Belinea s.Book1 can't boot OpenBSD

classic Classic list List threaded Threaded
4 messages Options
Reply | Threaded
Open this post in threaded view
|

Belinea s.Book1 can't boot OpenBSD

Denis Fondras
Hello,

I'm currently testing a Belinea s.Book1 microlaptop
(http://www.belinea.com/en/s_line/product_tagline.jsp?node=652&artnr=399501)
and I can't install OpenBSD on it. At first sight it seems that every
core components are supported (Via VX700 + Via C7-M - you can check the
PDF Datasheet at http://assets.maxdata.com/?id=128745).

I tried OpenBSD/4.2 and the latest snapshot (from
ftp://ftp.openbsd.org/pub/OpenBSD/snapshots/i386/ and mirrors) and
everytime I get the same result. The laptop loads "bsd.rd" and just
reboot when printing "entry point at..." (before any "blue" writing). I
tried with an USB CD drive and with PXE.

Here is a Linux dmesg if it can help to see if a particular device could
explain the crash :
4.1.1-21)) #1 Sun Feb 10 22:06:33 UTC 2008
BIOS-provided physical RAM map:
  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
  BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
  BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
  BIOS-e820: 0000000000100000 - 000000003bee0000 (usable)
  BIOS-e820: 000000003bee0000 - 000000003beea000 (ACPI data)
  BIOS-e820: 000000003beea000 - 000000003bf00000 (ACPI NVS)
  BIOS-e820: 000000003bf00000 - 0000000040000000 (reserved)
  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000f84b0
On node 0 totalpages: 229376
   DMA zone: 4096 pages, LIFO batch:0
   Normal zone: 225280 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f8470
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x3bee5663
ACPI: FADT (v001 CX700  PTLTW    0x06040000 PTL_ 0x000f4240) @ 0x3bee9a46
ACPI: SSDT (v001 PPmmRe      PPm 0x06040000 INTL 0x20030224) @ 0x3bee9aba
ACPI: MADT (v001 PTLTD   APIC   0x06040000  LTP 0x00000000) @ 0x3bee9f74
ACPI: MCFG (v001 PTLTD    MCFG   0x06040000  LTP 0x00000000) @ 0x3bee9fc4
ACPI: DSDT (v001  VIA   PTL_ACPI 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
ACPI: IRQ10 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Detected 600.029 MHz processor.
Built 1 zonelists.  Total pages: 229376
Kernel command line: root=/dev/hdc1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 901704k/917504k available (1499k kernel code, 15224k reserved,
599k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1200.98 BogoMIPS
(lpj=2401970)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7c9bbff 00100000 00000000 00000000
00004181 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: After all inits, caps: 27c9bbff 00100000 00000000 00000000 00004181
0000ffcc 00000000
Compat vDSO mapped to ffffe000.
CPU: Centaur VIA C7-M Processor 1200MHz stepping 00
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 4641k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: Using MMCONFIG
PCI: No mmconfig possible on 0:0
PCI: No mmconfig possible on 0:1
PCI: No mmconfig possible on 0:f
PCI: No mmconfig possible on 0:10
PCI: No mmconfig possible on 0:11
PCI: No mmconfig possible on 0:13
PCI: No mmconfig possible on 1:0
PCI: No mmconfig possible on 2:1
PCI: No mmconfig possible on 3:9
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *10,
disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *11,
disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *10, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SP2P._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PE._PRT]
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
report
PCI: Failed to allocate mem resource #6:10000@c0000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
   IO window: disabled.
   MEM window: d0000000-d0ffffff
   PREFETCH window: a0000000-bfffffff
PCI: Bridge: 0000:00:13.0
   IO window: disabled.
   MEM window: d1000000-d10fffff
   PREFETCH window: disabled.
PCI: Bridge: 0000:00:13.1
   IO window: 5000-5fff
   MEM window: d1100000-d11fffff
   PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:13.0 to 64
PCI: Setting latency timer of device 0000:00:13.1 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1204385007.676:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 256k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Transitioning device [FAN0] to D0
ACPI: Transitioning device [FAN0] to D0
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 16 throttling states)
ACPI: Thermal Zone [THRM] (54 C)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.0, from 9 to 1
PCI: Setting latency timer of device 0000:00:10.0 to 64
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 177, io base 0x00004400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 22 (level, low) -> IRQ 185
PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 9
PCI: Setting latency timer of device 0000:00:10.1 to 64
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 185, io base 0x00004420
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 193
PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 1
PCI: Setting latency timer of device 0000:00:10.2 to 64
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 193, io base 0x00004440
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[D] -> GSI 23 (level, low) -> IRQ 201
PCI: VIA IRQ fixup for 0000:00:10.4, from 3 to 9
PCI: Setting latency timer of device 0000:00:10.4 to 64
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.4: debug port 1
ehci_hcd 0000:00:10.4: irq 201, io mem 0xd1400000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp 0000:03:09.0: This (id 10ec:8139 rev 10) is not an 8139C+
compatible chip
8139cp 0000:03:09.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:03:09.0[A] -> GSI 16 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:03:09.0 to 64
eth0: RealTek RTL8139 at 0x5000, 00:14:0b:34:60:9c, IRQ 209
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
usb 4-4: new high speed USB device using ehci_hcd and address 3
Probing IDE interface ide0...
Time: acpi_pm clocksource has been installed.
usb 4-4: configuration #1 chosen from 1 choice
usb 4-5: new high speed USB device using ehci_hcd and address 4
usb 4-5: configuration #1 chosen from 1 choice
hub 4-5:1.0: USB hub found
hub 4-5:1.0: 4 ports detected
Probing IDE interface ide1...
usb 4-6: new high speed USB device using ehci_hcd and address 5
usb 4-6: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using uhci_hcd and address 2
hdc: TOSHIBA MK8009GAH, ATA DISK drive
usb 2-1: configuration #1 chosen from 1 choice
usb 4-5.3: new low speed USB device using ehci_hcd and address 6
usb 4-5.3: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver hiddev
input: E N E UTS 6680 as /class/input/input1
input,hiddev96: USB HID v1.10 Mouse [E N E UTS 6680] on usb-0000:00:10.4-5.3
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 512KiB
hdc: 156301488 sectors (80026 MB), CHS=16383/255/63
hdc: cache flushes supported
  hdc: hdc1 hdc2 < hdc5 >
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
   Vendor: Generic-  Model: Multi-Card        Rev: 1.00
   Type:   Direct-Access                      ANSI SCSI revision: 00
usb-storage: device scan complete
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
sd 0:0:0:0: Attached scsi removable disk sda
ts: Compaq touchscreen protocol output
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input2
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new driver hci_usb
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1c0b1, caps: 0xa04750/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input3
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 17 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:02:01.0 to 64
Adding 2650684k swap on /dev/hdc5.  Priority:-1 extents:1 across:2650684k
EXT3 FS on hdc1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
[hidden email]
Linux agpgart interface v0.101 (c) Dave Jones
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
-------

Do you have an suggestion so I can troubleshoot this issue ?

Thank you in advance,
Denis

Reply | Threaded
Open this post in threaded view
|

Re: Belinea s.Book1 can't boot OpenBSD

asmith-4
Oh my, another Nanobook variant.

Try disabling ACPI in the kernel before you boot.

You may want to do this from another machine and copy the new kernel  
to the machine using the Install CD boot because the PS2K device  
doesn't seem to be handled on mine (Packard Bell EasyNote XS) at all  
and I get no key handling in a boot -c.

Regards,

-Andy

On 1 Mar 2008, at 16:52, Denis Fondras wrote:

> Hello,
>
> I'm currently testing a Belinea s.Book1 microlaptop (http://www.belinea.com/en/s_line/product_tagline.jsp?node=652&artnr=399501 
> ) and I can't install OpenBSD on it. At first sight it seems that  
> every core components are supported (Via VX700 + Via C7-M - you can  
> check the PDF Datasheet at http://assets.maxdata.com/?id=128745).
>
> I tried OpenBSD/4.2 and the latest snapshot (from
> ftp://ftp.openbsd.org/pub/OpenBSD/snapshots/i386/ and mirrors) and  
> everytime I get the same result. The laptop loads "bsd.rd" and just  
> reboot when printing "entry point at..." (before any "blue"  
> writing). I tried with an USB CD drive and with PXE.
>
> Here is a Linux dmesg if it can help to see if a particular device  
> could explain the crash :
> 4.1.1-21)) #1 Sun Feb 10 22:06:33 UTC 2008
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
> BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
> BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000003bee0000 (usable)
> BIOS-e820: 000000003bee0000 - 000000003beea000 (ACPI data)
> BIOS-e820: 000000003beea000 - 000000003bf00000 (ACPI NVS)
> BIOS-e820: 000000003bf00000 - 0000000040000000 (reserved)
> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> Warning only 896MB will be used.
> Use a HIGHMEM enabled kernel.
> 896MB LOWMEM available.
> found SMP MP-table at 000f84b0
> On node 0 totalpages: 229376
>  DMA zone: 4096 pages, LIFO batch:0
>  Normal zone: 225280 pages, LIFO batch:31
> DMI present.
> ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f8470
> ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @  
> 0x3bee5663
> ACPI: FADT (v001 CX700  PTLTW    0x06040000 PTL_ 0x000f4240) @  
> 0x3bee9a46
> ACPI: SSDT (v001 PPmmRe      PPm 0x06040000 INTL 0x20030224) @  
> 0x3bee9aba
> ACPI: MADT (v001 PTLTD   APIC   0x06040000  LTP 0x00000000) @  
> 0x3bee9f74
> ACPI: MCFG (v001 PTLTD    MCFG   0x06040000  LTP 0x00000000) @  
> 0x3bee9fc4
> ACPI: DSDT (v001  VIA   PTL_ACPI 0x06040000 MSFT 0x0100000e) @  
> 0x00000000
> ACPI: PM-Timer IO Port: 0x4008
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> Processor #0 6:13 APIC version 20
> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ9 used by override.
> ACPI: IRQ10 used by override.
> Enabling APIC mode:  Flat.  Using 1 I/O APICs
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
> Detected 600.029 MHz processor.
> Built 1 zonelists.  Total pages: 229376
> Kernel command line: root=/dev/hdc1 ro
> mapped APIC to ffffd000 (fee00000)
> mapped IOAPIC to ffffc000 (fec00000)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 16384 bytes)
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 901704k/917504k available (1499k kernel code, 15224k  
> reserved, 599k data, 256k init, 0k highmem)
> Checking if this processor honours the WP bit even in supervisor  
> mode... Ok.
> Calibrating delay using timer specific routine.. 1200.98 BogoMIPS  
> (lpj=2401970)
> Security Framework v1.0.0 initialized
> SELinux:  Disabled at boot.
> Capability LSM initialized
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: a7c9bbff 00100000 00000000  
> 00000000 00004181 00000000 00000000
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 128K (64 bytes/line)
> CPU: After all inits, caps: 27c9bbff 00100000 00000000 00000000  
> 00004181 0000ffcc 00000000
> Compat vDSO mapped to ffffe000.
> CPU: Centaur VIA C7-M Processor 1200MHz stepping 00
> Checking 'hlt' instruction... OK.
> ACPI: Core revision 20060707
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
> checking if image is initramfs... it is
> Freeing initrd memory: 4641k freed
> NET: Registered protocol family 16
> EISA bus registered
> ACPI: bus type pci registered
> PCI: Using MMCONFIG
> PCI: No mmconfig possible on 0:0
> PCI: No mmconfig possible on 0:1
> PCI: No mmconfig possible on 0:f
> PCI: No mmconfig possible on 0:10
> PCI: No mmconfig possible on 0:11
> PCI: No mmconfig possible on 0:13
> PCI: No mmconfig possible on 1:0
> PCI: No mmconfig possible on 2:1
> PCI: No mmconfig possible on 3:9
> Setting up standard PCI resources
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:01:00.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *10,  
> disabled.
> ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *11,  
> disabled.
> ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *10, disabled.
> ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *0, disabled.
> ACPI: PCI Interrupt Link [LNKA] (IRQs 9 *10 11 12)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 9 10 *11 12)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 9 *10 11 12)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 9 10 11 12) *0, disabled.
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SP2P._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PE._PRT]
> ACPI: Power Resource [PFN0] (off)
> ACPI: Power Resource [PFN1] (off)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 9 devices
> PnPBIOS: Disabled by ACPI PNP
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq".  If it helps,  
> post a report
> PCI: Failed to allocate mem resource #6:10000@c0000000 for  
> 0000:01:00.0
> PCI: Bridge: 0000:00:01.0
>  IO window: disabled.
>  MEM window: d0000000-d0ffffff
>  PREFETCH window: a0000000-bfffffff
> PCI: Bridge: 0000:00:13.0
>  IO window: disabled.
>  MEM window: d1000000-d10fffff
>  PREFETCH window: disabled.
> PCI: Bridge: 0000:00:13.1
>  IO window: 5000-5fff
>  MEM window: d1100000-d11fffff
>  PREFETCH window: disabled.
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> PCI: Setting latency timer of device 0000:00:13.0 to 64
> PCI: Setting latency timer of device 0000:00:13.1 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> TCP established hash table entries: 131072 (order: 7, 524288 bytes)
> TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
> TCP: Hash tables configured (established 131072 bind 65536)
> TCP reno registered
> audit: initializing netlink socket (disabled)
> audit(1204385007.676:1): initialized
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> 0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing  
> enabled
> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
> i8042.c: Detected active multiplexing controller, rev 1.1.
> serio: i8042 AUX0 port at 0x60,0x64 irq 12
> serio: i8042 AUX1 port at 0x60,0x64 irq 12
> serio: i8042 AUX2 port at 0x60,0x64 irq 12
> serio: i8042 AUX3 port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> mice: PS/2 mouse device common for all mice
> EISA: Probing bus 0 at eisa.0
> Cannot allocate resource for EISA slot 4
> Cannot allocate resource for EISA slot 5
> EISA: Detected 0 cards.
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> NET: Registered protocol family 8
> NET: Registered protocol family 20
> Using IPI Shortcut mode
> ACPI: (supports S0 S3 S4 S5)
> Freeing unused kernel memory: 256k freed
> Time: tsc clocksource has been installed.
> input: AT Translated Set 2 keyboard as /class/input/input0
> ACPI: Transitioning device [FAN0] to D0
> ACPI: Transitioning device [FAN0] to D0
> ACPI: Fan [FAN0] (off)
> ACPI: Fan [FAN1] (on)
> ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
> ACPI: Processor [CPU0] (supports 16 throttling states)
> ACPI: Thermal Zone [THRM] (54 C)
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with  
> idebus=xx
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> USB Universal Host Controller Interface driver v3.0
> ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 177
> PCI: VIA IRQ fixup for 0000:00:10.0, from 9 to 1
> PCI: Setting latency timer of device 0000:00:10.0 to 64
> uhci_hcd 0000:00:10.0: UHCI Host Controller
> uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
> uhci_hcd 0000:00:10.0: irq 177, io base 0x00004400
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 22 (level, low) -> IRQ 185
> PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 9
> PCI: Setting latency timer of device 0000:00:10.1 to 64
> uhci_hcd 0000:00:10.1: UHCI Host Controller
> uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:10.1: irq 185, io base 0x00004420
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 193
> PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 1
> PCI: Setting latency timer of device 0000:00:10.2 to 64
> uhci_hcd 0000:00:10.2: UHCI Host Controller
> uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:10.2: irq 193, io base 0x00004440
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:10.4[D] -> GSI 23 (level, low) -> IRQ 201
> PCI: VIA IRQ fixup for 0000:00:10.4, from 3 to 9
> PCI: Setting latency timer of device 0000:00:10.4 to 64
> ehci_hcd 0000:00:10.4: EHCI Host Controller
> ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 4
> ehci_hcd 0000:00:10.4: debug port 1
> ehci_hcd 0000:00:10.4: irq 201, io mem 0xd1400000
> ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 6 ports detected
> 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
> 8139cp 0000:03:09.0: This (id 10ec:8139 rev 10) is not an 8139C+  
> compatible chip
> 8139cp 0000:03:09.0: Try the "8139too" driver instead.
> 8139too Fast Ethernet driver 0.9.27
> ACPI: PCI Interrupt 0000:03:09.0[A] -> GSI 16 (level, low) -> IRQ 209
> PCI: Setting latency timer of device 0000:03:09.0 to 64
> eth0: RealTek RTL8139 at 0x5000, 00:14:0b:34:60:9c, IRQ 209
> eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
> usb 4-4: new high speed USB device using ehci_hcd and address 3
> Probing IDE interface ide0...
> Time: acpi_pm clocksource has been installed.
> usb 4-4: configuration #1 chosen from 1 choice
> usb 4-5: new high speed USB device using ehci_hcd and address 4
> usb 4-5: configuration #1 chosen from 1 choice
> hub 4-5:1.0: USB hub found
> hub 4-5:1.0: 4 ports detected
> Probing IDE interface ide1...
> usb 4-6: new high speed USB device using ehci_hcd and address 5
> usb 4-6: configuration #1 chosen from 1 choice
> SCSI subsystem initialized
> Initializing USB Mass Storage driver...
> usb 2-1: new full speed USB device using uhci_hcd and address 2
> hdc: TOSHIBA MK8009GAH, ATA DISK drive
> usb 2-1: configuration #1 chosen from 1 choice
> usb 4-5.3: new low speed USB device using ehci_hcd and address 6
> usb 4-5.3: configuration #1 chosen from 1 choice
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usb-storage: device found at 5
> usb-storage: waiting for device to settle before scanning
> usbcore: registered new driver hiddev
> input: E N E UTS 6680 as /class/input/input1
> input,hiddev96: USB HID v1.10 Mouse [E N E UTS 6680] on  
> usb-0000:00:10.4-5.3
> ide1 at 0x170-0x177,0x376 on irq 15
> hdc: max request size: 512KiB
> hdc: 156301488 sectors (80026 MB), CHS=16383/255/63
> hdc: cache flushes supported
> hdc: hdc1 hdc2 < hdc5 >
> Attempting manual resume
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
>  Vendor: Generic-  Model: Multi-Card        Rev: 1.00
>  Type:   Direct-Access                      ANSI SCSI revision: 00
> usb-storage: device scan complete
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> sd 0:0:0:0: Attached scsi removable disk sda
> ts: Compaq touchscreen protocol output
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> input: PC Speaker as /class/input/input2
> Bluetooth: Core ver 2.10
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> Bluetooth: HCI USB driver ver 2.9
> usbcore: registered new driver hci_usb
> Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1c0b1, caps:  
> 0xa04750/0x200000
> input: SynPS/2 Synaptics TouchPad as /class/input/input3
> Real Time Clock Driver v1.12ac
> ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 17 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:02:01.0 to 64
> Adding 2650684k swap on /dev/hdc5.  Priority:-1 extents:1 across:
> 2650684k
> EXT3 FS on hdc1, internal journal
> loop: loaded (max 8 devices)
> device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [hidden email]
> Linux agpgart interface v0.101 (c) Dave Jones
> eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
> -------
>
> Do you have an suggestion so I can troubleshoot this issue ?
>
> Thank you in advance,
> Denis

Reply | Threaded
Open this post in threaded view
|

Re: Belinea s.Book1 can't boot OpenBSD

Denis Fondras
Andrew Smith a e'crit :

> Oh my, another Nanobook variant.
>
> Try disabling ACPI in the kernel before you boot.
>
> You may want to do this from another machine and copy the new kernel to
> the machine using the Install CD boot because the PS2K device doesn't
> seem to be handled on mine (Packard Bell EasyNote XS) at all and I get
> no key handling in a boot -c.
>
> Regards,
>
> -Andy
>

Hello Andy,

Thank you for the answer.
I tried to build a new kernel but I get the same result, it reboots when
printing "entry point at..."

"boot -c" is useless in my case as it reboots before I can get a prompt :/

Denis

Reply | Threaded
Open this post in threaded view
|

Re: Belinea s.Book1 can't boot OpenBSD

Denis Fondras-2
In reply to this post by Denis Fondras
Another piece of information : none of {Open,Free,Net}BSD will boot on
the beast :/
(Same result : reboot before kernel loading)

Denis