Quantcast

It's dangerous to install OpenBSD 5.6 on SPARC Enterprise M3000

Previous Topic Next Topic
 
classic Classic list List threaded Threaded
1 message Options
Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

It's dangerous to install OpenBSD 5.6 on SPARC Enterprise M3000

Naruaki.Etomi
Hello!
Please forgive me my lousy English.

I was installed OpenBSD 5.6 on SPARC Enterprise M3000.

During installation:
The following message was displayed on the console.
Get/VeMar 29 01:06:17 sbcondb1 fmd: SOURCE: sde, REV: 1.16, CSN:
PX61035173  EVENT-ID: dfc125c9-b6d9-45ab-9f0c-5a9901b2c3d8 Refer to
http://www.fujitsu.com/sparcenterprise/msg/SCF-8003-HA for detailed
information.
and
Automatic power off.

I was reboot a system.

The following message was displayed on the console.
XSCF> poweron -a
DomainIDs to power on:00
Continue? [y|n] :y
00 :Not powering on :Poweron canceled due to missing component.

I think that SPARC Enterprise M3000 is broken and will have to be repaired.

Use with Caution!!

-------------------------------------------------------------------------------------
Last login: Fri Mar 13 23:26:49 on ttys000
macbook-black:~ naruaki$ cu -l /dev/tty.usbserial-FTXUYJS9
Connected.
............finish
    DDR Real size: 256 MB
    DDR: 224 MB

## Booting image at ff800000 ...
   Image Name:   XSCF kernel 01090003 2.6.11.12-s
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1457048 Bytes =  1.4 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ff980000 ...
   Image Name:   XSCF rootfs 01090003 ,2010/07/01
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    5463455 Bytes =  5.2 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Ramdisk to 0baca000, end 0bfffd9f ... OK
Linux version 2.6.11.12-sec (gcc version 3.4.4) #1 Thu Jul 1 17:02:37 JST 2010
new message buffer at 0f700000 size 1048576
log_buf_len: 1048576
mpc85xx_cds_setup_arch
Built 1 zonelists
Kernel command line: root=/dev/ram rw console=ttyS0,9600
init=/sbin/init_change_root panic=1 mem=224M
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fbe79000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 218752k available (2188k kernel code, 668k data, 316k init, 0k highmem)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Freeing initrd memory: 5335k freed
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
i2c-algo-cpm: CPM2 I2C algorithm module version 0.1 (Mar 22, 2005)
FCC ENET Version 0.3
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
ip_tables: (C) 2000-2002 Netfilter core team
arp_tables: (C) 2002 David S. Miller
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 316k init
switching initrd filesystem, ramdisk to tmpfs
SCF Linux Boot Script 2006/03/04 for ROM boot environment
fsl-sec2 hardware crypt accelerator model3a ver 0.02 enabled

XSCF initial process start (pid=106)

load /scf/modules/lites_ldrv.ko  --  complete
load /scf/modules/drvscftrace.ko  --  complete
load /scf/modules/sec2_rsa.ko  --  complete
load /scf/modules/sec2_md5.ko  --  complete
load /scf/modules/sec2_des.ko  --  complete
load /scf/modules/sec2_arc4.ko  --  complete
load /scf/modules/sec2_aes.ko  --  complete
load /scf/modules/sec2_sha256.ko  --  complete
load /scf/modules/sec2_sha1.ko  --  complete
load /scf/modules/hw_random.ko  --  complete
load /scf/modules/scsi_mod.ko  --  complete
load /scf/modules/sd_mod.ko  --  complete
load /scf/modules/usbcore.ko  --  complete
load /scf/modules/ohci-hcd.ko  --  complete
load /scf/modules/usb-storage.ko  --  complete
load /scf/modules/drvbootfmem.ko  --  complete
load /scf/modules/drvmbc.ko  --  complete
load /scf/modules/drvnand.ko  --  complete
load /scf/modules/drvffc.ko  --  complete
load /scf/modules/drvffcint.ko  --  complete
load /scf/modules/drvrtc.ko  --  complete
load /scf/modules/drvxscfuart.ko  --  complete
load /scf/modules/drvrci.ko  --  complete
load /scf/modules/drvtimer.ko  --  complete
load /scf/modules/drvsdic.ko  --  complete
load /scf/modules/sm2s.ko  --  complete
load /scf/modules/spkmdrv.ko  --  complete
mount /dev/mtdblock0 -> /hcp0/linux  --  complete
mount /dev/mtdblock1 -> /hcp0/scfprog  --  complete
mount /dev/mtdblock2 -> /hcp0/gendata  --  complete
mount /dev/mtdblock3 -> /hcp0/remcscm  --  complete
mount /dev/mtdblock4 -> /hcpcommon/setup  --  complete
mount /dev/mtdblock5 -> /hcpcommon/obp  --  complete
mount /dev/mtdblock6 -> /hcpcommon/tmp  --  complete
mount /dev/mtdblock11 -> /hcpcommon/var  --  complete
mount /dev/mtdblock12 -> /hcpcommon/scflog1  --  complete
mount /dev/mtdblock13 -> /hcpcommon/scflog2  --  complete
execute S00mtab  --  complete
execute S00portmap  --  complete
execute S00tmpmake  --  complete
execute S00varclean  --  complete
execute S10ldconfig  --  complete
execute S15last_dmesg  --  complete
execute S20cfgcreate  --  complete
execute S50iptables  --  complete
execute S60check  --  complete
execute S61restore  --  complete
execute S99syslogd  --  complete
initialize XSCF common database (STANDALONE)  --  complete
start /scf/sbin/dbs (pid=336)
start /scf/sbin/ksyseventd (pid=337)
start /scf/sbin/syseventd (pid=342)
start /scf/init/scf_cmgrd (pid=350)
start /scf/init/scf_coremgr (pid=351)
start /scf/init/dualprocess (pid=352)
check SCF operation mode (for OPNL access)  --  complete
initialize OPNL  --  complete
check SCF operation mode  --  complete (ACTIVE)
start /scf/sbin/dbs (pid=371)
initialize XSCF common database (OWN)  --  complete
synchronize setup data (XSCF -> OPNL)  --  complete
initialize XSCF common database (ACTIVE)  --  complete
wait for database synchronization  --  complete
execute S00clis_all  --  complete
execute S10restore_ad  --  complete
execute S10restore_um  --  complete
execute S11network.sheth0: PHY is Intel LXT972A (1378e2)
  --  complete
execute S15ntpcheck.sh  --  complete
execute S21daemons  --  complete
execute S51scflog_SCFboot.sh  --  complete
execute S82cod  --  complete
execute S98bui  --  complete
execute S00clis_active  --  complete
execute S00cmem_check  --  complete
execute S00tmp_login  --  complete
execute S18restorefmdlog  --  complete
execute S19setfmurl  --  complete
execute S29setfmconf  --  complete
execute S50setupSCFboot.sh  --  complete
execute S83setservicetagdata  --  complete
start /scf/sbin/scf_panelmgr (pid=801)
start /scf/sbin/fmdsyncd (pid=802)
start /scf/sbin/auditd (pid=804)
start /scf/sbin/cmd (pid=805)
start /scf/sbin/cmd_sub (pid=806)
start /scf/sbin/errhandd (pid=807)
start /scf/sbin/fjdrd (pid=808)
start /scf/sbin/frura (pid=809)
start /scf/sbin/mond (pid=810)
start /scf/sbin/mond (pid=811)
start /scf/sbin/powerd (pid=812)
start /scf/sbin/rci (pid=813)
start /scf/sbin/rci_dual (pid=814)
start /scf/sbin/reset (pid=815)
start /scf/sbin/resetra (pid=816)
start /scf/sbin/rsyncprocess (pid=817)
start /scf/sbin/scf_firmup_exed (pid=818)
start /scf/sbin/scf_hardlog (pid=819)
start /scf/sbin/scf_loganalyze (pid=820)
start /scf/sbin/scf_procmeas (pid=821)
start /scf/sbin/sequence (pid=822)
start /scf/sbin/ttyd (pid=823)
start /scf/sbin/rm_eventd (pid=824)
start /scf/sbin/rm_queued (pid=825)
start /scf/sbin/apcsd (pid=826)
start /scf/sbin/codd (pid=827)
start /scf/sbin/scf_firmup_ctld (pid=828)
start /scf/sbin/fmd (pid=829)
start /scf/sbin/dscpd (pid=1013)
start /scf/sbin/monitor_msg (pid=1014)
start /scf/sbin/picld (pid=1015)
start /scf/sbin/sunmcrund (pid=1016)
start /scf/sbin/dfrud (pid=1017)
start /scf/sbin/iomgrd (pid=1018)
start /scf/sbin/archd (pid=1050)
wait for SCF_READY  --  complete
execute S20setupSCFready.sh  --  complete
execute S99rcclear  --  complete
execute S10iobox_scan  --  complete
execute S10restore_ad  --  complete
execute S10restore_um  --  complete
execute S84snmpd  --  complete
execute S85sunmc_esd  --  complete
execute S86limits  --  complete
execute S87opnl  --  complete
execute S99dr_recover.sh  --  complete
XSCF Initialize complete.

Mar 29 00:44:56 sbcondb1 XSCF[106]: XSCF Initialize complete.

login: default
Change the panel mode switch to Locked and press return...
Leave it in that position for at least 5 seconds.  Change the panel
mode switch to Service, and press return...
XSCF> poweron -a
DomainIDs to power on:00
Continue? [y|n] :y
00 :Powering on

*Note*
 This command only issues the instruction to power-on.
 The result of the instruction can be checked by the "showlogs power".
XSCF> console -d 0
Connect to DomainID 0?[y|n] :y
POST Sequence 01 CPU Check
POST Sequence 02 Banner
LSB#00 (XSB#00-0): POST 2.13.0 (2010/02/17 10:36)
POST Sequence 03 Fatal Check
POST Sequence 04 CPU Register
POST Sequence 05 STICK
POST Sequence 06 MMU
POST Sequence 07 Memory Initialize
POST Sequence 08 Memory
POST Sequence 09 Raw UE In Cache
POST Sequence 0A Floating Point Unit
POST Sequence 0B SC
POST Sequence 0C Cacheable Instruction
POST Sequence 0D Softint
POST Sequence 0E CPU Cross Call
POST Sequence 0F CMU-CH
POST Sequence 10 PCI-CH
POST Sequence 11 Master Device
POST Sequence 12 DSCP
POST Sequence 13 SC Check Before STICK Diag
POST Sequence 14 STICK Stop
POST Sequence 15 STICK Start
POST Sequence 16 Error CPU Check
POST Sequence 17 System Configuration
POST Sequence 18 System Status Check
POST Sequence 19 System Status Check After Sync
POST Sequence 1A OpenBoot Start...
POST Sequence Complete.

Fujitsu SPARC Enterprise M3000 Server, using Domain console
Copyright 2010 Sun Microsystems, Inc.  All rights reserved.
Copyright 2010 Sun Microsystems, Inc. and Fujitsu Limited. All rights reserved.
OpenBoot 4.24.14, 32768 MB memory installed, Serial #10042244.
Ethernet address 0:b:5d:e2:3b:84, Host ID: 80993b84.



Aborting auto-boot sequence.
{0} ok boot cdrom
Boot device: /pci@0,600000/pci@0/pci@0/scsi@0/disk@4,0:f  File and args:
OpenBSD IEEE 1275 Bootblock 1.3
..>> OpenBSD BOOT 1.6
Trying bsd...
open /pci@0,600000/pci@0/pci@0/scsi@0/disk@4,0:f/etc/random.seed: No
such file or directory
Booting /pci@0,600000/pci@0/pci@0/scsi@0/disk@4,0:f/bsd
3864176@0x1000000+2448@0x13af670+3261928@0x1800000+932376@0x1b1c5e8
symbols @ 0xfdaec300 119 start=0x1000000
console is /pseudo-console
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 5.6 (RAMDISK) #178: Fri Aug  8 05:00:27 MDT 2014
    [hidden email]:/usr/src/sys/arch/sparc64/compile/RAMDISK
real mem = 34359738368 (32768MB)
avail mem = 33803608064 (32237MB)
mainbus0 at root: Fujitsu SPARC Enterprise M3000 Server
cmp0 at mainbus0
core0 at cmp0
cpu0 at core0: FJSV,SPARC64-VII (rev 10.1) @ 2750 MHz
cpu0: physical 64K instruction (64 b/l), 64K data (64 b/l), 5120K
external (256 b/l)
"FJSV,SPARC64-VII" at core0 not configured
core1 at cmp0
"FJSV,SPARC64-VII" at core1 not configured
"FJSV,SPARC64-VII" at core1 not configured
"pseudo-mc" at mainbus0 not configured
psycho0 at mainbus0: pci10cf,138f, impl 0, version 4, ign 200
psycho0: bus range 0-0, PCI bus 0
pci0 at psycho0
ebus0 at pci0 dev 1 function 0 "Sun PCIO EBus2" rev 0x01
"flashprom" at ebus0 addr 0-3fffff not configured
com0 at ebus0 addr 400000-400007 ivec 0x2b: ns16550, no working fifo
com0: console
"scfc" at ebus0 addr 200000-20012f, 210000-210007, 300000-30ffff,
310000-31ffff, 320000-37ffff ivec 0x27 not configured
"panel" at ebus0 addr 280030-280030 ivec 0x25 not configured
pyro0 at mainbus0: "Oberon", rev 0, ign 0, bus A 2 to 255
pyro0: dvma map c0000000-ffffffff
pci1 at pyro0
ppb0 at pci1 dev 0 function 0 "PLX PEX 8533" rev 0xaa
pci2 at ppb0 bus 3
ppb1 at pci2 dev 0 function 0 "PLX PEX 8533" rev 0xaa
pci3 at ppb1 bus 4
mpi0 at pci3 dev 0 function 0 "Symbios Logic SAS1068E" rev 0x08: msi
mpi0: IKKAKU, firmware 1.29.5.0
scsibus0 at mpi0: 173 targets
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST973402SSUN72G, 0603> SCSI3
0/direct fixed naa.5000c5000c514d8b
sd0: 70007MB, 512 bytes/sector, 143374738 sectors
cd0 at scsibus0 targ 4 lun 0: <MATSHITA, DVD-RAM UJ875AS, 1.00> ATAPI
5/cdrom removable
ppb2 at pci2 dev 1 function 0 "PLX PEX 8533" rev 0xaa
pci4 at ppb2 bus 5
ppb3 at pci4 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xb5
pci5 at ppb3 bus 6
bge0 at pci5 dev 4 function 0 "Broadcom BCM5715" rev 0xa3, BCM5715 A3
(0x9003): ivec 0x15, address 00:0b:5d:e5:f6:0c
brgphy0 at bge0 phy 1: BCM5714 10/100/1000baseT/SX PHY, rev. 0
bge1 at pci5 dev 4 function 1 "Broadcom BCM5715" rev 0xa3, BCM5715 A3
(0x9003): ivec 0x16, address 00:0b:5d:e5:f6:0d
brgphy1 at bge1 phy 1: BCM5714 10/100/1000baseT/SX PHY, rev. 0
ppb4 at pci2 dev 2 function 0 "PLX PEX 8533" rev 0xaa
pci6 at ppb4 bus 7
ppb5 at pci6 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xb5
pci7 at ppb5 bus 8
bge2 at pci7 dev 4 function 0 "Broadcom BCM5715" rev 0xa3, BCM5715 A3
(0x9003): ivec 0x16, address 00:0b:5d:e5:f6:0e
brgphy2 at bge2 phy 1: BCM5714 10/100/1000baseT/SX PHY, rev. 0
bge3 at pci7 dev 4 function 1 "Broadcom BCM5715" rev 0xa3, BCM5715 A3
(0x9003): ivec 0x17, address 00:0b:5d:e5:f6:0f
brgphy3 at bge3 phy 1: BCM5714 10/100/1000baseT/SX PHY, rev. 0
ppb6 at pci2 dev 8 function 0 "PLX PEX 8533" rev 0xaa: msi
pci8 at ppb6 bus 9
pyro1 at mainbus0: "Oberon", rev 0, ign 40, bus B 2 to 255
pyro1: dvma map c0000000-ffffffff
pci9 at pyro1
ppb7 at pci9 dev 0 function 0 "PLX PEX 8533" rev 0xaa
pci10 at ppb7 bus 3
ppb8 at pci10 dev 0 function 0 "PLX PEX 8533" rev 0xaa: msi
pci11 at ppb8 bus 4
ppb9 at pci10 dev 8 function 0 "PLX PEX 8533" rev 0xaa: msi
pci12 at ppb9 bus 5
ppb10 at pci10 dev 9 function 0 "PLX PEX 8533" rev 0xaa: msi
pci13 at ppb10 bus 6
prtc0 at mainbus0
softraid0 at root
scsibus1 at softraid0: 256 targets
bootpath: /pci@0,600000/pci@0,0/pci@0,0/scsi@0,0/disk@4,0:f
root on rd0a swap on rd0b dump on rd0b
erase ^?, werase ^W, kill ^U, intr ^C, status ^T

Welcome to the OpenBSD/sparc64 5.6 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN.  You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.

Terminal type? [sun]
System hostname? (short form, e.g. 'foo') m3000

Available network interfaces are: bge0 bge1 bge2 bge3 vlan0.
Which network interface do you wish to configure? (or 'done') [bge0]
IPv4 address for bge0? (or 'dhcp' or 'none') [dhcp]
DHCPDISCOVER on bge0 - interval 1
DHCPOFFER from 192.168.1.1 (00:1b:8b:d8:df:bc)
DHCPREQUEST on bge0 to 255.255.255.255
DHCPACK from 192.168.1.1 (00:1b:8b:d8:df:bc)
bound to 192.168.1.7 -- renewal in 7200 seconds.
IPv6 address for bge0? (or 'rtsol' or 'none') [none]
Available network interfaces are: bge0 bge1 bge2 bge3 vlan0.
Which network interface do you wish to configure? (or 'done') [done]
Using DNS domainname my.domain
Using DNS nameservers at 192.168.1.1

Password for root account? (will not echo)
Password for root account? (again)
Start sshd(8) by default? [yes] yes
Start ntpd(8) by default? [no]
Setup a user? (enter a lower-case loginname, or 'no') [no] naruaki
Full name for user naruaki? [naruaki]
Password for user naruaki? (will not echo)
Password for user naruaki? (again)
Since you set up a user, disable sshd(8) logins to root? [yes] no
What timezone are you in? ('?' for list) [Asia/Tokyo]
Available disks are: sd0.
Which disk is the root disk? ('?' for details) [sd0]
Use DUIDs rather than device names in fstab? [yes]
The auto-allocated layout for sd0 is:
#                size           offset  fstype [fsize bsize  cpg]
  a:             5.0M        143369664  4.2BSD   2048 16384    1 # /
  c:         70007.2M                0  unused
  i:         70002.0M               63    NTFS
disklabel: this architecture requires partition 'a' to start at sector 0
disklabel: partition a: partition extends past end of unit
disklabel: warning, partition i: size % cylinder-size != 0
disklabel: warning, partition i: offset % cylinder-size != 0
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] A
disklabel: this architecture requires partition 'a' to start at sector 0
disklabel: partition a: partition extends past end of unit
disklabel: warning, partition i: size % cylinder-size != 0
disklabel: warning, partition i: offset % cylinder-size != 0
The auto-allocated layout for sd0 is:
#                size           offset  fstype [fsize bsize  cpg]
  a:             5.0M        143369664  4.2BSD   2048 16384    1 # /
  c:         70007.2M                0  unused
  i:         70002.0M               63    NTFS
disklabel: this architecture requires partition 'a' to start at sector 0
disklabel: partition a: partition extends past end of unit
disklabel: warning, partition i: size % cylinder-size != 0
disklabel: warning, partition i: offset % cylinder-size != 0
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a]
disklabel: this architecture requires partition 'a' to start at sector 0
disklabel: partition a: partition extends past end of unit
disklabel: warning, partition i: size % cylinder-size != 0
disklabel: warning, partition i: offset % cylinder-size != 0
The auto-allocated layout for sd0 is:
#                size           offset  fstype [fsize bsize  cpg]
  a:             5.0M        143369664  4.2BSD   2048 16384    1 # /
  c:         70007.2M                0  unused
  i:         70002.0M               63    NTFS
disklabel: this architecture requires partition 'a' to start at sector 0
disklabel: partition a: partition extends past end of unit
disklabel: warning, partition i: size % cylinder-size != 0
disklabel: warning, partition i: offset % cylinder-size != 0
...
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] c

You will now create a Sun-style disklabel on the disk.  The disklabel defines
how OpenBSD splits up the disk into OpenBSD partitions in which filesystems
and swap space are created.  You must provide each filesystem's mountpoint
in this program.

This platform requires that partition offsets/sizes be on cylinder boundaries.
Partition offsets/sizes will be rounded to the nearest cylinder automatically.
Label editor (enter '?' for help at any prompt)
> ?
Available commands:
 ? | h    - show help                 n [part] - set mount point
 A        - auto partition all space  p [unit] - print partitions
 a [part] - add partition             q        - quit & save changes
 b        - set OpenBSD boundaries    R [part] - resize auto allocated partition
 c [part] - change partition size     r        - display free space
 D        - reset label to default    s [path] - save label to file
 d [part] - delete partition          U        - undo all changes
 e        - edit drive parameters     u        - undo last change
 g [d|u]  - [d]isk or [u]ser geometry w        - write label to disk
 i        - modify disklabel UID      X        - toggle expert mode
 l [unit] - print disk label header   x        - exit & lose changes
 M        - disklabel(8) man page     z        - delete all partitions
 m [part] - modify partition

Suffixes can be used to indicate units other than sectors:
 'b' (bytes), 'k' (kilobytes), 'm' (megabytes), 'g' (gigabytes) 't' (terabytes)
 'c' (cylinders), '%' (% of total disk), '&' (% of free space).
Values in non-sector units are truncated to the nearest cylinder boundary.
> z
> w
> x
'/' must be configured!
The auto-allocated layout for sd0 is:
#                size           offset  fstype [fsize bsize  cpg]
  a:             1.0G                0  4.2BSD   2048 16384    1 # /
  b:             6.2G          2106432    swap
  c:            68.4G                0  unused
  d:             4.0G         15141888  4.2BSD   2048 16384    1 # /tmp
  e:             8.1G         23537088  4.2BSD   2048 16384    1 # /var
  f:             2.0G         40439424  4.2BSD   2048 16384    1 # /usr
  g:             1.0G         44642112  4.2BSD   2048 16384    1 # /usr/X11R6
  h:             8.1G         46748544  4.2BSD   2048 16384    1 # /usr/local
  i:             2.0G         63813696  4.2BSD   2048 16384    1 # /usr/src
  j:             2.0G         68016384  4.2BSD   2048 16384    1 # /usr/obj
  k:            33.9G         72219072  4.2BSD   2048 16384    1 # /home
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] e
Label editor (enter '?' for help at any prompt)
> l
# /dev/rsd0c:
type: SCSI
disk: SCSI disk
label: ST973402SSUN72G
duid: 0000000000000000
flags: vendor
bytes/sector: 512
sectors/track: 424
tracks/cylinder: 24
sectors/cylinder: 10176
cylinders: 14089
total sectors: 143374738
boundstart: 0
boundend: 143374738
drivedata: 0
...
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] A
/dev/rsd0a: 1028.5MB in 2106432 sectors of 512 bytes
6 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0k: 34741.5MB in 71150592 sectors of 512 bytes
172 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0d: 4099.2MB in 8395200 sectors of 512 bytes
21 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0f: 2052.1MB in 4202688 sectors of 512 bytes
11 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0g: 1028.5MB in 2106432 sectors of 512 bytes
6 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0h: 8332.6MB in 17065152 sectors of 512 bytes
42 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0j: 2052.1MB in 4202688 sectors of 512 bytes
11 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0i: 2052.1MB in 4202688 sectors of 512 bytes
11 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/rsd0e: 8253.1MB in 16902336 sectors of 512 bytes
41 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
/dev/sd0a (d44e56b406d1911c.a) on /mnt type ffs (rw, asynchronous, local)
/dev/sd0k (d44e56b406d1911c.k) on /mnt/home type ffs (rw,
asynchronous, local, nodev, nosuid)
/dev/sd0d (d44e56b406d1911c.d) on /mnt/tmp type ffs (rw, asynchronous,
local, nodev, nosuid)
/dev/sd0f (d44e56b406d1911c.f) on /mnt/usr type ffs (rw, asynchronous,
local, nodev)
/dev/sd0g (d44e56b406d1911c.g) on /mnt/usr/X11R6 type ffs (rw,
asynchronous, local, nodev)
/dev/sd0h (d44e56b406d1911c.h) on /mnt/usr/local type ffs (rw,
asynchronous, local, nodev)
/dev/sd0j (d44e56b406d1911c.j) on /mnt/usr/obj type ffs (rw,
asynchronous, local, nodev, nosuid)
/dev/sd0i (d44e56b406d1911c.i) on /mnt/usr/src type ffs (rw,
asynchronous, local, nodev, nosuid)
/dev/sd0e (d44e56b406d1911c.e) on /mnt/var type ffs (rw, asynchronous,
local, nodev, nosuid)

Let's install the sets!
Location of sets? (cd disk http or 'done') [cd]
Available CD-ROMs are: cd0.
Which CD-ROM contains the install media? (or 'done') [cd0]
Pathname to the sets? (or 'done') [5.6/sparc64]

Select sets by entering a set name, a file name pattern or 'all'. De-select
sets by prepending a '-' to the set name, file name pattern or 'all'. Selected
sets are labelled '[X]'.
    [X] bsd           [X] etc56.tgz     [ ] xbase56.tgz   [ ] xserv56.tgz
    [X] bsd.rd        [X] comp56.tgz    [ ] xetc56.tgz
    [X] bsd.mp        [X] man56.tgz     [ ] xshare56.tgz
    [X] base56.tgz    [X] game56.tgz    [ ] xfont56.tgz
Set name(s)? (or 'abort' or 'done') [done]
Directory does not contain SHA256.sig. Continue without verification? [no]
Location of sets? (cd disk http or 'done') [cd]
Available CD-ROMs are: cd0.
Which CD-ROM contains the install media? (or 'done') [cd0]
Pathname to the sets? (or 'done') [5.6/sparc64]

Select sets by entering a set name, a file name pattern or 'all'. De-select
sets by prepending a '-' to the set name, file name pattern or 'all'. Selected
sets are labelled '[X]'.
    [X] bsd           [X] etc56.tgz     [ ] xbase56.tgz   [ ] xserv56.tgz
    [X] bsd.rd        [X] comp56.tgz    [ ] xetc56.tgz
    [X] bsd.mp        [X] man56.tgz     [ ] xshare56.tgz
    [X] base56.tgz    [X] game56.tgz    [ ] xfont56.tgz
Set name(s)? (or 'abort' or 'done') [done]
Directory does not contain SHA256.sig. Continue without verification? [no]
Location of sets? (cd disk http or 'done') [cd]
Available CD-ROMs are: cd0.
Which CD-ROM contains the install media? (or 'done') [cd0]
Pathname to the sets? (or 'done') [5.6/sparc64]

Select sets by entering a set name, a file name pattern or 'all'. De-select
sets by prepending a '-' to the set name, file name pattern or 'all'. Selected
sets are labelled '[X]'.
    [X] bsd           [X] etc56.tgz     [ ] xbase56.tgz   [ ] xserv56.tgz
    [X] bsd.rd        [X] comp56.tgz    [ ] xetc56.tgz
    [X] bsd.mp        [X] man56.tgz     [ ] xshare56.tgz
    [X] base56.tgz    [X] game56.tgz    [ ] xfont56.tgz
Set name(s)? (or 'abort' or 'done') [done]
Directory does not contain SHA256.sig. Continue without verification? [no]
Location of sets? (cd disk http or 'done') [cd]
Available CD-ROMs are: cd0.
Which CD-ROM contains the install media? (or 'done') [cd0]
Pathname to the sets? (or 'done') [5.6/sparc64]
...
Select sets by entering a set name, a file name pattern or 'all'. De-select
sets by prepending a '-' to the set name, file name pattern or 'all'. Selected
sets are labelled '[X]'.
    [X] bsd           [X] etc56.tgz     [ ] xbase56.tgz   [ ] xserv56.tgz
    [X] bsd.rd        [X] comp56.tgz    [ ] xetc56.tgz
    [X] bsd.mp        [X] man56.tgz     [ ] xshare56.tgz
    [X] base56.tgz    [X] game56.tgz    [ ] xfont56.tgz
Set name(s)? (or 'abort' or 'done') [done]
Directory does not contain SHA256.sig. Continue without verification? [no]
Location of sets? (cd disk http or 'done') [cd] http
HTTP proxy URL? (e.g. '<a href="http://proxy:8080'">http://proxy:8080', or 'none') [none]
HTTP Server? (hostname, list#, 'done' or '?') [ftp.jaist.ac.jp]
Server directory? [pub/OpenBSD/5.6/sparc64]

Select sets by entering a set name, a file name pattern or 'all'. De-select
sets by prepending a '-' to the set name, file name pattern or 'all'. Selected
sets are labelled '[X]'.
    [X] bsd           [X] etc56.tgz     [ ] xbase56.tgz   [ ] xserv56.tgz
    [X] bsd.rd        [X] comp56.tgz    [ ] xetc56.tgz
    [X] bsd.mp        [X] man56.tgz     [ ] xshare56.tgz
    [X] base56.tgz    [X] game56.tgz    [ ] xfont56.tgz
Set name(s)? (or 'abort' or 'done') [done]
Get/Verify SHA256.sig   100% |**************************|  2161       00:00
Signature Verified
Get/Verify bsd          100% |**************************|  9017 KB    00:07
Get/Verify bsd.rd       100% |**************************|  2616 KB    00:04
Get/VeMar 29 01:06:17 sbcondb1 fmd: SOURCE: sde, REV: 1.16, CSN:
PX61035173  EVENT-ID: dfc125c9-b6d9-45ab-9f0c-5a9901b2c3d8 Refer to
http://www.fujitsu.com/sparcenterprise/msg/SCF-8003-HA for detailed
information.
exit from console.
XSCF>
XSCF>
...
XSCF> poweron -a
DomainIDs to power on:00
Continue? [y|n] :y
00 :Not powering on :Poweron canceled due to missing component.
XSCF> poweron -a
DomainIDs to power on:00
Continue? [y|n] :y
00 :Not powering on :Poweron canceled due to missing component.
XSCF> XSCF uboot  01080001  (May  8 2009 - 15:09:36)


XSCF uboot  01080001  (May  8 2009 - 15:09:36)

SCF board boot factor = 4080
memory test ..
Memory compare test
................finish
    DDR Real size: 256 MB
    DDR: 224 MB

## Booting image at ff800000 ...
   Image Name:   XSCF kernel 01090003 2.6.11.12-s
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1457048 Bytes =  1.4 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ff980000 ...
   Image Name:   XSCF rootfs 01090003 ,2010/07/01
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    5463455 Bytes =  5.2 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Ramdisk to 0baca000, end 0bfffd9f ... OK
Linux version 2.6.11.12-sec (gcc version 3.4.4) #1 Thu Jul 1 17:02:37 JST 2010
new message buffer at 0f700000 size 1048576
log_buf_len: 1048576
mpc85xx_cds_setup_arch
Built 1 zonelists
Kernel command line: root=/dev/ram rw console=ttyS0,9600
init=/sbin/init_change_root panic=1 mem=224M
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fbe79000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 218752k available (2188k kernel code, 668k data, 316k init, 0k highmem)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Freeing initrd memory: 5335k freed
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
i2c-algo-cpm: CPM2 I2C algorithm module version 0.1 (Mar 22, 2005)
FCC ENET Version 0.3
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
ip_tables: (C) 2000-2002 Netfilter core team
arp_tables: (C) 2002 David S. Miller
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 316k init
switching initrd filesystem, ramdisk to tmpfs
SCF Linux Boot Script 2006/03/04 for ROM boot environment
fsl-sec2 hardware crypt accelerator model3a ver 0.02 enabled

XSCF initial process start (pid=106)

load /scf/modules/lites_ldrv.ko  --  complete
load /scf/modules/drvscftrace.ko  --  complete
load /scf/modules/sec2_rsa.ko  --  complete
load /scf/modules/sec2_md5.ko  --  complete
load /scf/modules/sec2_des.ko  --  complete
load /scf/modules/sec2_arc4.ko  --  complete
load /scf/modules/sec2_aes.ko  --  complete
load /scf/modules/sec2_sha256.ko  --  complete
load /scf/modules/sec2_sha1.ko  --  complete
load /scf/modules/hw_random.ko  --  complete
load /scf/modules/scsi_mod.ko  --  complete
load /scf/modules/sd_mod.ko  --  complete
load /scf/modules/usbcore.ko  --  complete
load /scf/modules/ohci-hcd.ko  --  complete
load /scf/modules/usb-storage.ko  --  complete
load /scf/modules/drvbootfmem.ko  --  complete
load /scf/modules/drvmbc.ko  --  complete
load /scf/modules/drvnand.ko  --  complete
load /scf/modules/drvffc.ko  --  complete
load /scf/modules/drvffcint.ko  --  complete
load /scf/modules/drvrtc.ko  --  complete
load /scf/modules/drvxscfuart.ko  --  complete
load /scf/modules/drvrci.ko  --  complete
load /scf/modules/drvtimer.ko  --  complete
load /scf/modules/drvsdic.ko  --  complete
load /scf/modules/sm2s.ko  --  complete
load /scf/modules/spkmdrv.ko  --  complete
mount /dev/mtdblock0 -> /hcp0/linux  --  complete
mount /dev/mtdblock1 -> /hcp0/scfprog  --  complete
mount /dev/mtdblock2 -> /hcp0/gendata  --  complete
mount /dev/mtdblock3 -> /hcp0/remcscm  --  complete
mount /dev/mtdblock4 -> /hcpcommon/setup  --  complete
mount /dev/mtdblock5 -> /hcpcommon/obp  --  complete
mount /dev/mtdblock6 -> /hcpcommon/tmp  --  complete
mount /dev/mtdblock11 -> /hcpcommon/var  --  complete
mount /dev/mtdblock12 -> /hcpcommon/scflog1  --  complete
mount /dev/mtdblock13 -> /hcpcommon/scflog2  --  complete
execute S00mtab  --  complete
execute S00portmap  --  complete
execute S00tmpmake  --  complete
execute S00varclean  --  complete
execute S10ldconfig  --  complete
execute S15last_dmesg  --  complete
execute S20cfgcreate  --  complete
execute S50iptables  --  complete
execute S60check  --  complete
execute S61restore  --  complete
execute S99syslogd  --  complete
initialize XSCF common database (STANDALONE)  --  complete
start /scf/sbin/dbs (pid=336)
start /scf/sbin/ksyseventd (pid=337)
start /scf/sbin/syseventd (pid=342)
start /scf/init/scf_cmgrd (pid=350)
start /scf/init/scf_coremgr (pid=351)
start /scf/init/dualprocess (pid=352)
check SCF operation mode (for OPNL access)  --  complete
initialize OPNL  --  complete
check SCF operation mode  --  complete (ACTIVE)
start /scf/sbin/dbs (pid=371)
initialize XSCF common database (OWN)  --  complete
synchronize setup data (XSCF -> OPNL)  --  complete
initialize XSCF common database (ACTIVE)  --  complete
wait for database synchronization  --  complete
execute S00clis_all  --  complete
execute S10restore_ad  --  complete
execute S10restore_um  --  complete
execute S11network.sheth0: PHY is Intel LXT972A (1378e2)
  --  complete
execute S15ntpcheck.sh  --  complete
execute S21daemons  --  complete
execute S51scflog_SCFboot.sh  --  complete
execute S82cod  --  complete
execute S98bui  --  complete
execute S00clis_active  --  complete
execute S00cmem_check  --  complete
execute S00tmp_login  --  complete
execute S18restorefmdlog  --  complete
execute S19setfmurl  --  complete
execute S29setfmconf  --  complete
execute S50setupSCFboot.sh  --  complete
execute S83setservicetagdata  --  complete
start /scf/sbin/scf_panelmgr (pid=801)
start /scf/sbin/fmdsyncd (pid=802)
start /scf/sbin/auditd (pid=804)
start /scf/sbin/cmd (pid=805)
start /scf/sbin/cmd_sub (pid=806)
start /scf/sbin/errhandd (pid=807)
start /scf/sbin/fjdrd (pid=808)
start /scf/sbin/frura (pid=809)
start /scf/sbin/mond (pid=810)
start /scf/sbin/mond (pid=811)
start /scf/sbin/powerd (pid=812)
start /scf/sbin/rci (pid=813)
start /scf/sbin/rci_dual (pid=814)
start /scf/sbin/reset (pid=815)
start /scf/sbin/resetra (pid=816)
start /scf/sbin/rsyncprocess (pid=817)
start /scf/sbin/scf_firmup_exed (pid=818)
start /scf/sbin/scf_hardlog (pid=819)
start /scf/sbin/scf_loganalyze (pid=820)
start /scf/sbin/scf_procmeas (pid=821)
start /scf/sbin/sequence (pid=822)
start /scf/sbin/ttyd (pid=823)
start /scf/sbin/rm_eventd (pid=824)
start /scf/sbin/rm_queued (pid=825)
start /scf/sbin/apcsd (pid=826)
start /scf/sbin/codd (pid=827)
start /scf/sbin/scf_firmup_ctld (pid=828)
start /scf/sbin/fmd (pid=829)
start /scf/sbin/dscpd (pid=1013)
start /scf/sbin/monitor_msg (pid=1014)
start /scf/sbin/picld (pid=1015)
start /scf/sbin/sunmcrund (pid=1016)
start /scf/sbin/dfrud (pid=1017)
start /scf/sbin/iomgrd (pid=1018)
start /scf/sbin/archd (pid=1050)
wait for SCF_READY  --  complete
execute S20setupSCFready.sh  --  complete
execute S99rcclear  --  complete
execute S10iobox_scan  --  complete
execute S10restore_ad  --  complete
execute S10restore_um  --  complete
execute S84snmpd  --  complete
execute S85sunmc_esd  --  complete
execute S86limits  --  complete
execute S87opnl  --  complete
execute S99dr_recover.sh  --  complete
XSCF Initialize complete.

Mar 29 01:44:53 sbcondb1 XSCF[106]: XSCF Initialize complete.

login:

login: default
Change the panel mode switch to Locked and press return...
Leave it in that position for at least 5 seconds.  Change the panel
mode switch to Service, and press return...
XSCF> poweron -a
DomainIDs to power on:00
Continue? [y|n] :y
00 :Not powering on :Poweron canceled due to missing component.
...
XSCF> restoredefaults
Permission denied.
XSCF> showstatus
*   MBU_A Status:Faulted;
*       CPU Status:Deconfigured;
*       MEM#0A Status:Deconfigured;
*       MEM#0B Status:Deconfigured;
*       MEM#1A Status:Deconfigured;
*       MEM#1B Status:Deconfigured;
*       MEM#2A Status:Deconfigured;
*       MEM#2B Status:Deconfigured;
*       MEM#3A Status:Deconfigured;
*       MEM#3B Status:Deconfigured;
XSCF> showhardconf
SPARC Enterprise M3000;
    + Serial:PX61035173; Operator_Panel_Switch:Service;
    + Power_Supply_System:Single; SCF-ID:XSCF#0;
    + System_Power:Off; System_Phase:Cabinet Power Off;
    Domain#0 Domain_Status:Powered Off;

*   MBU_A Status:Faulted; Ver:0401h; Serial:PP103503BF  ;
        + FRU-Part-Number:CA07082-D061 E0   /541-4282-05          ;
*       + CPU Status:Deconfigured;
            + Freq:2.750 GHz; Type:32;
            + Core:2; Strand:2;
        + Memory_Size:32 GB;
*       MEM#0A Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e0682857;
            + Type:4B; Size:4 GB;
*       MEM#0B Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e0682855;
            + Type:4B; Size:4 GB;
*       MEM#1A Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e068285a;
            + Type:4B; Size:4 GB;
*       MEM#1B Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e0682858;
            + Type:4B; Size:4 GB;
*       MEM#2A Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e068285c;
            + Type:4B; Size:4 GB;
*       MEM#2B Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e0682859;
            + Type:4B; Size:4 GB;
*       MEM#3A Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e068285b;
            + Type:4B; Size:4 GB;
*       MEM#3B Status:Deconfigured;
            + Code:2c000000000000000836HTF51272PY-667G10100-e0682853;
            + Type:4B; Size:4 GB;
    OPNL Status:Normal; Ver:0101h; Serial:PP10350414  ;
        + FRU-Part-Number:CA07082-D021 A2   /541-3306-01          ;
    PSU#0 Status:Normal; Serial:EA1019A011;
        + FRU-Part-Number:CA01022-0720 10K  /300-2193-10   ;
        + Power_Status:Input fail;
        + Type:AC;
    PSU#1 Status:Normal; Serial:EA1019A013;
        + FRU-Part-Number:CA01022-0720 10K  /300-2193-10   ;
        + Power_Status:Off;
        + Type:AC;
    FANBP_B Status:Normal; Ver:0101h; Serial:PP103503ZJ  ;
        + FRU-Part-Number:CA20399-B12X 009AC/541-3304-03          ;
        FAN_A#0 Status:Normal;
        FAN_A#1 Status:Normal;
XSCF> showbords -a
shell: showbords: command not found
XSCF> showboards -a
XSB  DID(LSB) Assignment  Pwr  Conn Conf Test    Fault
---- -------- ----------- ---- ---- ---- ------- --------
00-0 00(00)   Unavailable n    n    n    Unknown Faulted
...

-------------------------------------------------------------------------------------

I wish for the development of OpenBSD/sparc64...


--
Naruaki.Etomi
[hidden email]

Loading...