Intel 1G ethernet card works just at 100baseTX under em(4)

classic Classic list List threaded Threaded
2 messages Options
Reply | Threaded
Open this post in threaded view
|

Intel 1G ethernet card works just at 100baseTX under em(4)

Walter Alejandro Iglesias-3
$ dmesg | grep em0
em0 at pci0 dev 25 function 0 "Intel ICH8 IGP AMT" rev 0x02: msi, address 00:0f:fe:77:4f:df
$ cat /etc/hostname.em0
dhcp
$ ifconfig em0
em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
        lladdr 00:0f:fe:77:4f:df
        index 1 priority 0 llprio 3
        groups: egress
        media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
        status: active
        inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
$ ifconfig em0 media
em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
        lladdr 00:0f:fe:77:4f:df
        index 1 priority 0 llprio 3
        groups: egress
        media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
        status: active
        supported media:
                media 10baseT
                media 10baseT mediaopt full-duplex
                media 100baseTX
                media 100baseTX mediaopt full-duplex
                media 1000baseT mediaopt full-duplex
                media 1000baseT
                media autoselect
        inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
# ifconfig em0 media media 1000baseT mediaopt full-duplex
# ifconfig em0
em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
        lladdr 00:0f:fe:77:4f:df
        index 1 priority 0 llprio 3
        groups: egress
        media: Ethernet 1000baseT full-duplex (none)
        status: no carrier
        inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
# ifconfig em0 media autoselect
# ifconfig em0
em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
        lladdr 00:0f:fe:77:4f:df
        index 1 priority 0 llprio 3
        groups: egress
        media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
        status: active
        inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255


I ran the above commands consecutively, without delay.  As they show,
after I set "media" to "1000baseT full-duplex" (available according to
ifconfig output) connection is lost, then I set media back to
"autoselect" and the connection is immediately reestablished.

Tried with another (tested) cable, same result.  Tried connecting the PC
to another router, same result.  With an old linux liveCD the card works
at 1G speed by default.


dmesg:
OpenBSD 6.6-beta (GENERIC.MP) #246: Sat Aug 24 09:18:54 MDT 2019
    [hidden email]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 4135260160 (3943MB)
avail mem = 3997245440 (3812MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xeb920 (70 entries)
bios0: vendor Hewlett-Packard version "786E1 v01.16" date 08/17/2011
bios0: Hewlett-Packard HP Compaq dc7700 Convertible Minitower
acpi0 at bios0: ACPI 1.0
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC ASF! MCFG TCPA SLIC HPET
acpi0: wakeup devices PCI0(S4) COM1(S4) PEG1(S4) IGBE(S4) PCX1(S4) PCX2(S4) HUB_(S4) USB1(S3) USB2(S3) USB3(S3) USB4(S3) USB5(S3) EUS1(S3) EUS2(S3) PBTN(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM)2 CPU 4300 @ 1.80GHz, 1795.78 MHz, 06-0f-02
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN
cpu0: 2MB 64b/line 8-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 199MHz
cpu0: mwait min=64, max=64, C-substates=0.2, IBE
cpu1 at mainbus0: apid 1 (application processor)
TSC skew=-22
cpu1: Intel(R) Core(TM)2 CPU 4300 @ 1.80GHz, 1795.50 MHz, 06-0f-02
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN
cpu1: 2MB 64b/line 8-way L2 cache
cpu1: smt 0, core 1, package 0
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins, remapped
acpimcfg0 at acpi0
acpimcfg0: addr 0xf4000000, bus 0-63
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (PEG1)
acpiprt2 at acpi0: bus 32 (PCX1)
acpiprt3 at acpi0: bus -1 (PCX2)
acpiprt4 at acpi0: bus 7 (HUB_)
acpicpu0 at acpi0: C1(@1 halt!), PSS
acpicpu1 at acpi0: C1(@1 halt!), PSS
acpipci0 at acpi0 PCI0: 0x00000000 0x00000011 0x00000001
acpicmos0 at acpi0
"PNP0003" at acpi0 not configured
acpibtn0 at acpi0: PBTN
"PNP0C14" at acpi0 not configured
cpu0: Enhanced SpeedStep 1795 MHz: speeds: 1800, 1200 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel 82Q965 Host" rev 0x02
inteldrm0 at pci0 dev 2 function 0 "Intel 82Q965 Video" rev 0x02
drm0 at inteldrm0
intagp0 at inteldrm0
agp0 at intagp0: aperture at 0xe0000000, size 0x10000000
inteldrm0: apic 1 int 16
"Intel 82Q965 HECI" rev 0x02 at pci0 dev 3 function 0 not configured
em0 at pci0 dev 25 function 0 "Intel ICH8 IGP AMT" rev 0x02: msi, address 00:0f:fe:77:4f:df
uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x02: apic 1 int 20
uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x02: apic 1 int 21
ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x02: apic 1 int 22
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x02: msi
azalia0: codecs: Realtek ALC262
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x02: msi
pci1 at ppb0 bus 32
uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x02: apic 1 int 20
uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x02: apic 1 int 21
ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x02: apic 1 int 20
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xf2
pci2 at ppb1 bus 7
pcib0 at pci0 dev 31 function 0 "Intel 82801HO LPC" rev 0x02
pciide0 at pci0 dev 31 function 2 "Intel 82801H SATA" rev 0x02: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 1 int 18 for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD1600AAJS-08WAA0>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <TSSTcorp, DVD-ROM TS-H353B, BC03> ATAPI 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 5
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
uhidev0 at uhub3 port 2 configuration 1 interface 0 "EATON Eaton 3S" rev 2.00/1.00 addr 2
uhidev0: iclass 3/0, 32 report ids
upd0 at uhidev0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on wd0a (4aeef12f7b9611d5.a) swap on wd0b dump on wd0b
[drm] ACPI BIOS requests an excessive sleep of 858477105 ms, using 1500 ms instead
inteldrm0: 1360x768, 32bpp
wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using wskbd0
wsdisplay0: screen 1-5 added (std, vt100 emulation)

usbdevs:
Controller /dev/usb0:
addr 01: 8086:0000 Intel, EHCI root hub
         high speed, self powered, config 1, rev 1.00
         driver: uhub0
Controller /dev/usb1:
addr 01: 8086:0000 Intel, EHCI root hub
         high speed, self powered, config 1, rev 1.00
         driver: uhub1
Controller /dev/usb2:
addr 01: 8086:0000 Intel, UHCI root hub
         full speed, self powered, config 1, rev 1.00
         driver: uhub2
Controller /dev/usb3:
addr 01: 8086:0000 Intel, UHCI root hub
         full speed, self powered, config 1, rev 1.00
         driver: uhub3
addr 02: 0463:ffff EATON, Eaton 3S
         low speed, power 20 mA, config 1, rev 1.00, iSerial 000000000
         driver: uhidev0
Controller /dev/usb4:
addr 01: 8086:0000 Intel, UHCI root hub
         full speed, self powered, config 1, rev 1.00
         driver: uhub4
Controller /dev/usb5:
addr 01: 8086:0000 Intel, UHCI root hub
         full speed, self powered, config 1, rev 1.00
         driver: uhub5


Reply | Threaded
Open this post in threaded view
|

UPDATE: Intel 1G ethernet card works just at 100baseTX under em(4)

Walter Alejandro Iglesias-3
Today I tried with a FreeBSD live cd.  With the FreeBSD driver happens
almost the same, by default it selects 100baseTX, except for that if I
manually run:

  # ifconfig em0 autoselect

it sometimes changes to 1000baseT, but the connection goes down.
Same selecting 1000baseT manually.

I don't know if this could be useful.  While media 1000baseT is set,
freebsd kernel continuously prints this message:

  # em0: TX(0) desc avail=1024, pidx=0

When I select 100baseTX again those messages go away and the connection
is reestablished.

I tried also with another linux distribution, linux recognizes the card
as 1G by default.

I even cleaned up the ethernet port connectors with alcohol. :-)  The
ethernet cables I've been using are cat5E.  I'll try buying some cat6 or
cat7 to be sure it's not a cable issue.



On Mon, Aug 26, 2019 at 04:24:06PM +0200, Walter Alejandro Iglesias wrote:

> $ dmesg | grep em0
> em0 at pci0 dev 25 function 0 "Intel ICH8 IGP AMT" rev 0x02: msi, address 00:0f:fe:77:4f:df
> $ cat /etc/hostname.em0
> dhcp
> $ ifconfig em0
> em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
> lladdr 00:0f:fe:77:4f:df
> index 1 priority 0 llprio 3
> groups: egress
> media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
> status: active
> inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
> $ ifconfig em0 media
> em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
> lladdr 00:0f:fe:77:4f:df
> index 1 priority 0 llprio 3
> groups: egress
> media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
> status: active
> supported media:
> media 10baseT
> media 10baseT mediaopt full-duplex
> media 100baseTX
> media 100baseTX mediaopt full-duplex
> media 1000baseT mediaopt full-duplex
> media 1000baseT
> media autoselect
> inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
> # ifconfig em0 media media 1000baseT mediaopt full-duplex
> # ifconfig em0
> em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
> lladdr 00:0f:fe:77:4f:df
> index 1 priority 0 llprio 3
> groups: egress
> media: Ethernet 1000baseT full-duplex (none)
> status: no carrier
> inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
> # ifconfig em0 media autoselect
> # ifconfig em0
> em0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu 1500
> lladdr 00:0f:fe:77:4f:df
> index 1 priority 0 llprio 3
> groups: egress
> media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
> status: active
> inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
>
>
> I ran the above commands consecutively, without delay.  As they show,
> after I set "media" to "1000baseT full-duplex" (available according to
> ifconfig output) connection is lost, then I set media back to
> "autoselect" and the connection is immediately reestablished.
>
> Tried with another (tested) cable, same result.  Tried connecting the PC
> to another router, same result.  With an old linux liveCD the card works
> at 1G speed by default.
>
>
> dmesg:
> OpenBSD 6.6-beta (GENERIC.MP) #246: Sat Aug 24 09:18:54 MDT 2019
>     [hidden email]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> real mem = 4135260160 (3943MB)
> avail mem = 3997245440 (3812MB)
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xeb920 (70 entries)
> bios0: vendor Hewlett-Packard version "786E1 v01.16" date 08/17/2011
> bios0: Hewlett-Packard HP Compaq dc7700 Convertible Minitower
> acpi0 at bios0: ACPI 1.0
> acpi0: sleep states S0 S3 S4 S5
> acpi0: tables DSDT FACP APIC ASF! MCFG TCPA SLIC HPET
> acpi0: wakeup devices PCI0(S4) COM1(S4) PEG1(S4) IGBE(S4) PCX1(S4) PCX2(S4) HUB_(S4) USB1(S3) USB2(S3) USB3(S3) USB4(S3) USB5(S3) EUS1(S3) EUS2(S3) PBTN(S4)
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: Intel(R) Core(TM)2 CPU 4300 @ 1.80GHz, 1795.78 MHz, 06-0f-02
> cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN
> cpu0: 2MB 64b/line 8-way L2 cache
> cpu0: smt 0, core 0, package 0
> mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
> cpu0: apic clock running at 199MHz
> cpu0: mwait min=64, max=64, C-substates=0.2, IBE
> cpu1 at mainbus0: apid 1 (application processor)
> TSC skew=-22
> cpu1: Intel(R) Core(TM)2 CPU 4300 @ 1.80GHz, 1795.50 MHz, 06-0f-02
> cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN
> cpu1: 2MB 64b/line 8-way L2 cache
> cpu1: smt 0, core 1, package 0
> ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins, remapped
> acpimcfg0 at acpi0
> acpimcfg0: addr 0xf4000000, bus 0-63
> acpihpet0 at acpi0: 14318179 Hz
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus -1 (PEG1)
> acpiprt2 at acpi0: bus 32 (PCX1)
> acpiprt3 at acpi0: bus -1 (PCX2)
> acpiprt4 at acpi0: bus 7 (HUB_)
> acpicpu0 at acpi0: C1(@1 halt!), PSS
> acpicpu1 at acpi0: C1(@1 halt!), PSS
> acpipci0 at acpi0 PCI0: 0x00000000 0x00000011 0x00000001
> acpicmos0 at acpi0
> "PNP0003" at acpi0 not configured
> acpibtn0 at acpi0: PBTN
> "PNP0C14" at acpi0 not configured
> cpu0: Enhanced SpeedStep 1795 MHz: speeds: 1800, 1200 MHz
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "Intel 82Q965 Host" rev 0x02
> inteldrm0 at pci0 dev 2 function 0 "Intel 82Q965 Video" rev 0x02
> drm0 at inteldrm0
> intagp0 at inteldrm0
> agp0 at intagp0: aperture at 0xe0000000, size 0x10000000
> inteldrm0: apic 1 int 16
> "Intel 82Q965 HECI" rev 0x02 at pci0 dev 3 function 0 not configured
> em0 at pci0 dev 25 function 0 "Intel ICH8 IGP AMT" rev 0x02: msi, address 00:0f:fe:77:4f:df
> uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x02: apic 1 int 20
> uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x02: apic 1 int 21
> ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x02: apic 1 int 22
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x02: msi
> azalia0: codecs: Realtek ALC262
> audio0 at azalia0
> ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x02: msi
> pci1 at ppb0 bus 32
> uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x02: apic 1 int 20
> uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x02: apic 1 int 21
> ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x02: apic 1 int 20
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xf2
> pci2 at ppb1 bus 7
> pcib0 at pci0 dev 31 function 0 "Intel 82801HO LPC" rev 0x02
> pciide0 at pci0 dev 31 function 2 "Intel 82801H SATA" rev 0x02: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
> pciide0: using apic 1 int 18 for native-PCI interrupt
> wd0 at pciide0 channel 0 drive 0: <WDC WD1600AAJS-08WAA0>
> wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
> atapiscsi0 at pciide0 channel 1 drive 0
> scsibus1 at atapiscsi0: 2 targets
> cd0 at scsibus1 targ 0 lun 0: <TSSTcorp, DVD-ROM TS-H353B, BC03> ATAPI 5/cdrom removable
> cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 5
> usb2 at uhci0: USB revision 1.0
> uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci1: USB revision 1.0
> uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb4 at uhci2: USB revision 1.0
> uhub4 at usb4 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb5 at uhci3: USB revision 1.0
> uhub5 at usb5 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> isa0 at pcib0
> isadma0 at isa0
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> pckbd0 at pckbc0 (kbd slot)
> wskbd0 at pckbd0: console keyboard
> pms0 at pckbc0 (aux slot)
> wsmouse0 at pms0 mux 0
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> lpt0 at isa0 port 0x378/4 irq 7
> uhidev0 at uhub3 port 2 configuration 1 interface 0 "EATON Eaton 3S" rev 2.00/1.00 addr 2
> uhidev0: iclass 3/0, 32 report ids
> upd0 at uhidev0
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> root on wd0a (4aeef12f7b9611d5.a) swap on wd0b dump on wd0b
> [drm] ACPI BIOS requests an excessive sleep of 858477105 ms, using 1500 ms instead
> inteldrm0: 1360x768, 32bpp
> wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using wskbd0
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
>
> usbdevs:
> Controller /dev/usb0:
> addr 01: 8086:0000 Intel, EHCI root hub
> high speed, self powered, config 1, rev 1.00
> driver: uhub0
> Controller /dev/usb1:
> addr 01: 8086:0000 Intel, EHCI root hub
> high speed, self powered, config 1, rev 1.00
> driver: uhub1
> Controller /dev/usb2:
> addr 01: 8086:0000 Intel, UHCI root hub
> full speed, self powered, config 1, rev 1.00
> driver: uhub2
> Controller /dev/usb3:
> addr 01: 8086:0000 Intel, UHCI root hub
> full speed, self powered, config 1, rev 1.00
> driver: uhub3
> addr 02: 0463:ffff EATON, Eaton 3S
> low speed, power 20 mA, config 1, rev 1.00, iSerial 000000000
> driver: uhidev0
> Controller /dev/usb4:
> addr 01: 8086:0000 Intel, UHCI root hub
> full speed, self powered, config 1, rev 1.00
> driver: uhub4
> Controller /dev/usb5:
> addr 01: 8086:0000 Intel, UHCI root hub
> full speed, self powered, config 1, rev 1.00
> driver: uhub5
>
>