Intel D201GLY2 install failure, OpenBSD 4.4

classic Classic list List threaded Threaded
6 messages Options
Reply | Threaded
Open this post in threaded view
|

Intel D201GLY2 install failure, OpenBSD 4.4

Jamie Cuesta
I'm booting from CD as prelude to install, and during CD boot see (NOTE this is manually transcribed from the screen):

: couldn't map interrupt
sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91pci_intr_map: bad interrupt line 19
: couldn't map interrupt
pciide1 at pci0 dev 5 function 0 "SiS 181 SATA" rev 0x01: DMA
pci_intr_map: bad interrupt line 17
pciide1: couldn't map native-PCI interrupt
pci_intr_map: bad interrupt line 17
pciide1: couldn't map native-PCI interrupt
ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00
pci2 at ppb1 bus 2
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x2f8/8 irq 4: ns 16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
biomask ffed netmask ffed ttymask ffff
rd0: fixed, 3800 blocks
softraid at root
root on rd0a swap on rd0b dump on rd0b
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
(I)nstall, (U)pgrade or (S)hell?

I choose install, accept defaults for terminal type, answer 'y' to "Proceed with install? [no]" and get:

No disks found.
#

This system has a IDE CD-RW drive, and two SATA HDD's.  After failing OpenBSD 4.4 install last week, I installed Debian stable on this system w/no problems.  But I'd rather use OpenBSD so reporting this problem in hopes it can be fixed (mobo is a nice low-cost fanless mini-ITX, so could appeal to many).  My web searches show this problem being reported occasionally in the past but none I saw no reports for this mobo with 4.4 release.

I was hoping to include a dmesg via serial port capture (my box does not include a floppy), but

boot> set tty com0
switching console to com0
com0 console not present

Web searches suggested I could mess with the BIOS to get around this problem, but the only BIOS setting for the serial port is enable/disable: I switched to disable mode with no change in results.

FWIW, Jaime

Reply | Threaded
Open this post in threaded view
|

Re: Intel D201GLY2 install failure, OpenBSD 4.4

Ted Unangst-2
On Thu, Nov 6, 2008 at 11:49 AM, Jamie Cuesta <[hidden email]> wrote:
> I was hoping to include a dmesg via serial port capture (my box does not include a floppy), but

Use ftp.

Reply | Threaded
Open this post in threaded view
|

Re: Intel D201GLY2 install failure, OpenBSD 4.4

Jamie Cuesta
In reply to this post by Jamie Cuesta
> From: Ted Unangst <[hidden email]>
> Subject: Re: Intel D201GLY2 install failure, OpenBSD 4.4
> To: [hidden email]
> Cc: [hidden email]
> Date: Thursday, November 6, 2008, 1:24 PM
> On Thu, Nov 6, 2008 at 11:49 AM, Jamie Cuesta
> <[hidden email]> wrote:
> > I was hoping to include a dmesg via serial port
> capture (my box does not include a floppy), but
>
> Use ftp.

First: I'm a noob, so some of what follows may be utterly basic and ignorant.

It seems that in order to use the ftp option, I need a functioning network interface(?).  However when I boot using the install CD and choose "(s)hell", here's what I see:

# ifconfig
lo0: flags=8008<LOOPBACK,MULTICAST> mtu 33204
        groups: lo
#

Note that one of the boot messages in my first post seemed to indicate that the on-Mobo NIC was among the devices affected by a "bad interrupt" problem:

sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91pci_intr_map: bad interrupt line 19
: couldn't map interrupt

Is there any way around this (involving only the shell available to me now)?  If not, I suppose I'll see if I can dig a floppy drive out of my bonepile and pray that _it_ works.

Thanks, Jaime

Reply | Threaded
Open this post in threaded view
|

Re: Intel D201GLY2 install failure, OpenBSD 4.4

Ted Unangst-2
On Fri, Nov 7, 2008 at 8:54 AM, Jamie Cuesta <[hidden email]> wrote:

> It seems that in order to use the ftp option, I need a functioning network interface(?).  However when I boot using the install CD and choose "(s)hell", here's what I see:
>
> # ifconfig
> lo0: flags=8008<LOOPBACK,MULTICAST> mtu 33204
>        groups: lo
> #
>
> Note that one of the boot messages in my first post seemed to indicate that the on-Mobo NIC was among the devices affected by a "bad interrupt" problem:
>
> sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91pci_intr_map: bad interrupt line 19
> : couldn't map interrupt

Ok, you are having serious interrupt issues.  The only thing I can
think of to try is disabling acpi (via boot -c), but that's a long
shot.

Reply | Threaded
Open this post in threaded view
|

Re: Intel D201GLY2 install failure, OpenBSD 4.4

Lévai, Dániel
In reply to this post by Ted Unangst-2
On Thursday 06 November 2008 22.24.49 Ted Unangst wrote:
> On Thu, Nov 6, 2008 at 11:49 AM, Jamie Cuesta <[hidden email]>
wrote:
> > I was hoping to include a dmesg via serial port capture (my box
> > does not include a floppy), but
>
> Use ftp.

On Friday 07 November 2008 17.24.52 Ted Unangst wrote:
> Ok, you are having serious interrupt issues.  The only thing I can
> think of to try is disabling acpi (via boot -c), but that's a long
> shot.

I have the same board, and can confirm that without disabling
acpi, -current OpenBSD can not recognize the network device, the hard
drive nor the attached usb devices (disk, keyboard etc...).
However, after disabling acpi, -current fires up, and recognizes the
hard drives and the network card. That's how I could manage to get a
dmesg. So here it is, and also sent to dmesg@:

OpenBSD 4.4-current (RAMDISK_CD) #964: Fri Nov  7 03:25:28 MST 2008
    [hidden email]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel(R) Celeron(R) CPU 220 @ 1.20GHz ("GenuineIntel" 686-class)
1.21 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR
real mem  = 1033404416 (985MB)
avail mem = 992567296 (946MB)
User Kernel Config
UKC> disable acpi
241 acpi0 disabled
UKC> quit
Continuing...
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/04/08, SMBIOS rev. 2.4 @
0xe4da0 (23 entries)
bios0: vendor Intel Corp. version "LY66210M.86A.0137.2008.0104.1540"
date 01/04/2008
bios0: Intel Corporation D201GLY
acpi at bios0 function 0x0 not configured
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc0000/0x10000
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "SiS 662 PCI" rev 0x01
ppb0 at pci0 dev 1 function 0 "SiS 648FX AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "SiS 6330 VGA" rev 0x04
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 2 function 0 "SiS 964 ISA" rev 0x36
pciide0 at pci0 dev 2 function 5 "SiS 5513 EIDE" rev 0x01: 964: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4120B, A111> ATAPI
5/cdrom removable
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
"SiS 7012 AC97" rev 0xa0 at pci0 dev 2 function 7 not configured
ohci0 at pci0 dev 3 function 0 "SiS 5597/5598 USB" rev 0x0f: irq 11,
version 1.0, legacy support
ohci1 at pci0 dev 3 function 1 "SiS 5597/5598 USB" rev 0x0f: irq 10,
version 1.0, legacy support
ohci2 at pci0 dev 3 function 2 "SiS 5597/5598 USB" rev 0x0f: irq 11,
version 1.0, legacy support
ehci0 at pci0 dev 3 function 3 "SiS 7002 USB" rev 0x00: irq 10
ehci0: timed out waiting for BIOS
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "SiS EHCI root hub" rev 2.00/1.00 addr 1
sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91: irq 11,
address 00:1c:c0:41:23:6b
ukphy0 at sis0 phy 1: Generic IEEE 802.3u media interface, rev. 1: OUI
0x0050ef, model 0x0007
pciide1 at pci0 dev 5 function 0 "SiS 181 SATA" rev 0x01: DMA
pciide1: using irq 10 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <FUJITSU MHW2060BH>
wd0: 16-sector PIO, LBA48, 57226MB, 117199616 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
rl0 at pci0 dev 6 function 0 "Realtek 8139" rev 0x10: irq 10, address
00:30:4f:19:3e:fd
rlphy0 at rl0 phy 0: RTL internal PHY
ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00
pci2 at ppb1 bus 2
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3 "SiS OHCI root hub" rev 1.00/1.00 addr 1
biomask fffd netmask fffd ttymask ffff
rd0: fixed, 3800 blocks
uhidev0 at uhub1 port 2 configuration 1 interface 0 "Logitech Logitech
USB Keyboard" rev 1.10/15.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 2 configuration 1 interface 1 "Logitech Logitech
USB Keyboard" rev 1.10/15.00 addr 2
uhidev1: iclass 3/0, 3 report ids
uhid at uhidev1 reportid 1 not configured
uhid at uhidev1 reportid 2 not configured
uhid at uhidev1 reportid 3 not configured
softraid0 at root
root on rd0a swap on rd0b dump on rd0b

Daniel

--
LEVAI Daniel
PGP key ID = 0x4AC0A4B1
Key fingerprint = D037 03B9 C12D D338 4412  2D83 1373 917A 4AC0 A4B1

Reply | Threaded
Open this post in threaded view
|

Re: Intel D201GLY2 install failure, OpenBSD 4.4

Jamie Cuesta
In reply to this post by Ted Unangst-2
Thanks to LEVAI Daniel for providing his dmesg.  To add mere confirmation, I too was able to boot 4.4 release with NIC interface active/recognized after 'boot -c' + 'disable acpi', however I was unable to muster the skill to accomplish the ftp transfer.  Is Daniel's dmesg sufficient for debug, or would a capture of a default-config dmesg (with all its error messages) be beneficial?  If the latter, I will endeavor to connect a floppy drive...

Jaime

--- On Fri, 11/7/08, Ted Unangst <[hidden email]> wrote:

> From: Ted Unangst <[hidden email]>
> Subject: Re: Intel D201GLY2 install failure, OpenBSD 4.4
> To: [hidden email]
> Cc: [hidden email]
> Date: Friday, November 7, 2008, 9:24 AM
> On Fri, Nov 7, 2008 at 8:54 AM, Jamie Cuesta
> <[hidden email]> wrote:
> > It seems that in order to use the ftp option, I need a
> functioning network interface(?).  However when I boot using
> the install CD and choose "(s)hell", here's
> what I see:
> >
> > # ifconfig
> > lo0: flags=8008<LOOPBACK,MULTICAST> mtu 33204
> >        groups: lo
> > #
> >
> > Note that one of the boot messages in my first post
> seemed to indicate that the on-Mobo NIC was among the
> devices affected by a "bad interrupt" problem:
> >
> > sis0 at pci0 dev 4 function 0 "SiS 900
> 10/100BaseTX" rev 0x91pci_intr_map: bad interrupt line
> 19
> > : couldn't map interrupt
>
> Ok, you are having serious interrupt issues.  The only
> thing I can
> think of to try is disabling acpi (via boot -c), but
> that's a long
> shot.