclass 3/1
ukbd0 at uhidev1: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev2 at uhub1 port 4 configuration 1 interface 1 "NOVATEK USB
Keyboard" rev 1.10/1.12 addr 5
uhidev2: iclass 3/0, 4 report ids
uhid0 at uhidev2 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev2 reportid 3: input=3, output=0, feature=0
uhid2 at uhidev2 reportid 4: input=2, output=0, feature=0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0a (01f39c01585cc992.a) swap on wd0b dump on wd0b
wsdisplay0: screen 6 added (80x25, vt100 emulation)
wsdisplay0: screen 7 added (80x25, vt100 emulation)
wsdisplay0: screen 8 added (80x25, vt100 emulation)
wsdisplay0: screen 9 added (80x25, vt100 emulation)
wsdisplay0: screen 10 added (80x25, vt100 emulation)
wsdisplay0: screen 11 added (80x25, vt100 emulation)
wsmouse0 detached
ums0 detached
uhidev0 detached
wskbd1: disconnecting from wsdisplay0
wskbd1 detached
ukbd0 detached
uhidev1 detached
uhid0 detached
uhid1 detached
uhid2 detached
uhidev2 detached
uhub1 detached
uhub1 at uhub0 port 2 "ALCOR Generic USB Hub" rev 1.10/3.12 addr 3
uhidev0 at uhub1 port 2 configuration 1 interface 0 "Microsoft
Microsoft Basic Optical Mouse v2.0" rev 1.10/1.99 addr 4
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
uhidev1 at uhub1 port 4 configuration 1 interface 0 "NOVATEK USB
Keyboard" rev 1.10/1.12 addr 5
uhidev1: iclass 3/1
ukbd0 at uhidev1: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev2 at uhub1 port 4 configuration 1 interface 1 "NOVATEK USB
Keyboard" rev 1.10/1.12 addr 5
uhidev2: iclass 3/0, 4 report ids
uhid0 at uhidev2 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev2 reportid 3: input=3, output=0, feature=0
uhid2 at uhidev2 reportid 4: input=2, output=0, feature=0

Reply | Threaded
Open this post in threaded view
|

Re: Netgear WG111.

Tomas Bodzar-4
Hi,

post output of 'usbdevs -v' command. Install usbutil package as well
and post output of 'usbctl -a 2 -f /dev/usb0'


$ pkg_info usbutil
Information for inst:usbutil-0.5p0

Comment:
USB developer utilities

Description:
USB developer utilities:

usbctl
        Dump information about devices on a USB bus.
usbdebug
        Set the kernel debugging flag.
usbgen
        Dump descriptors of a generic device.
        usbgen -f ugenN -v -D
usbstats
        Gives statistics for a USB host controller.

Maintainer: The OpenBSD ports mailing-list <[hidden email]>


$

On Sat, Aug 20, 2011 at 5:19 PM, David Walker <[hidden email]>
wrote:
> Hey kids.
>
> I'm running a snapshot from a week or so ago:
> OpenBSD 5.0 GENERIC#39
>
> I have a Netgear WG111 v2 USB wifi adapter that might be supported
> according to urtw(4) but only gets ugen status.
> I haven't used this thing for a long time and can't remember previous
status.
>
> Is there any procedure I need to do or should I assume it's unsupported?
>
> Best wishes.
>
> OpenBSD 5.0 (GENERIC) #39: Mon Aug B 8 14:53:43 MDT 2011
> B  [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel Pentium III ("GenuineIntel" 686-class) 731 MHz
> cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,SER,MMX,FXSR,S
SE
> real mem B = 266858496 (254MB)
> avail mem = 252444672 (240MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 12/05/01, BIOS32 rev. 0 @
> 0xfd87d, SMBIOS rev. 2.2 @ 0xe4010 (42 entries)
> bios0: vendor Phoenix Technologies Ltd. version "IP.01.08US" date
12/05/2001

> bios0: Hewlett-Packard HP Vectra
> apm0 at bios0: Power Management spec V1.2
> acpi at bios0 function 0x0 not configured
> pcibios0 at bios0: rev 2.1 @ 0xfd810/0x7f0
> pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf30/176 (9 entries)
> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
> pcibios0: PCI bus #1 is the last bus
> bios0: ROM list: 0xc0000/0xa000 0xe0000/0x4000! 0xe4000/0xc000!
> cpu0 at mainbus0: (uniprocessor)
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82815 Host" rev 0x02
> vga1 at pci0 dev 2 function 0 "Intel 82815 Video" rev 0x02
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> intagp0 at vga1
> agp0 at intagp0: aperture at 0xf0000000, size 0x4000000
> ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02
> pci1 at ppb0 bus 1
> xl0 at pci1 dev 4 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 7,
> address 00:01:03:03:c3:8c
> bmtphy0 at xl0 phy 24: 3C905C internal PHY, rev. 7
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02:
> 24-bit timer at 3579545Hz
> pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA,
> channel 0 wired to compatibility, channel 1 wired to compatibility
> wd0 at pciide0 channel 0 drive 0: <WDC WD80EB-28CGH2>
> wd0: 16-sector PIO, LBA, 7633MB, 15633072 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> atapiscsi0 at pciide0 channel 1 drive 0
> scsibus0 at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: <ATAPI-CD, ROM-DRIVE-52MAX, 52E4> ATAPI
> 5/cdrom removable
> cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 11
> ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 9
> iic0 at ichiic0
> spdmem0 at iic0 addr 0x50: 128MB SDRAM non-parity PC133CL2
> spdmem1 at iic0 addr 0x51: 128MB SDRAM non-parity PC133CL2
> isa0 at ichpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> lpt0 at isa0 port 0x378/4: polled
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> usb0 at uhci0: USB revision 1.0
> uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> mtrr: Pentium Pro MTRR support
> ugen0 at uhub0 port 1 "GlobespanVirata NETGEAR WG111" rev 2.00/10.20 addr 2
> uhub1 at uhub0 port 2 "ALCOR Generic USB Hub" rev 1.10/3.12 addr 3
> uhidev0 at uhub1 port 2 configuration 1 interface 0 "Microsoft
> Microsoft Basic Optical Mouse v2.0" rev 1.10/1.99 addr 4
> uhidev0: iclass 3/1
> ums0 at uhidev0: 3 buttons, Z dir
> wsmouse0 at ums0 mux 0
> uhidev1 at uhub1 port 4 configuration 1 interface 0 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev1: iclass 3/1
> ukbd0 at uhidev1: 8 modifier keys, 6 key codes
> wskbd1 at ukbd0 mux 1
> wskbd1: connecting to wsdisplay0
> uhidev2 at uhub1 port 4 configuration 1 interface 1 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev2: iclass 3/0, 4 report ids
> uhid0 at uhidev2 reportid 2: input=1, output=0, feature=0
> uhid1 at uhidev2 reportid 3: input=3, output=0, feature=0
> uhid2 at uhidev2 reportid 4: input=2, output=0, feature=0
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on wd0a (01f39c01585cc992.a) swap on wd0b dump on wd0b
> wsdisplay0: screen 6 added (80x25, vt100 emulation)
> wsdisplay0: screen 7 added (80x25, vt100 emulation)
> wsdisplay0: screen 8 added (80x25, vt100 emulation)
> wsdisplay0: screen 9 added (80x25, vt100 emulation)
> wsdisplay0: screen 10 added (80x25, vt100 emulation)
> wsdisplay0: screen 11 added (80x25, vt100 emulation)
> wsmouse0 detached
> ums0 detached
> uhidev0 detached
> wskbd1: disconnecting from wsdisplay0
> wskbd1 detached
> ukbd0 detached
> uhidev1 detached
> uhid0 detached
> uhid1 detached
> uhid2 detached
> uhidev2 detached
> uhub1 detached
> uhub1 at uhub0 port 2 "ALCOR Generic USB Hub" rev 1.10/3.12 addr 3
> uhidev0 at uhub1 port 2 configuration 1 interface 0 "Microsoft
> Microsoft Basic Optical Mouse v2.0" rev 1.10/1.99 addr 4
> uhidev0: iclass 3/1
> ums0 at uhidev0: 3 buttons, Z dir
> wsmouse0 at ums0 mux 0
> uhidev1 at uhub1 port 4 configuration 1 interface 0 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev1: iclass 3/1
> ukbd0 at uhidev1: 8 modifier keys, 6 key codes
> wskbd1 at ukbd0 mux 1
> wskbd1: connecting to wsdisplay0
> uhidev2 at uhub1 port 4 configuration 1 interface 1 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev2: iclass 3/0, 4 report ids
> uhid0 at uhidev2 reportid 2: input=1, output=0, feature=0
> uhid1 at uhidev2 reportid 3: input=3, output=0, feature=0
> uhid2 at uhidev2 reportid 4: input=2, output=0, feature=0

Reply | Threaded
Open this post in threaded view
|

Re: Netgear WG111.

David Walker-16
Hi Thomas.
Sorry for the delay.

On 21/08/2011, Tomas Bodzar <[hidden email]> wrote:
> Hi,
>
> post output of 'usbdevs -v' command.

Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
 port 1 addr 2: full speed, power 500 mA, config 1, NETGEAR
WG111(0x4240), GlobespanVirata(0x0846), rev 10.20, iSerialNumber
3887-0000
 port 2 addr 3: full speed, self powered, config 1, Generic USB
Hub(0x9254), ALCOR(0x058f), rev 3.12
  port 1 powered
  port 2 addr 4: low speed, power 100 mA, config 1, Microsoft Basic
Optical Mouse v2.0(0x00cb), Microsoft(0x045e), rev 1.99
  port 3 powered
  port 4 addr 5: low speed, power 100 mA, config 1, USB
Keyboard(0x00f2), NOVATEK(0x0603), rev 1.12

> Install usbutil package as well
> and post output of 'usbctl -a 2 -f /dev/usb0'

DEVICE addr 2
DEVICE descriptor:
bLength=18 bDescriptorType=device(1) bcdUSB=2.00 bDeviceClass=0
bDeviceSubClass=0
bDeviceProtocol=0 bMaxPacketSize=64 idVendor=0x0846 idProduct=0x4240
bcdDevice=1020
iManufacturer=1(GlobespanVirata) iProduct=2(NETGEAR WG111)
iSerialNumber=3(3887-0000) bNumConfigurations=1

CONFIGURATION descriptor 0:
bLength=9 bDescriptorType=config(2) wTotalLength=53 bNumInterface=1
bConfigurationValue=1 iConfiguration=0() bmAttributes=80 bMaxPower=500 mA

INTERFACE descriptor 0:
bLength=9 bDescriptorType=interface(4) bInterfaceNumber=0 bAlternateSetting=0
bNumEndpoints=5 bInterfaceClass=255 bInterfaceSubClass=255
bInterfaceProtocol=255 iInterface=0()

ENDPOINT descriptor:
bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=1-in
bmAttributes=bulk wMaxPacketSize=64 bInterval=0

ENDPOINT descriptor:
bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=1-out
bmAttributes=bulk wMaxPacketSize=64 bInterval=0

ENDPOINT descriptor:
bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=2-in
bmAttributes=bulk wMaxPacketSize=64 bInterval=0

ENDPOINT descriptor:
bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=2-out
bmAttributes=bulk wMaxPacketSize=64 bInterval=0

ENDPOINT descriptor:
bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=3-in
bmAttributes=interrupt wMaxPacketSize=64 bInterval=1

current configuration 1

----------

I noticed this:

MASTER_SITES= ftp://ftp.augustsson.net/pub/netbsd/

http://www.openbsd.org/cgi-bin/cvsweb/ports/sysutils/usbutil/Makefile?rev=1.19;content-type=text%2Fplain

AFAICT, there's nothing useful there.
I see this:
http://www.freshports.org/sysutils/usbutil/

Best wishes.

Reply | Threaded
Open this post in threaded view
|

Re: Netgear WG111.

Tomas Bodzar-4
On Thu, Sep 8, 2011 at 5:53 AM, David Walker <[hidden email]>
wrote:

> Hi Thomas.
> Sorry for the delay.
>
> On 21/08/2011, Tomas Bodzar <[hidden email]> wrote:
>> Hi,
>>
>> post output of 'usbdevs -v' command.
>
> Controller /dev/usb0:
> addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
> Intel(0x8086), rev 1.00
> B port 1 addr 2: full speed, power 500 mA, config 1, NETGEAR
> WG111(0x4240), GlobespanVirata(0x0846), rev 10.20, iSerialNumber
> 3887-0000
> B port 2 addr 3: full speed, self powered, config 1, Generic USB
> Hub(0x9254), ALCOR(0x058f), rev 3.12
> B port 1 powered
> B port 2 addr 4: low speed, power 100 mA, config 1, Microsoft Basic
> Optical Mouse v2.0(0x00cb), Microsoft(0x045e), rev 1.99
> B port 3 powered
> B port 4 addr 5: low speed, power 100 mA, config 1, USB
> Keyboard(0x00f2), NOVATEK(0x0603), rev 1.12
>
>> Install usbutil package as well
>> and post output of 'usbctl -a 2 -f /dev/usb0'
>
> DEVICE addr 2
> DEVICE descriptor:
> bLength=18 bDescriptorType=device(1) bcdUSB=2.00 bDeviceClass=0
> bDeviceSubClass=0
> bDeviceProtocol=0 bMaxPacketSize=64 idVendor=0x0846 idProduct=0x4240
> bcdDevice=1020
> iManufacturer=1(GlobespanVirata) iProduct=2(NETGEAR WG111)
> iSerialNumber=3(3887-0000) bNumConfigurations=1
>
> CONFIGURATION descriptor 0:
> bLength=9 bDescriptorType=config(2) wTotalLength=53 bNumInterface=1
> bConfigurationValue=1 iConfiguration=0() bmAttributes=80 bMaxPower=500 mA
>
> INTERFACE descriptor 0:
> bLength=9 bDescriptorType=interface(4) bInterfaceNumber=0
bAlternateSetting=0

> bNumEndpoints=5 bInterfaceClass=255 bInterfaceSubClass=255
> bInterfaceProtocol=255 iInterface=0()
>
> ENDPOINT descriptor:
> bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=1-in
> bmAttributes=bulk wMaxPacketSize=64 bInterval=0
>
> ENDPOINT descriptor:
> bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=1-out
> bmAttributes=bulk wMaxPacketSize=64 bInterval=0
>
> ENDPOINT descriptor:
> bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=2-in
> bmAttributes=bulk wMaxPacketSize=64 bInterval=0
>
> ENDPOINT descriptor:
> bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=2-out
> bmAttributes=bulk wMaxPacketSize=64 bInterval=0
>
> ENDPOINT descriptor:
> bLength=7 bDescriptorType=endpoint(5) bEndpointAddress=3-in
> bmAttributes=interrupt wMaxPacketSize=64 bInterval=1
>
> current configuration 1

Do you have latest snapshot to see if something changed in dmesg output?

>
> ----------
>
> I noticed this:
>
> MASTER_SITES= B  ftp://ftp.augustsson.net/pub/netbsd/
>
>
http://www.openbsd.org/cgi-bin/cvsweb/ports/sysutils/usbutil/Makefile?rev=1.1
9;content-type=text%2Fplain
>
> AFAICT, there's nothing useful there.
> I see this:
> http://www.freshports.org/sysutils/usbutil/

Not sure how are fbsd ports related to obsd. This site is correct
http://openports.se/sysutils/usbutil

>
> Best wishes.

Reply | Threaded
Open this post in threaded view
|

Re: Netgear WG111.

Tomas Bodzar-4
In reply to this post by David Walker-16
On Sat, Aug 20, 2011 at 5:19 PM, David Walker <[hidden email]>
wrote:
> Hey kids.
>
> I'm running a snapshot from a week or so ago:
> OpenBSD 5.0 GENERIC#39
>
> I have a Netgear WG111 v2 USB wifi adapter that might be supported
> according to urtw(4) but only gets ugen status.
> I haven't used this thing for a long time and can't remember previous
status.
>
> Is there any procedure I need to do or should I assume it's unsupported?
>
> Best wishes.
>
> OpenBSD 5.0 (GENERIC) #39: Mon Aug B 8 14:53:43 MDT 2011
> B  [hidden email]:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel Pentium III ("GenuineIntel" 686-class) 731 MHz
> cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,SER,MMX,FXSR,S
SE
> real mem B = 266858496 (254MB)
> avail mem = 252444672 (240MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 12/05/01, BIOS32 rev. 0 @
> 0xfd87d, SMBIOS rev. 2.2 @ 0xe4010 (42 entries)
> bios0: vendor Phoenix Technologies Ltd. version "IP.01.08US" date
12/05/2001
> bios0: Hewlett-Packard HP Vectra
> apm0 at bios0: Power Management spec V1.2
> acpi at bios0 function 0x0 not configured

Do you have latest BIOS available for that machine? Did you disable acpi?

> pcibios0 at bios0: rev 2.1 @ 0xfd810/0x7f0
> pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf30/176 (9 entries)
> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
> pcibios0: PCI bus #1 is the last bus
> bios0: ROM list: 0xc0000/0xa000 0xe0000/0x4000! 0xe4000/0xc000!
> cpu0 at mainbus0: (uniprocessor)
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82815 Host" rev 0x02
> vga1 at pci0 dev 2 function 0 "Intel 82815 Video" rev 0x02
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> intagp0 at vga1
> agp0 at intagp0: aperture at 0xf0000000, size 0x4000000
> ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02
> pci1 at ppb0 bus 1
> xl0 at pci1 dev 4 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 7,
> address 00:01:03:03:c3:8c
> bmtphy0 at xl0 phy 24: 3C905C internal PHY, rev. 7
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02:
> 24-bit timer at 3579545Hz
> pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA,
> channel 0 wired to compatibility, channel 1 wired to compatibility
> wd0 at pciide0 channel 0 drive 0: <WDC WD80EB-28CGH2>
> wd0: 16-sector PIO, LBA, 7633MB, 15633072 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> atapiscsi0 at pciide0 channel 1 drive 0
> scsibus0 at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: <ATAPI-CD, ROM-DRIVE-52MAX, 52E4> ATAPI
> 5/cdrom removable
> cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 11
> ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 9
> iic0 at ichiic0
> spdmem0 at iic0 addr 0x50: 128MB SDRAM non-parity PC133CL2
> spdmem1 at iic0 addr 0x51: 128MB SDRAM non-parity PC133CL2
> isa0 at ichpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> lpt0 at isa0 port 0x378/4: polled
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> usb0 at uhci0: USB revision 1.0
> uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> mtrr: Pentium Pro MTRR support
> ugen0 at uhub0 port 1 "GlobespanVirata NETGEAR WG111" rev 2.00/10.20 addr 2

Maybe that device needs USB 2.0 as in docs they say that v2/v3 (which
are only supported by OpenBSD) needs USB 2.0

> uhub1 at uhub0 port 2 "ALCOR Generic USB Hub" rev 1.10/3.12 addr 3
> uhidev0 at uhub1 port 2 configuration 1 interface 0 "Microsoft
> Microsoft Basic Optical Mouse v2.0" rev 1.10/1.99 addr 4
> uhidev0: iclass 3/1
> ums0 at uhidev0: 3 buttons, Z dir
> wsmouse0 at ums0 mux 0
> uhidev1 at uhub1 port 4 configuration 1 interface 0 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev1: iclass 3/1
> ukbd0 at uhidev1: 8 modifier keys, 6 key codes
> wskbd1 at ukbd0 mux 1
> wskbd1: connecting to wsdisplay0
> uhidev2 at uhub1 port 4 configuration 1 interface 1 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev2: iclass 3/0, 4 report ids
> uhid0 at uhidev2 reportid 2: input=1, output=0, feature=0
> uhid1 at uhidev2 reportid 3: input=3, output=0, feature=0
> uhid2 at uhidev2 reportid 4: input=2, output=0, feature=0
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on wd0a (01f39c01585cc992.a) swap on wd0b dump on wd0b
> wsdisplay0: screen 6 added (80x25, vt100 emulation)
> wsdisplay0: screen 7 added (80x25, vt100 emulation)
> wsdisplay0: screen 8 added (80x25, vt100 emulation)
> wsdisplay0: screen 9 added (80x25, vt100 emulation)
> wsdisplay0: screen 10 added (80x25, vt100 emulation)
> wsdisplay0: screen 11 added (80x25, vt100 emulation)
> wsmouse0 detached
> ums0 detached
> uhidev0 detached
> wskbd1: disconnecting from wsdisplay0
> wskbd1 detached
> ukbd0 detached
> uhidev1 detached
> uhid0 detached
> uhid1 detached
> uhid2 detached
> uhidev2 detached
> uhub1 detached
> uhub1 at uhub0 port 2 "ALCOR Generic USB Hub" rev 1.10/3.12 addr 3
> uhidev0 at uhub1 port 2 configuration 1 interface 0 "Microsoft
> Microsoft Basic Optical Mouse v2.0" rev 1.10/1.99 addr 4
> uhidev0: iclass 3/1
> ums0 at uhidev0: 3 buttons, Z dir
> wsmouse0 at ums0 mux 0
> uhidev1 at uhub1 port 4 configuration 1 interface 0 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev1: iclass 3/1
> ukbd0 at uhidev1: 8 modifier keys, 6 key codes
> wskbd1 at ukbd0 mux 1
> wskbd1: connecting to wsdisplay0
> uhidev2 at uhub1 port 4 configuration 1 interface 1 "NOVATEK USB
> Keyboard" rev 1.10/1.12 addr 5
> uhidev2: iclass 3/0, 4 report ids
> uhid0 at uhidev2 reportid 2: input=1, output=0, feature=0
> uhid1 at uhidev2 reportid 3: input=3, output=0, feature=0
> uhid2 at uhidev2 reportid 4: input=2, output=0, feature=0

Reply | Threaded
Open this post in threaded view
|

Re: Netgear WG111.

Jonathan Gray
In reply to this post by David Walker-16
On Thu, Sep 08, 2011 at 01:23:22PM +0930, David Walker wrote:

> Hi Thomas.
> Sorry for the delay.
>
> On 21/08/2011, Tomas Bodzar <[hidden email]> wrote:
> > Hi,
> >
> > post output of 'usbdevs -v' command.
>
> Controller /dev/usb0:
> addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
> Intel(0x8086), rev 1.00
>  port 1 addr 2: full speed, power 500 mA, config 1, NETGEAR
> WG111(0x4240), GlobespanVirata(0x0846), rev 10.20, iSerialNumber
> 3887-0000

This is not a urtw device (which is 0x6a00) but rather an old
style fullmac prism device which we don't support.  We
support the newer softmac usb prism (upgt) and the older 802.11
prism (wi@usb) but not that particular device.

Reply | Threaded
Open this post in threaded view
|

Re: Netgear WG111.

David Walker-16
On 08/09/2011, Jonathan Gray <[hidden email]> wrote:
> This is not a urtw device (which is 0x6a00) but rather an old
> style fullmac prism device which we don't support.  We
> support the newer softmac usb prism (upgt) and the older 802.11
> prism (wi@usb) but not that particular device.

Thank you Jonathon.

Best wishes.

Reply | Threaded
Open this post in threaded view
|

Re: Netgear WG111.

Anil Gulati
In reply to this post by Tomas Bodzar-4
FYI: You need the upgt driver. I have this device and it was supported in
FreeBSD 8.2 using upgt. I'm having problems in FreeBSD 9.0 at the moment but in
theory it is still supported, and in any case, it requires upgt.