BBB - found 6 disks

Previous Topic Next Topic
 
classic Classic list List threaded Threaded
3 messages Options
Reply | Threaded
Open this post in threaded view
|

BBB - found 6 disks

Jan Stary
This is the latest miniroot-am335x-60.fs onstalling
on a BeagleBone Black. Unlike previous attempts,
it installs on the internal MMC, creating and
mounting the (auto-partitioned) filesystem.
Entire log is below.

While figuring out the disks and where to boot from,
the EFI booting code (is it the EFI booting code)
aventually concludes that there are 6 disks
- that seems wrong. Or is there something in
enumerating devices on the BBB that really makes it six?

However, it boots from the miniroot card just fine.

        Jan


Connected to /dev/ttyU0 (speed 115200)

U-Boot SPL 2016.07 (Aug 29 2016 - 02:55:35)
Trying to boot from MMC1
MMC partition switch failed
*** Warning - MMC partition switch failed, using default environment

reading u-boot.img
reading u-boot.img


U-Boot 2016.07 (Aug 29 2016 - 02:55:35 -0600)

       Watchdog enabled
I2C:   ready
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - bad CRC, using default environment

Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Press SPACE to abort autoboot in 2 seconds
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /am335x-boneblack.dtb
32777 bytes read in 10 ms (3.1 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65192 bytes read in 16 ms (3.9 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 2 not found
MMC Device 3 not found
Found 6 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2168220+7975752+443068 [80+310432+152029]=0xa90670

OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xe05 arg2 0x88000000
Allocating page tables
freestart = 0x80d91000, free_pages = 127599 (0x0001f26f)
IRQ stack: p0x80dbf000 v0xc0dbf000
ABT stack: p0x80dc0000 v0xc0dc0000
UND stack: p0x80dc1000 v0xc0dc1000
SVC stack: p0x80dc2000 v0xc0dc2000
Creating L1 page table at 0x80d94000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 3589
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.  https://www.OpenBSD.org

OpenBSD 6.0-current (RAMDISK) #13: Wed Sep  7 17:05:02 AEST 2016
    [hidden email]:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem  = 536870912 (512MB)
avail mem = 512028672 (488MB)
mainbus0 at root: TI AM335x BeagleBone Black
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
omap0 at mainbus0
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4_wkup"
simplebus2 at simplebus1: "scm"
intc0 at simplebus0 rev 5.0
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: console
tiiic0 at simplebus0 rev 0.11
iic0 at tiiic0
"ti,tps65217" at iic0 addr 0x24 not configured
"at,24c256" at iic0 addr 0x50 not configured
"nxp,tda998x" at iic0 addr 0x70 not configured
tiiic1 at simplebus0 rev 0.11
iic1 at tiiic1
"at,24c256" at iic1 addr 0x54 not configured
"at,24c256" at iic1 addr 0x55 not configured
"at,24c256" at iic1 addr 0x56 not configured
"at,24c256" at iic1 addr 0x57 not configured
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit, mmc high-speed
omdog0 at simplebus0 rev 0.1
cpsw0 at simplebus0: version 1.12 (0), address 90:59:af:82:2e:7e
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, MS, 0000> SCSI2 0/direct fixed
sd0: 15236MB, 512 bytes/sector, 31203328 sectors
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, MMC02G, 0000> SCSI2 0/direct fixed
sd1: 1832MB, 512 bytes/sector, 3751936 sectors
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T

Welcome to the OpenBSD/armv7 6.0 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN.  You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.

Terminal type? [vt220]
System hostname? (short form, e.g. 'foo') bbb

Available network interfaces are: cpsw0.
Which network interface do you wish to configure? (or 'done') [cpsw0]
IPv4 address for cpsw0? (or 'dhcp' or 'none') [dhcp]
DHCPDISCOVER on cpsw0 - interval 1
DHCPOFFER from 192.168.44.1 (68:05:ca:33:6a:61)
DHCPREQUEST on cpsw0 to 255.255.255.255
DHCPACK from 192.168.44.1 (68:05:ca:33:6a:61)
bound to 192.168.44.2 -- renewal in 300 seconds.
IPv6 address for cpsw0? (or 'rtsol' or 'none') [none]
Available network interfaces are: cpsw0.
Which network interface do you wish to configure? (or 'done') [done]
Default IPv4 route? (IPv4 address or none) [192.168.44.1]
add net default: gateway 192.168.44.1
Using DNS domainname stare.cz
Using DNS nameservers at 192.168.44.1 147.32.232.234

Password for root account? (will not echo)
Password for root account? (again)
Start sshd(8) by default? [yes]
Setup a user? (enter a lower-case loginname, or 'no') [no]
Since no user was setup, root logins via sshd(8) might be useful.
WARNING: root is targeted by password guessing attacks, pubkeys are safer.
Allow root ssh login? (yes, no, prohibit-password) [no]
What timezone are you in? ('?' for list) [Europe/Prague]

Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [auto] ?
sd0: SD/MMC MS (14.9G)
sd1: SD/MMC MMC02G (1.8G)
Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [auto] sd1
Disk: sd1 geometry: 233/255/63 [3751936 Sectors]
Offset: 0 Signature: 0xAA55
            Starting     Ending    LBA Info:
 #: id    C H   S -     C H   S [       start:     size ]
-------------------------------------------------------------------------------
*0: 0C    0  32  33 -     2 42  40 [ 2048:    32768 ] Win95 FAT32L
 1: 00    0 0   0 -     0 0   0 [   0: 0 ] unused
 2: 00    0 0   0 -     0 0   0 [   0: 0 ] unused
 3: A6    2  42  41 -   233 139  34 [       34816:  3717120 ] OpenBSD
Use (W)hole disk$ or (E)dit the MBR? [whole]
Creating a msdos partition and an OpenBSD partition for rest of sd1...done.
/dev/rsd1i: 32668 sectors in 8167 FAT16 clusters (2048 bytes/cluster)
bps=512 spc=4 res=1 nft=2 rde=512 sec=32768 mid=0xf8 spf=32 spt=63 hds=255 hid=2048
The auto-allocated layout for sd1 is:
# size offset fstype [fsize bsize   cpg]
  a:      1758.3M 34816 4.2BSD 2048 16384 1 # /
  b: 56.7M       3635744  swap
  c:      1832.0M     0 unused
  i: 16.0M  2048 MSDOS
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] a
/dev/rsd1a: 1758.3MB in 3600928 sectors of 512 bytes
9 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
Available disks are: sd0.
Which disk do you wish to initialize? (or 'done') [done]
/dev/sd1a (85b060d8be5a7aea.a) on /mnt type ffs (rw, asynchronous, local)

Let's install the sets!
Location of sets? (disk http nfs or 'done') [http]
HTTP proxy URL? (e.g. '<a href="http://proxy:8080'">http://proxy:8080', or 'none') [none]
HTTP Server? (hostname, list#, 'done' or '?') [ftp2.eu.openbsd.org]
Server directory? [pub/OpenBSD/snapshots/armv7] csad
ftp: Error retrieving file: 404 Not Found
Looked at http://ftp2.eu.openbsd.org/csad and found no OpenBSD/armv7 6.0 sets. The set names looked for were:
    bsd      comp60.tgz xshare60.tgz  site60-bbb.tgz
    bsd.rd      man60.tgz xfont60.tgz
    bsd.mp      game60.tgz xserv60.tgz
    base60.tgz      xbase60.tgz site60.tgz

Location of sets? (disk http nfs or 'done') [http]
HTTP proxy URL? (e.g. '<a href="http://proxy:8080'">http://proxy:8080', or 'none') [none]
HTTP Server? (hostname, list#, 'done' or '?') [ftp2.eu.openbsd.org] ftp.eu.openbsd.org
Server directory? [pub/OpenBSD/snapshots/armv7]

Select sets by entering a set name, a file name pattern or 'all'. De-select
sets by prepending a '-' to the set name, file name pattern or 'all'. Selected
sets are labelled '[X]'.
    [X] bsd      [X] comp60.tgz [X] xbase60.tgz  [X] xserv60.tgz
    [X] bsd.rd      [X] man60.tgz [X] xshare60.tgz
    [X] base60.tgz    [X] game60.tgz [X] xfont60.tgz
Set name(s)? (or 'abort' or 'done') [done]
Cannot determine prefetch area. Continue without verification? [no] yes
Installing bsd 100% |**************************|  4539 KB    00:03 ETA
Installing bsd.rd 100% |**************************| 10364 KB    00:07 ETA
Installing base60.tgz 100% |**************************| 51347 KB  - 02:31eETA
Extracting etc.tgz 100% |**************************|   187 KB    00:00 ETA
Installing comp60.tgz 100% |**************************| 44473 KB  - 01:30eETA
Installing man60.tgz 100% |**************************|  8540 KB  - 00:36eETA
Installing game60.tgz 100% |**************************|  2708 KB    00:11 ETA
Installing xbase60.tgz 100% |**************************| 19298 KB    00:51 ETA
Extracting xetc.tgz 100% |**************************|  8972      00:00 ETA
Installing xshare60.tgz 100% |**************************|  4406 KB  - 00:25eETA
Installing xfont60.tgz 100% |**************************| 39357 KB    01:18 ETA
Installing xserv60.tgz 100% |**************************|  9436 KB    00:11 ETA
Location of sets? (disk http nfs or 'done') [done]
Time appears wrong.  Set to 'Thu Sep  8 13:03:27 CEST 2016'? [yes]
Saving configuration files...done.
Making all device nodes...done.

CONGRATULATIONS! Your OpenBSD install has been successfully completed!
To boot the new system, enter 'reboot' at the command prompt.
When you login to your new system the first time, please read your mail
using the 'mail' command.

# halt
syncing disks... done
The operating system has halted.
Please press any key to reboot.


(remove the card so that it boots from the internal mmc
where we just installed)


U-Boot SPL 2016.07 (Aug 29 2016 - 02:55:35)
Trying to boot from MMC2
Card did not respond to voltage select!
*** Warning - MMC init failed, using default environment

reading u-boot.img
reading u-boot.img


U-Boot 2016.07 (Aug 29 2016 - 02:55:35 -0600)

       Watchdog enabled
I2C:   ready
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - bad CRC, using default environment

Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Press SPACE to abort autoboot in 2 seconds
Card did not respond to voltage select!
Card did not respond to voltage select!
Card did not respond to voltage select!
Card did not respond to voltage select!
Card did not respond to voltage select!
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
reading /am335x-boneblack.dtb
32777 bytes read in 15 ms (2.1 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65192 bytes read in 19 ms (3.3 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
Card did not respond to voltage select!
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
booting sd0a:/bsd: 3749836+147716+494840 [80+504400+239714]=0x4eaa9c

OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xe05 arg2 0x88000000
Allocating page tables
freestart = 0x807eb000, free_pages = 129045 (0x0001f815)
IRQ stack: p0x80819000 v0xc0819000
ABT stack: p0x8081a000 v0xc081a000
UND stack: p0x8081b000 v0xc081b000
SVC stack: p0x8081c000 v0xc081c000
Creating L1 page table at 0x807ec000
Mapping kernel
Constructing L2 page tables
undefined page pmap [ using 744608 bytes of bsd ELF symbol table ]
board type: 3589
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.  https://www.OpenBSD.org

OpenBSD 6.0-current (GENERIC) #25: Wed Sep  7 16:42:05 AEST 2016
    [hidden email]:/usr/src/sys/arch/armv7/compile/GENERIC
real mem  = 536870912 (512MB)
avail mem = 517836800 (493MB)
mainbus0 at root: TI AM335x BeagleBone Black
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
omap0 at mainbus0
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4_wkup"
simplebus2 at simplebus1: "scm"
intc0 at simplebus0 rev 5.0
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: console
tiiic0 at simplebus0 rev 0.11
iic0 at tiiic0
"ti,tps65217" at iic0 addr 0x24 not configured
"at,24c256" at iic0 addr 0x50 not configured
"nxp,tda998x" at iic0 addr 0x70 not configured
tiiic1 at simplebus0 rev 0.11
iic1 at tiiic1
"at,24c256" at iic1 addr 0x54 not configured
"at,24c256" at iic1 addr 0x55 not configured
"at,24c256" at iic1 addr 0x56 not configured
"at,24c256" at iic1 addr 0x57 not configured
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit, mmc high-speed
omdog0 at simplebus0 rev 0.1
cpsw0 at simplebus0: version 1.12 (0), address 90:59:af:82:2e:7e
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f
sdmmc0: can't enable card
scsibus0 at sdmmc1: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, MMC02G, 0000> SCSI2 0/direct fixed
sd0: 1832MB, 512 bytes/sector, 3751936 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (85b060d8be5a7aea.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
Automatic boot in progress: starting file system checks.
/dev/sd0a (85b060d8be5a7aea.a): file system is clean; not checking
setting tty flags
pf enabled
starting network
DHCPDISCOVER on cpsw0 - interval 1
DHCPOFFER from 192.168.44.1 (68:05:ca:33:6a:61)
DHCPREQUEST on cpsw0 to 255.255.255.255
DHCPACK from 192.168.44.1 (68:05:ca:33:6a:61)
bound to 192.168.44.2 -- renewal in 300 seconds.
reordering libraries: done.
openssl: generating isakmpd/iked RSA keys... done.
ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: no core dump
checking quotas: done.
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
Path to firmware: http://firmware.openbsd.org/firmware/snapshots/
No devices found which need firmware files to be downloaded.
starting local daemons: cron.
Thu Sep 8 13:05:10 CEST 2016

Reply | Threaded
Open this post in threaded view
|

Re: BBB - found 6 disks

Jan Stary
On Sep 08 13:49:25, [hidden email] wrote:
> However, it boots from the miniroot card just fine.

OpenBSD 6.0-current (GENERIC) #25: Wed Sep  7 16:42:05 AEST 2016
    [hidden email]:/usr/src/sys/arch/armv7/compile/GENERIC
real mem  = 536870912 (512MB)
avail mem = 517836800 (493MB)
mainbus0 at root: TI AM335x BeagleBone Black
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
omap0 at mainbus0
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4_wkup"
simplebus2 at simplebus1: "scm"
intc0 at simplebus0 rev 5.0
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: console
tiiic0 at simplebus0 rev 0.11
iic0 at tiiic0
"ti,tps65217" at iic0 addr 0x24 not configured
"at,24c256" at iic0 addr 0x50 not configured
"nxp,tda998x" at iic0 addr 0x70 not configured
tiiic1 at simplebus0 rev 0.11
iic1 at tiiic1
"at,24c256" at iic1 addr 0x54 not configured
"at,24c256" at iic1 addr 0x55 not configured
"at,24c256" at iic1 addr 0x56 not configured
"at,24c256" at iic1 addr 0x57 not configured
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit, mmc high-speed
omdog0 at simplebus0 rev 0.1
cpsw0 at simplebus0: version 1.12 (0), address 90:59:af:82:2e:7e
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SU32G, 0080> SCSI2 0/direct fixed
sd0: 30436MB, 512 bytes/sector, 62333952 sectors
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, MMC02G, 0000> SCSI2 0/direct fixed
sd1: 1832MB, 512 bytes/sector, 3751936 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd0a (93aae518915c8841.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!

Reply | Threaded
Open this post in threaded view
|

Re: BBB - found 6 disks

Jan Stary
In reply to this post by Jan Stary
On Sep 08 13:49:24, [hidden email] wrote:

> This is the latest miniroot-am335x-60.fs installing
> on a BeagleBone Black. Unlike previous attempts,
> it installs on the internal MMC, creating and
> mounting the (auto-partitioned) filesystem.
> Entire log is below.
>
> While figuring out the disks and where to boot from,
> the EFI booting code (is it the EFI booting code?)
> eventually concludes that there are 6 disks
> - that seems wrong. Or is there something in
> enumerating devices on the BBB that really makes it six?

It's still there with the latest snapshot,
but OpenBSD runs just fine.

        Jan